Browsing by Author "Krasota, M."
Now showing 1 - 20 of 43
Results Per Page
Sort Options
Item Аналіз гідродинамічних процесів, що відбуваються у відсіченій порожнині шестеренного насоса(КНТУ, 2016) Кулєшков, Ю. В.; Магонець, Є. В.; Кулєшкова, К. Ю.; Руденко, Т. В.; Красота, М. В.; Kuleshkov, Y.; Mahonets, E.; Kuleshkova, K.; Rudenko, T.; Krasota, M.В статті наведені результати аналізу впливу динамічних процесів, що відбуваються у відсіченій порожнині шестеренного насоса на його працездатність. Зазначені умови виникнення компресії і декомпресії робочої рідини у відсіченій порожнині шестеренного насоса. Встановлено взаємозв’язок між компресією і декомпресією робочої рідини, що виникають у відсіченій порожнині шестеренного насоса і негативним впливом цих явищ на працездатність насоса. Зазначено зниження працездатності шестеренного насоса внаслідок негативного впливу гідродинамічних явищ у відсіченій порожнині, що виявляється у підвищеному зношуванні деталей і з’єднань насоса, зниженні довговічності, коефіцієнту подачі, підвищенні пульсації тиску і подачі, збільшенні вібрацій і шуму НШ. The objective of the work is to analyse scientific and technical information and to determine further directions of research of processes taking place in the isolated section of a gear pump and to formulate scientific hypothesis of the research. The article presents the analysis results of the influence of dynamic processes taking place in the isolated section of a gear pump on its operational performance. The conditions of the occurrence of compression and decompression of hydraulic oil in the isolated section of a gear pump were determined. The interrelationship between the compression and decompression of the hydraulic oil which occurs in the isolated section of a gear pump and the negative influence of these effects on the operational performance of a pump was established. The decrease of operational performance of a gear pump is resulted by the negative influence of hydrodynamic effects in the isolated section. This results the excessive wear of the pump parts and interferences, decrease of service life, pump delivery rate and increase of pressure and delivery pulsation, vibration and noise of the gear pump. It was determined that scientific and technical information does not have physical and mathematic models with the description of hydrodynamic processes taking place in the isolated section of a gear pump. On the basis of the analysis of scientific and technical information we suggested a working hypothesis of the research with the result to exclude the gaps in theory and practice of a gear pump concerning hydrodynamic processes taking place in the isolated section of a gear pump.Item Аналіз причин виникнення шуму в гідроприводах(КНТУ, 2011) Кулєшков, Ю. В.; Руденко, Т. В.; Красота, М. В.; Тітов, Ю. О.; Kuleshkov, J.; Rudenko, T.; Krasota, M.; Titov, J.В статті наведений аналіз джерел шуму в гідравлічних приводах транспорту та технологічного устаткування. Проаналізовано основні параметри, за якими оцінюють рівень шуму в гідроприводах, дано їх визначення. Визначено умови роботи гідроприводу, його основні переваги, а також коливальні процеси, що виникають при експлуатації. Представлена класифікація шумів у гідроприводі за походженням дана їх характеристика. Встановлено основні шляхи поширення шуму у гідроприводі. Зроблено висновок, що механічний шум найбільш характерний для гідросистем з шестеренними насосами. Намічено основні напрямки досліджень по зменшенню механічного шуму у шестеренних насосах. In article the analysis of sources of noise in a hydraulic drive of transport and the process equipment is resulted. Key parameters on which the noise estimation in hydraulic actuators is carried out are analysed, their definition is made. Hydraulic actuator working conditions, its basic advantages are defined, and also oscillatory processes that occur at operation are established. Classification of noise in a hydraulic actuator by origin is presented, their characteristic is given. The basic ways of distribution of noise to hydraulic actuators are established. The conclusion that mechanical noise most typical for hydraulic actuators with pumps is drawn. The basic directions of researches on reduction of mechanical noise in pumps are planned.Item Аналіз теоретичних досліджень геометричних параметрів відсіченої порожнини шестеренного насоса(ЦНТУ, 2017) Кулєшков, Ю. В.; Магонець, Є. В.; Кулєшкова, К. Ю.; Красота, М. В.; Руденко, Т. В.; Kuleshkov, Y.; Magonets, E.; Kuleshkova, K.; Krasota, M.; Rudenko, T.