Browsing by Author "Molokost, L."
Now showing 1 - 11 of 11
Results Per Page
Sort Options
Item Investigation of the effect of slag catcher design on slag delay efficiency in the SolidWorks Flow Simulation parametric modeling environment(United Kingdom, 2020) Kononchuk, S.; Molokost, L.; Pukalov, V.; Конончук, С. В.; Молокост, Л. А.; Пукалов, В. В.The influence of the design of the slag catcher on the efficiency of slag retention is investigated. SolidWorks Flow Simulation parametric modeling CAE module confirms the possibility of reducing the melt velocity through the use of a slag catcher with braking ribs. An original design of a ribbed slag catcher is proposed, which ensures trapping of slags and smooth filling of the mold with an alloy due to a decrease in the speed of movement of the melt without additional metal costs. It was found that the flow velocity along the cross-sectional height of the proposed ribbed slag catcher is less by 0.028 m / s or 14.5% compared to the traditional one. Using a ribbed slag catcher printed on a 3D printer, a mold was produced that showed satisfactory molding ability.Item До питання структуроутворення високоміцного чавуну при використанні діаграм стану систем «Fe- Si», «Mg-Si» та «Fe-Si-Mg»(ЦНТУ, 2023) Кропівний, В. М.; Босий, М. В.; Кузик, О. В.; Кропівна, А. В.; Молокост, Л. А.; Kropivnyi, V.; Bosyi, M.; Kuzyk, О.; Kropivna, А.; Molokost, L.У статті наведено результати аналізу закономірностей структуроутворення високоміцного чавуну при використанні діаграм стану систем «Fe-Si», «Mg-Si» та «Fe-Si-Mg». Розглянуто концепцію утворення графіту у високоміцному чавуні. Наведено схему формування структури високоміцного чавуну. Встановлено, що при модифікуванні розплаву чавуну в результаті істотного перерозподілу всіх розчинених у ньому елементів відбувається очищення рафінування від домішок (сірка, фосфор та ін.), що дозволяє отримувати структуру чавуну з кулястим графітом із застосуванням модифікаторів. Приведені діаграми системи «Fe-Si», «Mg-Si» та системи «Fe-Si-Mg» для розробки складу високоміцного чавуну. Аналіз даних приведених діаграм стану, показав, що всі сполуки елементів в складі сфероїдизуючих лігатур є легкоплавкими (tпл < 1300 °С) по відношенню до температури розплаву чавуну. При кристалізації чавуну з виділенням аустеніту характерна пряма мікроліквація кремнію з коефіцієнтом розподілу менше одиниці, марганець більш рівномірно розподіляється в металі, а в рідку фазу ліквують карбідостабілізуючі елементи. The purpose of the work is to establish the patterns of structural formation of high-strength cast iron using the thermodynamic theory of phase transformations and to analyze state diagrams of the components of Fe-Si-Mg ligatures. The article presents the results of the analysis of patterns of structural formation of high-strength cast iron when using state diagrams of the "Fe-Si", "Mg-Si" and "Fe-Si-Mg" systems. The concept of graphite formation in high-strength cast iron is considered. The structure formation scheme of high-strength cast iron is presented. Disclosure of the mechanism of processes of formation of spherical and vermicular graphite opens wide opportunities for controlling the structure and properties of high-strength cast iron and contributes to the development of effective technological processes for obtaining cast products for various purposes. It has been established that during the modification of cast iron melt, as a result of a significant redistribution of all elements dissolved in it, purification of impurities (sulfur, phosphorus, etc.) takes place, which allows obtaining the structure of cast iron with nodular graphite with the use of modifiers. Diagrams of the "Fe-Si", "Mg-Si" and "Fe-Si-Mg" systems for the development of the composition of high-strength cast iron are given. After analyzing the data of the given state diagrams, it was concluded that in the composition of spheroidizing ligatures, all compounds of elements are low-melting (tpl < 1300 °С) in relation to the melting temperature of cast iron. During the crystallization of cast iron with the release of austenite, a direct microliquation of silicon with a distribution coefficient less than unity is characteristic, manganese is more evenly distributed in the metal, and carbide stabilizing elements are treated in the liquid phase. The regularities of structure formation of modified cast iron under different crystallization conditions have been established. The analysis of the study of the regularities of the process of the formation of spherical and vermicular graphite and the analysis of state diagrams of the "Fe-Si-Mg" liga-tur components were performed.Item До створення концепції «ідеального» решета зернового сепаратора(ЦНТУ, 2020) Васильковський, О. М.; Лещенко, С. М.; Мороз, С. М.; Нестеренко, О. В.; Молокост, Л. А.; Vasylkovskyi, O.; Leshchenko, S.; Moroz, S.; Nesterenko, O.; Molokost, L.; Васильковский, А. М.; Лещенко, С. Н.; Мороз, С. Н.; Нестеренко, А. В.