Конструювання, виробництво та експлуатація сільськогосподарських машин. Випуск 45. Ч. 2 - 2015
Permanent URI for this collectionhttps://dspace.kntu.kr.ua/handle/123456789/2009
Browse
Item Експериментальні дослідження процесу транспортування зернового матеріалу шнеком(КНТУ, 2015) Куликівський, В. Л.; Палійчук, В. К.; Боровський, В. М.; Kulykivskyi, Vladimir; Palіychuk, Vladimir; Borovskyi, VictorНаведена методика та результати експериментальних досліджень ефективності роботи гвинтових робочих органів транспортерів. Представлені стенди для проведення досліджень зі встановленими на них необхідними пристроями, механізмами і приладами для зміни, регулювання та вимірювання конструктивно-кінематичних параметрів гвинтових транспортерів. Визначені критерії оптимізації, а також фактори, що впливають на них. Experimental studies of the transportation of grain materials screw working body carried out in order to create an effective and reliable design of the screw. The method and results of experimental studies the effectiveness of the work of screw conveyors. The stands for research fitted with the necessary devices, mechanisms and instruments for change, management and measurement of structural and kinematic parameters of screw conveyors. Well the criteria of optimization as the factors influencing them. To study the effect of vibration elements screw feeder to transport efficiency. Experiments with vibration screw feeder found in all cases, a decrease in the circulation of the transported material, increasing the productivity of the screw.Item Вплив розрідження на ймовірність появи пропусків та двійників при дозуванні насіння пневмомеханічним висівним апаратом(КНТУ, 2015) Бойко, А. І.; Попик, П. С.; Банний, О. О.; Bojko, Anatoliy; Popyk, Pavlo; Bannyi, OleksandrВ статті представлено результати експериментальних досліджень по встановленню впливу ступеня розрідження у вакуумній камері на появу пропусків та двійників при висіві насіння пневмомеханічним висівним апаратом, оснащеним комірками з направленим вектором дії. The aim is research of influence of the degree of liquefaction in a vacuum chamber to the emergence of omissions and doubles when dosing device with pneumomechanical seed doser directed action. Found that in the range of operating speeds (V = 0,2...0,6 m/s) reduces the likelihood of increase in liquefaction omissions several times. This indicates that apart forms seeds an important role in suction and transportation plays density material (seed weight) which affects the distribution effort in delighted her cell. Increased liquefaction contributes to the formation doubles, the number of which depends also on the shape of and density of seeds fit them to the cell. When increasing liquefaction increases probability of occurrence of doubles. At that, this dependencies is typical to all cultures. Dependencies are nonlinear character with the gradual increase of the likelihood doubles at rising liquefaction.Item Стохастичне моделювання триботехнічних деградовних процесів та прогнозування показників надійності(КНТУ, 2015) Гринченко, О. С.; Алфьоров, О. І.; Grynchenko, Oleksandr; Alferov, OlexsyiВикладено метод стохастичного моделювання процесів накопичення механічних пошкоджень в елементах машин і прогнозування на цій основі показників механічної надійності. Providing focused on improving the reliability of transport equipment Ukrainian production design requires extensive use of simulation techniques and forecasting reliability. The article is an exposition of the method of stochastic modeling of processes of accumulation of mechanical damage in the elements of machines and forecasting based on this performance mechanical reliability. Feasibility reliability prediction requires data on the value of input parameters, statistical evaluation that can be performed through the use of discrete data with continuous monotonic random process. The practical significance of this method of modeling and forecasting of mechanical reliability for the design phase and tests of prototypes is built on the basis of the real statistics object model reliability will reflect the whole range of operational impacts and factors affecting the degradation processes and resource allocation.Item Удосконалення начіпного агрегату для обробітку грунту на похилих полях(КНТУ, 2015) Поляков, А. М.; Polyakov, А.