В статті наведені результати аналізу теоретичних досліджень геометричних параметрів відсіченої порожнини шестеренного насоса. Встановлені теоретичні залежності об’єму відсіченої порожнини від параметрів зубчастого зачеплення, а також від положення точки зачеплення на лінії зачеплення шестерень насоса. Отримані теоретичні залежності дозволяють визначити геометричні параметри відсіченої порожнини, при яких виключається явище компресії робочої рідини. Виключення компресії досягнуто завдяки використанню зубчастого зачеплення з асиметричною лінією зачеплення. В роботі вказані недоліки існуючих теоретичних досліджень і вказані напрямки подальшого їх розвитку.The objective of research is to analyze scientific and technical information on the results of theoretical studies of the geometric parameters of the cut-off housing of the gear pump and to determine future direction of research of the processes that take place in the cut-off housing and to formulate the scientific hypothesis of the research. The article presents the results of the analysis of theoretical studies of geometric parameters of the cut-off housing of the gear pump. The theoretical dependences of the volume of the housing on the parameters of toothing were established as well as the position of the point of engagement on the line of contact of a gear pump. The theoretical dependences allow determining geometrical parameters of the cut-off housing which eliminate the phenomenon of the working fluid compression. The avoidance of compression is achieved through the use of toothing with asymmetrical engagement line. The work indicates the shortcomings of existing theoretical research and presents the directions of further development. It was established that one of the possible ways to reduce the impact of the compression of the working fluid in the cut-ff housing is to use toothing with asymmetric line engagement.Item Визначення раціонального радіального зазору в шестеренному насосі гідросистем автотракторної техніки(ЦНТУ, 2022) Кулешков, Ю. В.; Красота, М. В.; Руденко, Т. В.; Осін, Р. А.; Євсейчик, Ю. Б.; Kuleshkov, Yu.; Krasota, M.; Rudenko, T.; Osin, R.; Evseichik, Yu.В статті розглянуто вплив величини радіального зазору між корпусом та шестернями шестеренного насосу гідросистеми автотракторної техніки. Наведені результати досліджень залежності втрат робочої рідини через радіальний зазор між зубами шестерень та корпусом шестеренного насоса. Визначені основні параметри, що впливають на величину втрат та раціональні значення радіального зазору, за яких вони будуть мінімальними. Запропоновано підвищити довговічність шестеренного насоса гідросистем автотракторної техніки наступними шляхами: зменшенням початкового зносу корпусу; виключення подальшого зносу деталей радіального з’єднання використанням ефекту фрикційної складової руху робочої рідини в радіальному зазорі. The research goal is working liquid losses decreasing through the radial clearance in the way of measuring the rational radial clearance between gear teeth and gear pump body. In this research was considered the radial clearance value influences the body and gears of gear pump hydraulic systems of auto and tractor machinery. Given research results of working liquid loses dependency through the radial clearance between teeth and gear pump body. Offered a new way for condition determination in which working liquid losses through radial clearance are minimal. Received terms for working liquid losses measuring, which include the presence of pressurized and friction (viscous) part of losses. Determined main parameters, which allow for management of working liquid losses through radial clearance, such as gear teeth top wideness, gear rotational speed, and gear outer radius. The research of rational radial clearance measuring results allows increasing gear pump manufactory technology efficiency due to optimization of pump details manufactory. Determined main parameters, which influence on losses value and rational radial clearance value and due of which they will be minimal. Offered to increase the durability of gear pump hydraulic systems of auto and tractor machinery work in the next ways: decreasing of starting body deterioration, exclusion further deterioration of radial details connection by using friction part of working liquid movement in radial clearance effect.Item Використання мікродугового оксидування при зміцненні деталей з алюмінієвих сплавів, відновлених пластичним деформуванням(ЦНТУ, 2017) Кулєшков, Ю. В.; Красота, М. В.; Руденко, Т. В.; Матвієнко, О. О.; Kuleshkov, Y.; Krasota, M.; Rudenko, T.; Matvienko, A.У статті приведений аналіз можливості використання нового способу зміцнення - мікродугового оксидування для підвищення зносостійкості деталей, виготовлених з алюмінієвих сплавів, зокрема корпусів шестеренних насосів типу НШ. У роботі викладена сутність процесу зміцнення деталей мікродуговим оксидуванням, представлені основні фізико-механічні характеристики зміцнюючого покриття. Відзначено, що міцність зчеплення і механічні властивості покриття багато в чому залежать від стану поверхні, що зміцнюється, зокрема від методу попередньої обробки. При цьому встановлено, що зміцнюючі покриття після пластичного деформування деталей мають вищу міцність зчеплення, твердість і більшу товщину. У роботі представлені основні відомості про мікродугове оксидуванні, які на думку авторів будуть сприяти застосуванню маловивченого способу зміцнення в ремонтному виробництві. The objective of the research is to analyse the scientific and technical information on hardening of parts of aluminium alloys by micro-arc oxidation, particularly the parts, which were repaired