У статті викладені міркування щодо створення умов для інтенсифікації процесу сепарації зерна за геометричними ознаками. Проведено огляд конструкцій і аналіз роботи відомих решітних поверхонь з позиції можливості забезпечення високих показників технологічної ефективності за рахунок прискорення орієнтації часток відносно отворів решета. Встановлено, що найбільш сприятливі умови орієнтації забезпечують поверхні, утворені повздовжніми елементами малого перерізу обтічної форми, що мінімізують можливість розташування на них часток в положеннях стійкої рівноваги. Виявлено теоретичні можливості збільшення площ живого перерізу та коефіцієнтів живого перерізу решітних полотен, що не мають поперечних перетинок. Наведені залежності сумарної ширини повздовжніх перетинок і коефіцієнта живого перерізу решіт від ширини повздовжніх перетинок для різних решіт. Це дає можливість візуальної оцінки необхідності збільшення живого перерізу решіт шляхом зменшення ширини повздовжніх перетинок, які їх утворюють. Суттєве зменшення ширини перетинок стає можливим завдяки використання нових матеріалів – плетених шнурів з надвисокомолекулярних поліетиленів типу Spectra/Dyneema, що забезпечують високі показники механічної міцності і зносостійкості при «абсолютній» нерозтяжності. The article presents considerations for creating conditions for the intensification of the process of grain separation by geometric features. The review of constructions and the analysis of work of known sieve surfaces from a position of possibility of maintenance of high indicators of technological efficiency at the expense of acceleration of orientation of particles concerning sieve apertures is carried out. It is established that the most favorable orientation conditions are provided by the surfaces formed by longitudinal elements of small cross-section of streamlined shape, which minimize the possibility of placing particles on them in positions of stable equilibrium. Theoretical possibilities of increasing the living cross-sectional areas and live cross-sectional coefficients of sieve canvases without cross-sections are revealed. The dependences of the total width of the longitudinal sections and the coefficient of the living cross section of the sieves on the width of the longitudinal sections for different sieves are given. This makes it possible to visually assess the need to increase the living cross section of the sieves by reducing the width of the longitudinal sections that form them. A significant reduction in the width of the partitions is possible due to the use of new materials - braided cords made of ultra-high molecular weight polyethylene type Spectra / Dyneema, which provide high mechanical strength and wear resistance with «absolute» inextensibility. В статье изложены соображения по созданию условий для интенсификации процесса сепарации зерна по геометрическим признакам. Проведен обзор конструкций и анализ работы известных решетных поверхностей с позиции возможности обеспечения высоких показателей технологической эффективности за счет ускорения ориентации частиц относительно отверстий решета. Установлено, что наиболее благоприятные условия ориентации обеспечивают поверхности, образованные продольными элементами малого сечения обтекаемой формы, которые минимизируют возможность расположения на них частиц в положениях устойчивого равновесия. Выявлены теоретические возможности увеличения площади живого сечения и коэффициента живого сечения решетных полотен, которые не имеют поперечных перегородок. Приведены зависимости суммарной ширины продольных перегородок и коэффициента живого сечения решет от ширины продольных перегородок для различных решет. Это дает возможность визуальной оценки необходимости увеличения живого сечения решет путем уменьшения ширины продольных перегородок, которые они образуют. Существенное уменьшение ширины перепонок становится возможным благодаря использованию новых материалов - плетеных шнуров их сверхвысокомолекулярных полиэтиленов типа Spectra/Dyneema, обеспечивающих высокие показатели механической прочности и износостойкости при «абсолютной» неростяжимости.Item Дослідження та порівняльний аналіз зносостійкості литих мелючих тіл з хромистих чавунів(ЦНТУ, 2022) Ломакін, В. М.; Кропівний, В. М.; Пукалов, В. В.; Кропівна, А. В.; Молокост, Л. А.; Lomakin, V.; Kropivnyi, V.; Pukalov, V.; Kropivna, O.; Molokost, L.