На основі проведеного аналізу якісних показників обробітку грунту на похилих полях запропонований удосконалений начіпний агрегат, який забезпечує стійкість прямолінійного руху ґрунтообробного знаряддя під час роботи поперек схилу. The aim of the revision is mounted tractor to keep the tiller in the straight direction, regardless of operating conditions to eliminate the possibility of damage to crops. Analysis of the units with serial mounted system has shown that they do not provide high quality tillage work on sloping fields [2,3], as in the gun, such as cultivators, there is a lateral force that is trying to remove him from the rectilinear motion in the direction of the slope [4]. At the same time possible damage to plants cultivated cultivator unacceptable. To preserve the straightness of motion machine when working on slopes, the hinged system the tractor should be equipped with an additional thrust to the location of its rear hinge on the same shaft with the upper rod to form a closed triangle. Hold in rectilinear motion tractor mounted implement in the performance of tillage works on a sloping field can be achieved by a hinge extra traction on the upper axis of the tractor and adjusting devices other rod linkage by changing their length, with the result that the working bodies of the cultivator will not damage the cultural plants.Item Технико-экономическое обоснование и анализ перспектив точного посева зерновых культур пневмоструйными аппаратами(КНТУ, 2015) Аулин, В. В.; Панков, А. А.; Аулін, В. В.; Панков, А. О.; Aulin, Victor; Pankov, AndrejВ статье рассмотрены перспективы развития и применения технических средств для точного посева семян рядовых зерновых культур, в частности на основе элементов пневмоструйной техники. Проведены экспериментальные исследования траектории полёта семян на выходе из пневмоструйного аппарата с высевающим барабаном. У статті розглянуто перспективи розвитку та застосування технічних засобів для точного висіву насіння рядових зернових культур, зокрема на основі елементів пневмоструминної техніки. Проведено експериментальні дослідження траєкторії польоту насіння на виході з пневмоструминного апарату з висівним барабаном. The aim of the research is to find new technical means to implement precise seeding of ordinary crops, in particular through the application of pneumotropic elements and devices. As a result of techno-economic analysis identified benefits and feasibility of implementing precision planting of seeds of grain crops. From the review of patent and licensing records indicate that the implementation of precision planting of cereal seeds are the most promising drum pneumatic sowing machines. Therefore, this article discusses experimental studies of the trajectory of the seed at the exit of fluidsmashine unit with metering drum. To reduce energy consumption and improve reliability and performance exact seeding of cereal crops is a promising application pneumotropic sowing machines and systems.Item Анализ и прогнозирование механической надежности сельскохозяйственных культиваторов(КНТУ, 2015) Гринченко, А. С.; Алферов, А. И.; Юрьева, А. П.; Гринченко, О. С.; Алфьоров, О. І.; Юр'єва, Г. П.; Grynchenko, Oleksandr; Alferov, Olexsyi; Yirueva, GannaВ статье рассмотрены вопросы прогнозирования и обеспечения надежности сельскохозяйственных культиваторов при возникновении внезапных механических отказов элементов упругих подвесок рабочих органов. При этом учитываются коэффициенты вариации несущей способности и экстремальных нагрузок, ожидаемое число экстремальных нагружений, а также количество упругих элементов в культиваторе. У статті розглянуті питання прогнозування та забезпечення надійності сільськогосподарських культиваторів при виникненні раптових механічних відмов елементів пружних підвісок робочих органів. При цьому враховуються коефіцієнти варіації несучої здатності і екстремальних навантажень, очікуване число екстремальних навантажень, а також кількість пружних елементів в культиваторі. Development and validation of methods to ensure mechanical reliability of the cultivators in case of sudden failures and repeated extreme loading. In the article the questions of prognostication and providing of reliability of agricultural cultivators in case of beginning of sudden mechanical refusals of elements of resilient pendants of working organs are considered. The coefficients of variation of bearing strength and extreme loading, expected number of the extreme loading, and also quantity of resilient elements, in a cultivator are thus taken into account. The revealed regularities of influence of number of working bodies of the cultivator, as well as the level of accidental dispersion multiply the current extreme load on the sufficient magnitude of the safety factor of elastic struts.Item Прогнозування залишкового ресурсу агрегатів та систем транспортних засобів сільськогосподарського виробництва за їх технічним станом(КНТУ, 2015) Аулін, В. В.; Каліч, В. М.; Гриньків, А. В.; Голуб, Д. В.; Aulіn, Viktor; Kalich, Viktor; Grinkіv, Andriy; Golub, DmitryВ статті проаналізовано математичні моделі прогнозування ресурсу агрегатів, систем та транспортного засобу в цілому різних авторів, які працювали в напрямку удосконалення різних стратегій