by hot plastic deformation. This article presents the analysis of the possibility to apply a new method of hardening of working surfaces of parts by micro-arc oxidation to increase wearability of working surfaces of the parts made of aluminium alloys, in particular the bodies of gear pumps. The work presents the essence of the process of hardening of details by micro-arc oxidation and the main physical and chemical characteristics of the hardening coating. It was stated that the adhesive strength and mechanical characteristics of the coating largely depend on the condition of the surface under hardening, in particular on the method of preparatory processing. It was established that the hardening coating of metal after plastic deformation gets better adhesive strength, thickness and hardness. The work presents basic information on micro-arc oxidation which will facilitate further application of the hardening method in repair industry.Item Відновлення автомобільних деталей наплавленням композиційних матеріалів(ЦНТУ, 2020) Красота, М. В.; Осін, Р. А.; Боклаг, А. І.; Красота, М. В.; Осин, Р. А.; Боклаг, А. И.; Krasota, M.; Osin, R.; Boklah, A.Item Відновлення поршневих пальців гарячим пластичним деформуванням(ЦНТУ, 2021) Кулєшков, Ю. В.; Красота, М. В.; Руденко, Т. В.; Осін, Р. А.; Рева, В. Г.; Kuleshkov, Yu.; Rudenko, T.; Krasota, M.; Osin, R.; Reva, V.Одним з перспективних методів відновлення поршневих пальців шатунно – поршневої групи двигунів внутрішнього згорання є метод гарячої пластичної деформації. Процес відновлення поршневих пальців гарячим пластичним деформуванням дозволяє підвищити їх міцність і, зокрема втомну міцність. При розробці технологічного процесу відновлення поршневих пальців із використанням методу гарячої пластичної деформації шляхом його роздачі пуансоном в штампі виникає задача визначення зусилля, яке необхідно для якісного проведення процесу деформації. У статті пропонуються теоретичні основи розрахунку зусиль деформації. Результат був отриманий на основі обраної схеми формоутворення. The aim of the study is to create a theoretical basis that allows to calculate the forces of hot plastic deformation of the piston pin. One of the promising methods of restoring the piston fingers of the connecting rod - piston group of internal combustion engines is the method of hot plastic deformation. The process of restoring the piston fingers by hot plastic deformation can increase their strength and, in particular, fatigue strength. When developing the technological process of restoration of piston fingers using the method of hot plastic deformation by distributing it with a punch in the stamp, there is a problem of determining the effort required for high-quality deformation process. The article offers the theoretical basis for calculating the deformation forces. The result was obtained on the basis of the selected scheme of formation. As a result of the calculations we can conclude: 1. Restoration of the piston finger by hot plastic deformation allows to restore 95% of the fingers which have arrived in repair. 2. Piston fingers restored by hot plastic deformation in their technical parameters are not inferior to the new, achieved - "healing" of microcracks, creating internal compressive stresses, and grinding grain, which strengthens the material of the piston finger, in particular increasing its fatigue strength by 15… 20% . 3. As a result of theoretical studies of the resistance of the metal to plastic deformation were obtained dependences of the specific force on the punch depending on the ratio of the diameters of the workpiece.Item Дослідження методів обробки порошкових покриттів(КНТУ, 2011) Красота, М. В.; Шепеленко, І. В.; Василенко, І. Ф.; Русских, В. В.; Krasota, M.; Shepelenko, I.; Vasilenko, I.; Russky, V.В статті наведено аналіз методів обробки порошкових покриттів, що використовуються на теперішній час, виявлено їх недоліки. Розглянуто альтернативні методи обробки та можливість їх використання для покриттів, що отримуються методами наварювання, наплавлення та напилювання порошкових матеріалів. Запропоновано використання поверхневого пластичного деформування для калібрування поверхні та зменшення припуску на подальшу механічну обробку. Через високу твердість та крихкість порошкових покриттів деформування пропонується виконувати у твердому стані з використанням остаточного тепла в одному технологічному циклі з нанесенням покриття. In article the analysis of methods of processing of powder coverings is resulted that are used at present, their lacks are defined. Alternative methods of processing and possibility of their use for coverings that are put by methods of welding and a dusting of powder materials are considered. It is offered to use superficial plastic deformation for calibration of a surface and reduction of an allowance by the subsequent machining. Because of high hardness and fragility of coverings deformation is offered to be carried out in a firm condition with use of residual heat in one work cycle with covering drawing.Item Дослідження розподілення електричного струму при відновленні автомобільних деталей контактним наварюванням(ЦНТУ, 2020) Кулешков, Ю. В.; Красота, М. В.; Руденко, Т. В.; Осін, Р. А.; Kuleshkov, Yu.; Krasota, M.; Rudenko, T.; Osin, R.; Осин, Р. А.