Випробувано мелючі тіла, відлиті з хромистого чавуну в багатомісному кокілі, на ударно- абразивну зносостійкість і ударостійкість. Для дослідження прийнято три типи хромистих чавунів: низькохромистий (~1% Cr), середньохромистий (до 5% Cr) і високохромистий (ВХБЧ, до 20% Cr). Досліджено макро- і мікроструктуру зазначених сплавів, як матеріалу литих мелючих куль. Встановлено підвищення ударно-абразивної зносостійкості і ударостійкості таких виробів при збільшенні масової частки хрому в чавуні за рахунок утворення в металевій основі карбідів типу (Fe, Cr)3C і особливо (Fe, Cr)7C3. Економічно обґрунтовано в якості матеріалу мелючих куль низькохромистий білий чавун. A study was made of the impact-abrasive wear resistance and impact resistance of grinding bodies cast in a multi-place mold. Three types of chromium cast irons were adopted for the study: low chromium (~1% Cr), medium chromium (up to 5% Cr) and high chromium (up to 20% Cr). The macro- and microstructure of these alloys as a material for cast grinding balls has been studied. Installed an increase in the impact-abrasive wear resistance and impact resistance of such products with an increase in the mass fraction of chromium in cast iron due to the formation of carbides of the (Fe, Cr)3C and especially (Fe, Cr)7C3. Balls were cast in multi-seat chill molds. Cast iron was smelted in a medium-frequency induction furnace, such as IChT, with the main lining on a charge of pure pig iron and steel low-carbon scrap. The temperature of cast iron production was 1500 °C. Liquid cast iron was subjected to alloying with medium carbon ferrochrome. The wear resistance of cast irons was determined on samples cut from balls in the radial direction. The tests were performed in a laboratory mill When tested for impact resistance, the grinding ball received a striking blow of mass 50 kg, falling from a height of 0,5 m. The frequency of application of dynamic loads was 10 beats per minute. Impact resistance was determined by the average number of impacts sustained by the grinding body prior to destruction. Nevertheless, significant excess of the cost high-chromium over low-chromium cast iron forces us to agree with the opinion of the majority of researchers and the practice of production of such metal products. In today's conditions, low-chromium white cast iron is an economically viable material for grinding media.Item Люнет для направлення рушничних свердел(ДП “Український інститут інтелектуальної власності”, 2021) Свяцький, В. В.; Скрипник, О. В.; Молокост, Л. А.; Пух, Є. В.; Гуслістий, В. В.; Sviatskyi, V.; Skrypnyk, O.; Molokost, L.; Pukh, Y.; Huslistyi, V.Люнет для направлення рушничних свердел, у корпусі якого встановлені обертові циліндричні ролики, рухливі в напрямку, перпендикулярному осі свердла під дією механічного зусилля, у зовнішню поверхню яких упираються вершини канавки для виходу стружки, і які мають ширину, трохи більшу діаметра свердла, і нерухливі ролики, що мають профіль, відповідний до профілю свердла, при цьому рухливі і нерухливі ролики розташовані попарно в одній площині уздовж осі свердла, згідно з корисною моделлю рухливі і нерухливі ролики оснащені демпфувальними перекладками. A lunette for directing rifle drills, in the body of which are installed rotating cylindrical rollers, movable in a direction perpendicular to the axis of the drill under the action of mechanical force, against the outer surface of which the tops of the grooves for the exit of chips rest, and which have a width slightly greater than the diameter of the drill, and stationary rollers , having a profile corresponding to the profile of the drill, while the movable and immovable rollers are located in pairs in one plane along the axis of the drill, according to the useful model, the movable and immovable rollers are equipped with damping spacers.Item Порівняльна промислова оцінка графітових родовищ та руд України, характеристика збагачення руд(ЦНТУ, 2019) Кропівний, В. М.; Молокост, Л. А.; Кузик, О. В.; Кропівна, А. В.; Кропивный, В. Н.; Молокост, Л. А.; Кузык, А. В.; Кропивная, А. В.; Kropivnyy, V.; Molokost, L.; Kuzyk, O.; Kropivnaуa, A.В статті розглянуто основні родовища графіту в Україні, методи збагачення графітових руд в залежності від ступеню їх фізико-хімічних змін, зроблено порівняльну промислову оцінку родовищ та визначені найбільш перспективні для освоєння об’єкти. На прикладі трьох найбільших родовищ графіту Українського щита розглянута проблема збагачення графітових руд, а також принципи їх поділу на промислові типи, дана характеристика графітовим рудам і властивостям графіту, застосування графіту в промисловості. Властивості цього мінералу дозволяють використання його, як і вуглецю в цілому, у всіх галузях народного господарства, науки та техніки. Основні галузі застосування природного графіту: - металургія (виробництво тиглів, ливарних форм, вогнетривів, протипригарних фарб); - нафтогазова галузь; - електрохімія; - машинобудування, авіаційна та космічна техніка(гальмівні колодки і накладки, самозмащувальні механічні частини – підшипники і вкладки).Визначені особливості кон'юнктури ринку графіту, що передбачає аналіз динаміки видобутку, виробництва, споживання мінеральної сировини в Україні та світі. В статье рассмотрены основные месторождения графита на Украине, методы обогащения графитовых руд в зависимости от степени их физико-химических изменений, сделана промышленная оценка, определены наиболее перспективные для освоения объекты. На примере трех наибольших месторождений графита Украинского щита рассмотрена проблема обогащения графитовых руд, а также принципы их разделения на промышленные типы, дана характеристика графитовым рудам свойствам графита, применение графита в промышленности. Основные области применения природного графита: - металлургия (производство тиглей, литейных форм, огнеупоров, противопригарные красок) - нефтегазовая отрасль; - електрохимия; - машиностроение, - авиационная и космическая техника (тормозные колодки и накладки, самосмазывающиеся механические части - подшипники и вкладки).Определены особенности коньюктуры рынка графита, что предусматривает анализ динамики добычи, производства, потребления минерального сырья в Украине та мире. In the article the basic deposits of graphite in Ukraine, methods of enrichment of graphite ores depending on degree of their physical and chemical changes are considered, the industrial estimation is made, the most perspective objects for development are defined. On the example of the three largest graphite deposits of the Ukrainian shield, the problem of enrichment of graphite ores, as well as the principles of their separation into industrial types, the characteristic of graphite ores and properties of graphite, the use of graphite in industry are given. The properties of this mineral allow you to use it as and carbon in General, in all sectors of the national economy, science and technology. The main fields of application of natural graphite: - metallurgy (production of crucibles, foundry molds, refractories, anti-stick paints); - oil and gas industry; -electrochemistry; -engineering, aviation and space technology (brake pads and pads, self-lubricating mechanical parts - bearings and pads). Peculiarities of graphite market conjuncture are determined that provides analysis of dynamics of extraction, production, consumption of mineral raw materials in Ukraine and in the world.Item Пристрій для закріплення заготовок(ДП “Український інститут інтелектуальної власності”, 2021) Свяцький, В. В.; Скрипник, О. В.; Молокост, Л. А.; Черніченко, К. С.; Казимірко, Н. В.; Sviatskyi, V.; Skrypnyk, O.; Molokost, L.; Chernichenko, K.; Kazymirko, N.Пристрій для закріплення заготовок, на корпусі якого розміщена центрувальна гофрована втулка, призначена для взаємодії за допомогою кільця з гайкою, з'єднаною із тягою. З метою спрощення і здешевлення виготовлення пристрою, центрувальна гофрована втулка виконана набірною із тарілчастих пружин. A device for fixing workpieces, on the body of which there is a centering corrugated sleeve, designed to interact with a nut connected to a rod by means of a ring. In order to simplify and reduce the cost of manufacturing the device, the centering corrugated sleeve is made of plate springs.Item Система технологій. Практичні роботи(ЦНТУ, 2024) Кузик, О. В.; Кропівний, В. М.; Кропівна, А. В.; Молокост, Л. А.; Kuzyk, O.; Kropivnyi, V.; Kropivna, A.; Molokost, L.Основною метою дисципліни покладено вироблення у студентів навичок системного підходу до оцінки технології виготовлення будь-якого виробу на основі відомих початкових даних (кількість та якість продукту, наявність сировини, устаткування, стан технології та сучасних технологічних доробок, вартість устаткування та сировини, екологічна безпека, попит ринку, тощо). The main goal of the discipline is to develop students' skills in a systematic approach to assessing the manufacturing technology of any product based on known initial data (quantity and quality of the product, availability of raw materials, equipment, state of the art and modern technological developments, cost of equipment and raw materials, environmental safety, market demand, etc.).Item Термодинамічна енергоефективність парокомпресійного теплового насоса на грунтових водах(ЦНТУ, 2022) Босий, М. В.; Кропівний, В. М.; Кузик, О. В.; Кропівна, А. В.; Молокост, Л. А.; Bosiy, M.; Kropivnyi, V.; Kuzyk, О.; Kropivna, А.; Molokost, L.