В статті розглянуті причини нерівномірності густини електричного поля при контактному наварюванні компактних (дріт, стрічка) та порошкових матеріалів при відновленні деталей автомобілів. Нерівномірність густини струму визначає нерівномірне розподілення температурного поля в зоні утворення литого ядра і впливає на якість наварених покриттів. При контактному наварюванні компактних матеріалів відбувається недогрівання центральної зони ядра, що спричиняється дією геометричного, температурного і магнітоелектричного чинників. При наварюванні порошкових матеріалів густина електричного поля вища в центральних зонах, що обумовлюється більш високим ступенем ущільнення порошкового матеріалу в цій зоні. При наварюванні порошкового матеріалу центральна зона нагрівається до більш високих температур ніж граничні зони. Неоднорідні електричні поля при контактному наварюванні розглянутих матеріалів приводять до зниження функціональних властивостей покриттів. The goal of completed research is determination of common factors of dynamic electricity distribution in the area of simple welding spot forming due to contact welding-on compact and powdered materials. Due to contact welding-on of compact (rod, belt) and powdered materials there is the dissimilarity of an electric field, which determines the unequal distribution of temperature field in the area of the moulded core creating and influence on the welded on covering quality. By the contact welding-on of compact materials, there is an occurrence of central core zone unheating, which is coming as a result of geometrical, temperature and magnetic-electric factors. During contact welding of metal powders, considering high speed of heating and a small-time of dynamic electricity passage through powder, it is possible to make a conclusion, that the stability of heat generation in a powder surface will be determined by starting electricity resistance value. High-quality plating can be reached if the powder charge will have low and stable electricity resistance in a cross-section and good compactness under the condition of low compress pressure, which is used for welding. (40 ... 70 MPa). Electrical field dissimilarity with contact welding-on powdered materials leads to unequal heating of powdered materials and covering defects, which is taking place due to the features of powder compression. As a result of current lines concoction in the central area is observed at a local temperature increase. Besides, interstices are dielectrical phase and increase electrical resistance in the peripheral areas. To increase the quality of coverings, got by contact welding-on is able due to providing high-quality powder material compression on the whole covering cut. В статье рассмотрены причины неравномерности плотности электрического поля при контактном наваривании компактных (проволока, лента) и порошковых материалов при восстановлении деталей автобилей. Неравномерность плотности тока определяет неравномерное распределения температурного поля в зоне образования литого ядра и влияет на качество наваренных покрытий. При контактном наваривании компактных материалов происходит недогрев центральной зоны ядра, что вызывается действием геометрического, температурного и магнитоэлектрического факторов. При наваривания порошковых материалов плотность электрического поля выше в центральных зонах, что обуславливается более высокой степенью уплотнения порошкового материала в этой зоне. При наваривании порошкового материала центральная зона нагревается до более высоких температур, чем граничные зоны. Неоднородные электрические поля при контактной наварке рассмотреных материалов приводят к снижению функциональных свойств покрытий.Item Дослідження розподілення струму у зварювальній точці при контактному наварюванні(ЦНТУ, 2020) Красота, М. В.; Осін, Р. А.; Красота, М. В.; Осин, Р. А.; Krasota, M.; Osin, R.Item Енергозберігаючий гідропривід механізму піднімання кузова автомобіля-самоскида(ЦНТУ, 2018) Кулєшков, Ю. В.; Руденко, Т. В.; Красота, М. В.; Кулешков, Ю. В.; Kuleshkov, Yu.; Rudenko, T.; Krasota, M.В даній статті запропоновано конструкцію оригінального гідроприводу механізму піднімання кузова автомобіля-самоскиду. Особливістю даної гідросистеми є використання гідроакумулятора високого тиску, плунжерних насосів, системи керування, при цьому шестеренний насос та його привід від двигуна автомобіля, характерні для серійного механізму піднімання, в пропонованій схемі відсутні. Як джерело енергії, необхідної для піднімання кузова, пропонується використовувати не двигун внутрішнього згорання, як в серійних гідроприводах, а гідроакумулятор з підзаряджанням від коливань підресорених мас автомобіля. В статье предложено конструкцию оригинального гидропривода механизма подъема кузова автомобиля-самосвала. Особенностью данной гидросистемы является использование гидроаккумулятора высокого давления, плунжерных насосов, системы управления, при этом шестеренный