В статті розглянуто термодинамічну енергоефективність парокомпресійного теплового насоса (ПКТН) при використанні природних джерел теплової енергії довкілля, зокрема грунтових вод. Представлені схема ПКТН «вода-вода» для системи теплопостачання, температурні рівні в загальній системі ПКТН «вода-вода» та наведено приклад роботи циклу ПКТН «вода-вода» в р-h діаграмі для пропана (R290). Приведено результати термодинамічного дослідження енергоефективності застосування ПКТН при використанні грунтових вод як джерела низькопотенційної теплової енергії. Розглянуто застосування чистих вуглеводнів як робочих речовин для ПКТН, а також метод оцінки енергоефективності за ексергетичним аналізом термодинамічних процесів перетворення енергії, що відбуваються в ПКТН, робочим тілом якого є холодильний агент R290. Енергетичну ефективність ПКТН оцінювали коефіцієнтом перетворення ТН COP, він за розрахунками дорівнює 4,5. Термодинамічну ефективність ПКТН в системах теплопостачання розглядали за допомогою ексергетичного ККД в залежності від середньотермодинамічних температур теплоносіїв в конденсаторі і випарнику, який характеризує досконалість перетворення енергії і становить 44 %. The thermodynamic energy efficiency of a steam compression heat pump (PKTN) using natural sources of environmental heat, in particular groundwater, is considered in the article. The scheme of PKTN "water-water" for the heat supply system, temperature levels in the general system of PKTN "water-water" are presented and the example of work of the PKTN "water-water" cycle in the p-h diagram for propane (R290) is given. The results of a thermodynamic study of the energy efficiency of the use of PKTN when using groundwater as a source of low-potential thermal energy are presented. The article considers the use of pure hydrocarbons as working substances for PKTN, as well as a method for assessing energy efficiency by exergy analysis of thermodynamic energy conversion processes occurring in PKTN, the working fluid of which is the refrigerant R290. The energy efficiency of PКTN was estimated by the conversion coefficient of TH COP, it is calculated to be 4.5. The thermodynamic efficiency of PKTN in heat supply systems was considered using exergy efficiency depending on the average thermodynamic temperatures of heat carriers in the condenser and evaporator, which characterizes the perfection of energy conversion and is 44%. A thermodynamic study of the effectiveness of PKTN "water-water" for the space heating system using groundwater as a source of low-potential thermal energy. Evaluation of energy efficiency of thermodynamic processes of energy conversion occurring in PKTN "water-water" whose working fluid is a refrigerant R290 (propane) is performed by the method of exergetic analysis. It is shown that the exergetic efficiency of PKTN "water-water" depending on the average thermodynamic temperatures of evaporation and condensation is 44%.Item Технічне та технологічне забезпечення краплинного зрошення овочевих культур(ЦНТУ, 2020) Васильковська, К. В.; Ковальов, М. М.; Молокост, Л. А.; Vasylkovska, K.; Kovalov, M.; Molokost, L.; Васильковская, К. В.; Ковалев, Н. Н.В статті запропоновано схему краплинного зрошення для вирощування овочевих культур на присадибній ділянці. Проведена серія досліджень із забезпечення вологою ділянки та збереження повітрообміну ґрунту. Запропоновано розрахунок та схему краплинного зрошення стрічкового типу. В запропонованій конструкції для краплинного зрошення ділянки під овочеві культури використано ємність з водою для забезпечення невеликого постійного тиску води в стрічках. Це дало змогу здійснювати полив за необхідністю, а також використовувати ємність для розчину для підживлення рослин, захисту їх від стресів, покращення розвитку та збільшення врожайності. Використання краплинного зрощення дало змогу з’явитись першим плодам на декаду раніше та збільшити врожайність на 25-50%. The article proposes a scheme of drip irrigation for growing vegetables in the backyard. In the conditions of change of climatic conditions, the question of lack of moisture sharply arises. For growing vegetables in areas of risky agriculture, irrigation is an important condition for obtaining high yields. In order to increase the technological efficiency of growing vegetables at the department of general agriculture of the Central Ukrainian National Technical University developed a prototype of a drip irrigation system for vegetables. A series of studies was conducted to provide moisture to the site and preserve soil air exchange. With the use of conventional irrigation, possible negative consequences in the form of soil flooding, the root system of plants is not able to develop evenly and is deficient in oxygen. The calculation and the scheme of drip irrigation of tape type are offered. In the proposed design for drip irrigation of the area under vegetable crops used a container with water to provide a small constant water pressure in the strips. This made it possible to water as needed, as well as to use a solution tank to feed the plants, protect them from stress, improve development and increase yields. The use of drip splicing allowed the first fruits