насос и его привод от двигателя автомобиля, характерные для серийного механизма подъема, в предложенной схеме отсутствуют. В качестве источника энергии, необходимой для подъема кузова, предлагается использовать не двигатель внутреннего сгорания, а гидроаккумулятор с подзарядкой от колебаний подрессоренных масс автомобиля. The goal of researching is finding alternative constructions of hydraulic actuator of the carcass lifting device, which are working without using internal combustion engine energy and, consequently, guarantee energy saving and economical effect of technological car using. In the article it was offered the construction of original hydraulic actuator of the carcass lifting device. The feature of such hydraulic system is using hydraulic accumulator of high pressure, plunger pumps, control systems, herewith gear pump and its drive from car engine, which are specific for serial lifting mechanism, in the offered scheme are not present. As a source of energy, which is needed to lift the carcass, was offered not to use the internal combustion engine, but hydraulic accumulator with recharging from chattering of the car sprung mass. The feature of this hydrosystem is the use of a high pressure accumulator, plunger pumps, control system, with the gear pump and its drive from the engine of the car, typical for the serial lift mechanism, in the proposed scheme are absent. As a source of energy necessary for lifting the body, it is proposed not to use an internal combustion engine, as in serial hydraulic drives, and a hydraulic accumulator with the energy of the working fluid accumulated from the oscillations of the submerged car's masses. Was counted the economy, which can be earned by the reducing of the fuel uses, during realization of unloading operations of one car per year.Item Зміцнення деталей з алюмінієвих сплавів мікродуговоговим оксидуванням(ЦНТУ, 2021) Кулєшков, Ю. В.; Красота, М. В.; Руденко, Т. В.; Осін, Р. А.; Крошка, В. Д.; Kuleshkov, Yu.; Krasota, M.; Rudenko, T.; Osin, R.; Kroshka, V.У статті наведено результати аналізу можливості використання нового способу зміцнення робочих поверхонь деталей – мікродугового оксидування для підвищення зносостійкості робочих поверхонь деталей, виготовлених з алюмінієвих сплавів, зокрема корпусів шестеренних насосів типу НШ. У роботі викладена сутність процесу зміцнення деталей мікродуговим оксидуванням, представлені основні фізико-механічні характеристики зміцнюючого покриття. Відзначено, що міцність зчеплення і механічні властивості покриття багато в чому залежать від стану зміцнюючої поверхні, зокрема від методу попередньої обробки. При цьому встановлено, що зміцнюючі покриття металу після пластичного деформування мають більшу міцність зчеплення, більшу товщиною і твердістю. Представлені основні відомості про мікродугове оксидуванні, які на думку авторів будуть сприяти освоєнню маловивченого способу зміцнення в ремонтному виробництві. The purpose of the research is to analyze the scientific and technical information to determine the possibility of strengthening the parts of aluminum alloys by microarc oxidation, in particular gear pump housings. The article presents the results of the analysis of possibility of using a new method of hardening roboczych surfaces - micro-arc oxidation to enhance the wear resistance of working surfaces of parts made of aluminum alloys, in particular housings, gear pumps NSH. The paper describes the essence of the process of hardening parts by microarc oxidation, presents the main physical and mechanical characteristics of the hardening coating. It is noted that the adhesion strength and mechanical properties of the coating largely depend on the state of the surface to be strengthened, in particular, on the method of pretreatment. At the same time, it was found that the strengthening coating of the metal after plastic deformation has a greater adhesion strength, greater thickness and hardness. The paper presents the basic information about microarc oxidation, which, according to the authors, will contribute to the development of the method in the poorly studied method of hardening in repair production. It can be concluded that the ceramic coatings obtained by microarc oxidation can be recommended for the restoration and strengthening of aluminum parts of gear pumps, in particular the pump housing.Item Зниження масогабаритних показників шестеренного насоса оптимізацією параметрів зубчатого зачеплення(ЦНТУ, 2018) Кулєшков, Ю. В.; Руденко, Т. В.; Красота, М. В.; Осін, Р. А.; Кулешков, Ю. В.; Осин, Р. А.; Kuleshkov, Yu.; Rudenko, T.; Krasota, M.; Osin, R.