to appear a decade earlier and increase yields by 25-50%. The use of drip tape irrigation system on the experimental plots allowed to increase the quantity and quality of tomato harvest. Also, the use of drip irrigation allowed to maintain the optimal water-physical regime in the root layer of the soil, which created the conditions for a better harvest. Thus, with the change of climatic situation, most of the Kirovohrad region was looking for in the zone of risky agriculture. Drip irrigation has an almost universal application, is effective in intensive technologies for growing crops and ornamental crops, as well as in garden areas, when the condition of the plant largely depends on the accuracy of maintaining the humidity and nutrition of plants. В статье предложена схема капельного орошения для выращивания овощных культур на приусадебном участке. Проведена серия исследований по обеспечению влагой участка и сохранения воздухообмена почвы. Предложено расчет и схему капельного орошения ленточного типа. В предлагаемой конструкции для капельного орошения участка под овощные культуры использовано емкость с водой для обеспечения небольшого постоянного давления воды в лентах. Это позволило осуществлять полив при необходимости, а также использовать емкость для приготовления раствора для подкормки растений, защиты их от стрессов, улучшения развития и увеличения урожайности. Использование капельного орошения позволило появиться первым плодам на декаду раньше и увеличить урожайность на 25-50%.Item Ударостійкий чавун для молольних тіл(ЦНТУ, 2020) Ломакін, В. М.; Молокост, Л. А.; Lomakin, V.; Molokost, L.; Ломакин, В. Н.Проведено дослідження динамічної міцності (ударостійкості) молольних тіл, відлитих з низькохромистого чавуну в багатомісному кокілі, в залежності від вмісту хрому в сплаві. Встановлено підвищення ударостійкості виливків куль при збільшенні масової частки хрому в чавуні в межах до 1%. При цьому найбільше зростання динамічної міцності спостерігається при збільшенні масової частки хрому від 0,3% до 0,5%. При подальшому зростанні вмісту хрому ударостійкість білого низьколегованого чавуну підвищується менш помітно і при вмісту хрому 0,7-0,8% досягає максимуму. A study of the dynamic strength (impact resistance) of grinding bodies cast from low-chromium cast iron in a multi-seat chill mold depending on the chromium content in the alloy is carried out. As a starting point, cast iron of the following composition was used: carbon – 3,0%, silicon – 1,6%, manganese – 0,4%, sulfur – 0,05%, phosphorus – 0,06%. For the study, several batches of balls with a diameter of 60 mm were cast with different chromium content in cast iron, from 0 to 1%. Cast iron was smelted in a mediumfrequency induction furnace, such as IChT, with the main lining on a charge of pure pig iron and steel low-carbon scrap. The temperature of cast iron production was 1500 °C. Liquid cast iron was subjected to alloying with medium carbon ferrochrome. Balls were cast in multi-seat chill molds. When tested for impact resistance, the grinding ball received a striking blow of mass 50 kg, falling from a height of 0,5 m. The frequency of application of dynamic loads was 10 beats per minute. Impact resistance was determined by the average number of impacts sustained by the grinding body prior to destruction. An increase in the impact resistance of ball castings has been established with an increase in the mass fraction of chromium in cast iron up to 1%. Moreover, the greatest increase in dynamic strength is observed with an increase in the mass fraction of chromium from 0,3% to 0,5%. With a further increase in the chromium content, the impact resistance of white low-alloy cast iron increases less noticeably, and in the presence of chromium 0,7-0,8% reaches a maximum. The difference in hardness from the surface (~ 52 HRC) to the center of the ball (~ 42 HRC) is a value of about 10 units. The established impact resistance of grinding bodies made it possible to conclude: when grinding solid rocks with high content of solid quartz, the use of low chromium cast iron as a material for grinding media is the most effective, as in terms of achieve high impact resistance, and to ensure cost-effective performance. Проведено исследование динамической прочности (ударостойкости) мелющих тел, отлитых из низкохромистого чугуна в многоместном кокиле, в зависимости от содержания хрома в сплаве. Установлено повышение ударостойкости отливок шаров при увеличении массовой доли хрома в чугуне в пределах до 1%. При этом наибольший рост динамической прочности наблюдается при увеличении массовой доли хрома от 0,3% до 0,5%. При дальнейшем росте содержания хрома ударостойкость белого низколегированного чугуна повышается менее заметно, и при наличии хрома 0,7-0,8% достигает максимума.