В статті розглянуті питання зниження маси і габаритів шестеренних насосів шляхом оптимізації параметрів зубчатого зачеплення. Оптимізація проводилась в напрямку підвищення питомих показників насоса: робочого об’єму і подачі. Підвищення питомих показників дозволило знизити габарити вузла насоса, що качає, шляхом зменшення ширини шестерень при збереженні робочого об’єму насоса, що в кінцевому результаті привело до зниження габаритних розмірів і маси зпроектованого насоса. В статье рассмотрены вопросы снижения массы и габаритов шестеренных насосов путем оптимизации параметров зубчатого зацепления. Оптимизация проводилась в направлении повышения удельных показателей насоса: рабочего объема и подачи. Повышение удельных показателей позволило снизить габариты качающего узла насоса путем уменьшения ширины шестерён при сохранении рабочего объема насоса, что в конечном результате привело к снижению габаритных размеров и массы спроектированного насоса. The object of the completed research is reducing mass and dimensions parameters of gear pump with saving of its technical characteristics and realization technical and economical effect. As the result of the optimization gear-tooth system parameters of gear pump, the construction of gear pump with increased specific working volume and output was designed. In the process of adapting the construction of an experimental pump with increased specific working volume to the production conditions, the possibility of decreasing of the gear width with keeping specific working volume, which corresponds to the standard value, was set. This made it possible to reduce the load on the pump bearings, with an offer of new dependence for calculating of the load on the pump bearing, which is determined by the gear-tooth system overlap coefficient. In the process of designing a gear pump with optimal parameters and the adaptation to its operating parameters to standard values, was found the possibility of reducing the dimensions and mass of the designed pump.Item Исследование закономерностей изменения геометрических параметров зубчатого зацепления шестеренного насоса(КНТУ, 2014) Кулешков, Ю. В.; Черновол, М. И.; Руденко, Т. В.; Красота, М. В.; Магопець, С. О.; Кулешкова, К. Ю.; Кулєшков, Ю. В.; Черновол, М. І.; Кулєшкова, К. Ю.; Kuleshkov, Y.; Chernovol, M.; Rudenko, T.; Krasota, M.; Magopetz, S.; Kuleshkova, K.В статье приведено доказательство теоремы об особенностях движения элементов эвольвентного зубчатого зацепления, которая является теоретической базой снижения пульсации геометрической мгновенной подачи шестеренного насоса на всем протяжении зубчатого зацепления, исключая полюс зацепления. В статті наведено доведення теореми про особливості руху елементів евольвентного зубчастого зачеплення, яка є теоретичною базою зниження пульсації геометричної миттєвої подачі шестеренного насоса протягом всього зубчастого зачеплення, крім полюса зачеплення. The objective of the research is the development of theory to create a physical and mathematical model of the process of instant feed of a gear pump. That will allow explaining the peculiarities of the instant feed and the pressure in the process of operating cycle. The article presents the proof of the theorem about special movement of the elements of evolute toothing which is the theoretical basis of the decrease of pulsation of geometrical instant feed of gear pump during all the period of toothing excluding the pitch point. We have proved the theorem of the theory of evolute toothing which determines the speed of area change described by radiuses that connect the centres of gear rotation with pitch point. The proved theorem may be used while designing gear pumps because in a gear pump the evolute toothing carries out two functions. First, toothing is used to transport hydraulic fluid from suction chamber to injection chamber and provides increase of pressure of hydraulic fluid together with other sealing elements of a pump. Second, toothing plays a traditional role of transforming of rotation moment from pump drive to driven gear. It is an additional function in a gear pump. The proof of the theorem shows that traditional image of pulsation of instant feed and pressure in the process of feed of hydraulic fluid in gear pumps is not absolutely true to the reality.Item Методика стендових випробовувань шестеренного насоса(КНТУ, 2011) Кулєшков, Ю. В.; Руденко, Т. В.; Красота, М. В.; Матвієнко, О. О.; Титов, Ю. А.; Kuleshkov, J.; Rudenko, T.; Krasota, M.; Matvienko, A.; Titov, J.Розроблена програма досліджень, яка включала методики дослідження основних технічних характеристик НШ для різних значень тиску, робочого об’єму насоса і частоти обертання, і перевірку ступеня збігу основних теоретичних положень і висновків з результатами, отриманими експериментальним шляхом. Розглянуто методики випробувань шестеренних насосів з регульованою подачею, наведено будову та характеристика дослідного обладнання. Викладено методику обробки даних, отриманих при проведенні експериментальних досліджень. The program of researches including techniques of research of basic tehniche-skih of characteristics gear-type pumps for different values of pressure, working volume of the pump and frequency of rotation, check of degree of coincidence of the basic theoretical positions and conclusions with the results, luchen th experimentally is developed. Techniques of tests gear-type pumps from a reguliro-bathroom are considered by giving, the device and the characteristic of the research equipment is resulted. The technique of the data processing, the experimental researches received at carrying out is stated.Item Оптимизация зубчатого зацепления шестеренного насоса с целью повышения его удельной подачи(КНТУ, 2011) Кулешков, Ю. В.; Осин, Р. А.; Руденко, Т. В.; Красота, М. В.; Кулєшков, Ю.; Kuleshkov, J.; Osin, R.; Rudenko, T.; Krasota, M.Предложена математическая модель оптимизации зубчатого зацепления шестеренного насоса типа НШ, позволяющая определить такие его параметры, при которых параметр оптимизации зубчатого зацепления - коэффициент использования объема венцов шестерен, а вместе с тем и удельная подача шестеренного насоса достигает максимального для данных геометрических размеров насоса значений. Запропоновано математичну модель оптимізації зубчастого зачеплення шестеренного насоса типу НШ, що дозволяє визначити такі його параметри, при яких параметр оптимізації зубчастого зачеплення - коефіцієнт використання об’єму вінців шестірень, а разом з тим і питома подача шестеренного насоса досягає максимального для даних геометричних розмірів насоса значень. New approach is offered to the losses of working liquid through a butt end gap in the in gear pumps of НШ-type. Dividing of losses of working liquid into three allowed to perfect constituents existent pictures of losses of butt ends of working liquid in gear pumps. The mathematical model of losses of working liquid through the intercentral sector of butt end interface is offered in first time.Item Особенности проектирования шестеренного насоса с повышенной подачей(КНТУ, 2012) Кулешков, Ю. В.; Осин, Р. А.; Руденко, Т. В.; Красота, М. В.; Кулешков, Ю.; Осин, Р.; Руденко, Т.; Красота, М.; Kuleshkov, Y.; Osin, R.; Rudenko, T.; Krasota, M.На основе разработанных новых физических и математических моделей процесса подачи шестеренного насоса была предложена методика расчета параметров зубчатого зацепления с оптимальными параметрами. Решена задача адаптации шестеренного насоса с увеличенным удельным рабочим объемом к условиям производства, что обеспечило получение экономического эффекта. На основі розроблених нових фізичних і математичних моделей процесу подачі шестеренного насоса була запропонована методика розрахунку параметрів зубчастого зачеплення з оптимальними параметрами. Розв'язана задача адаптації шестеренного насоса із збільшеним питомим робочим об'ємом до умов виробництва, що забезпечило отримання економічного ефекту. On the basis of the worked out new physical and mathematical models of process of serve of шесте-ренного pump methodology of calculation of parameters of the toothed hooking was offered with optimal parameters. The task of adaptation of cog-wheel pump is decided with the megascopic specific swept volume to the terms of production, that provided the receipt of economic effect.Item Особенности работы и конструкции шестеренного насоса(ЦНТУ, 2017) Кулешков, Ю. В.; Руденко, Т. В.; Красота, М. В.; Магонец, Е. В.; Осин, Р. А.; Кулєшков, Ю. В.; Магонець, Є. В.; Осін, Р. А.; Kuleshkov, Yu.; Rudenko, T.; Krasota, M.; Magonets, E.; Osin, R.В статье рассмотрены особенности конструкции шестеренного насоса, объясняющие его высокий уровень удельной мощности в сравнении с другими типами объемных насосов. Представлены в виде моделей характерные особенности работы шестеренного насоса, что позволило сформулировать пути дальнейшего усовершенствования конструкции шестеренного насоса в направлении повышения его технического уровня. В статті розглянуті особливості конструкції шестерінчастого насоса, які пояснюють його високий рівень питомої потужності у порівнянні з іншими типами об’ємних насосів. Представлено у вигляді моделей характерні особливості роботи шестеренного насоса, що дозволило сформулювати шляхи подальшого удосконалювання конструкції шестеренного насоса в напрямку підвищення його технічного рівня. The objective of research is to explain certain aspects of gear-type pump work, understanding of which allows to formulate tasks of farther increasing its technical level. The article describes the special aspects of construction gear-type pump, which explains its high level of unit power in comparison with other kinds of massive pumps. Submitted in a form typical aspects of gear-type pump work, which allows to formulate the ways of farther upgrading the gear-type pump construction towards increasing its technical level. Offered schemes of work allows to explain such negative feature in the gear-type pump as split off void, pulsating of pressure and giving in causal-resultative categories.Item Особливості утворення радіального зазору в шестеренних насосах гідросистем автотракторної техніки(ЦНТУ, 2022) Кулешков, Ю. В.; Красота, М. В.; Руденко, Т. В.; Осін, Р. А.; Євсейчик, Ю. Б.; Kuleshkov, Yu.; Krasota, M.; Rudenko, T.; Osin, R.; Evseichik, Yu.В статті наведені результати досліджень впливу способу формування радіального зазору шестеренного насоса, що використовується в гідравлічних системах автотракторної техніки, врізанням шестерень в корпус насоса під час обкатування на його технічні характеристики. Розглянуто основні переваги та недоліки даного способу, та встановлено, що існуючий спосіб формування радіального зазору врізанням шестерні в корпус на сьогоднішній день не відповідає вимогам, що висуваються до насосів. Використання способу врізання шестерень негативно позначається на коефіцієнті подачі і довговічності насоса. В роботі запропоновано спосіб формування радіального зазору, що полягає у отриманні мінімального радіального зазору між шестернями та корпусом за рахунок більш точного виготовлення шестерень по діаметру вершин. Даний метод не передбачає врізання шестерень в корпус насоса, що забезпечує збільшення довговічності насоса вцілому. The research goal is the analysis of the existing radial clearance forming method in gear pump details connection “body – gear teeth”, which provides the minimal size of radial clearance with the low accuracy of manufacturing details and offers another rational method of radial clearance creating. In this research was considered creating radial clearance between body and gears of gear pump hydraulic systems of auto and tractor machinery. The technology of gear pump manufacturing after pump folding provides it's enabling on a special stand in order to disability verification. During the period of enabling, as mentioned before, gear teeth cutting into the body happens with forming a so-called «bed», which must provide a radial clearance seal. Given research results of way of radial gear pump clearance forming influence, which is used in hydraulic systems of auto and tractor machinery, gears cutting in pump body during enabling for technical characteristics. Considered the main advantages and disadvantages of this method, and found, that existed way of radial clearance forming by cutting gear into the body, today does not comply with the requirements for pumps. Using the method of gear cutting negatively impacts the supply rate and pump durability. Offered a new way of radial clearance forming, which consists of getting a minimal radial clearance between gears and body due to more accurate gears manufacturing top diameter. This method does not provide gears cutting into the pump body, which increases pump durability. An effective method of radial clearance forming is more accurate manufacturing and folding pump details. The results of experimental research show that increasing radial clearance to certain sizes does not influence on pump supplying rate significantly.Item Оцінка міцності поршневих пальців, відновлених за рахунок роздачі внутрішнього отвору(ЦНТУ, 2022) Немировський, Я. Б.; Шепеленко, І. В.; Красота, М. В.; Nemyrovskyi, Ya.; Shepelenko, I.; Krasota, M.Одним із найбільш прогресивних методів відновлення поршневих пальців ДВЗ є роздача внутрішнього отвору, що забезпечує збільшення зовнішнього діаметра зношеного пальця. У процесі подальшої обробки виконується знімання припуску із зовнішньої поверхні, що викликає витончення стінки та необхідність проведення розрахунків на міцність пальця. В роботі виконані перевірочні розрахунки міцності пальців двигунів Д245. При цьому використана схема із жорстким закріпленням вільних кінців, для чого розраховано статично невизначену балку. Виконано експериментальну перевірку аналітичних розрахунків. Проведені дослідження дозволили встановити, що використання роздачі отвору при відновленні поршневих пальців не змінює міцність та геометричні характеристики деталі. Це дозволило рекомендувати дану технологію при відновленні робочих поверхонь поршневих пальців. One of the most progressive methods of proceeding in the piston fingers of engines of internal combustion there is distribution of the internal opening that provides the increase of external diameter of threadbare finger. In the process of further treatment the output of assumption is executed from an external surface that causes reduction walls and necessity of realization of calculations on durability of finger. The aim of researches is realization of calculation on durability of piston fingers of engines of internal combustion, treat the deforming reaching. It is considered existing methodologies of estimation of durability of finger. The checking calculations of durability of fingers of motor-vehicle and tractor engines are in-process executed. Thus used chart with the hard fixing of free ends, for what an indefinite beam is expected static. The terms of fixing of finger are analysed in a piston. Verification of analytical calculations executed on the experimental setting. Realization of research allowed to set next conclusions: 1. Methodology of calculation is improved on durability of piston fingers. The use of an offer methodology allowed to execute checking calculations on durability of piston fingers of motor-vehicle and tractor engines. 2. Experimental verification of theoretical positions allowed to assert about correctness offered approach near a calculation on durability. 3. The executed analytical calculations and experimental researches showed that using of method of distribution of the internal opening for proceeding in piston fingers not substantially influenced on their durability and geometrical descriptions. It allows to recommend this technology for proceeding in this class of details.
- «
- 1 (current)
- 2
- 3
- »