технічної експлуатації транспортних засобів. Дано математичну модель визначення ймовірності знаходження агрегату, систем та транспортного засобу в цілому, в працездатному стані, на основі інтенсивності відмов та відновлення агрегатів і систем транспортного засобу. Запропоновано уточнення розрахунку коефіцієнта технічної готовності та використання парку машин. In this article the opportunity to go to the adaptive maintenance strategy, which involves forecasting resource units and vehicles. Defining resource based on diagnostic information of special importance different parameters. The aim is to study and determine remaining resources units and vehicle-based diagnostic information. The first task of which was decided in the article is the analysis methods of forecasting technical condition of units and vehicles. Based on the analysis it was established possibility of determining the residual life of components and vehicles. The models is uptime due run at different stages of the life cycle. Retrieved generalized differential equation of the probability of working condition and given its solution. The expressions for the remaining resources in the different stages of the life cycle of machines, systems and TK in general and with specific technical actions. Included by the probability of the units, systems, vehicle generally operable, when assessing the technical readiness coefficient park and use machines.Item Дослідження модернізованої секції сівалки для прямої сівби зернових культур з одночасним внесенням рідких добрив(КНТУ, 2015) Свірень, М. О.; Амосов, В. В.; Кісільов, Р. В.; Орищенко, С. Б.; Козловський, С. М.; Sviren, Mykola; Amosov, Vladymyr; Kysylov, Ruslan; Oryschenko, Serhiy; Kozlovsky, SerhiyМодернізовано конструкцію та проведено експериментальні дослідження секції для прямої сівби зернових культур з локальним внесенням рідких добрив. Пристосування для внесення рідких добрив дозволяє здійснити цю операцію одночасно з сівбою на глибину, що на 10–20 мм перевищує глибину розташування насіння. Воно працездатне (випадків забивання грунтом не спостерігалося) і якісно виконує свої функції. Sowing in untreated soil significantly reduced the cost of fuel, labor costs, improve the soil, reduce production costs. Seed Terranova Argentine company Bertini, implementing this technology need to be adapted to the soil and climatic conditions of Kirovograd region. The study is used to improve direct sowing cereal crops by setting device for application of liquid fertilizer. The device consists of anchor opener, tubes for feeding liquid fertilizer and leverage opener anchor for attaching to the body section. Experimental study used a laboratory soil Channel Agricultural Engineering Department of the Kirovohrad National Technical University. As basic design used self-propelled trolley soil channel. It installed capacity simulator liquid fertilizers, pump, pipe system, the capacity of seed, fluted feed and electric. The depth location of liquid fertilizers and seeds defined layered device for removing soil. Determined that the device for application of liquid fertilizer allows this operation simultaneously with planting to a depth that exceeds the depth of 10-20 mm seed location. It operable (soil Pile cases were observed) and efficiently performs its function.Item Экспериментальные исследования процесса измельчения грубых и стебельчатых кормов измельчителем с комбинированными ножами(2015) Брагинец, Н. В.; Вертий, А. А.; Брагинець, М. В.; Вертій, О. А.; Braginets, Nikolai; Vertiy, OleksandrПредложена методика экспериментальных исследований процесса измельчения грубых и стебельчатых кормов измельчителем, рабочий орган которого оснащён свободно подвешенными комбинированными ножами, включающими вертикальные клиновидные и поперечные серповидные лезвия, позволяющие создавать необходимые упругие и пластические деформации измельчаемого материала. Запропоновано методику експериментальних досліджень процесу подрібнення грубих і стеблинних кормів подрібнювачем, робочий орган якого оснащений вільно підвішеними комбінованими ножами, що включають вертикальні клиновидні і поперечні серповидні леза, якi дозволяють створювати необхідні пружні і пластичні деформації подрібнювального матеріалу. The technique of experimental studies of the process of grinding the chopper roughage working body which is equipped with a freely suspended combi blades, including vertical and transverse wedge-shaped crescent-shaped blade, allowing to create the necessary elastic and plastic deformation of the crushed material.Item Вплив ґрунту на леза робочих органів ґрунтообробних машин(КНТУ, 2015) Дудніков, А. А.; Келемеш, А. О.; Пасюта, А. Г.; Dudnikov, Anatoly; Kelemesh, Anton; Pasyuta, AndriyНаведено аналіз впливу ґрунту на ріжучі елементи робочих органів ґрунтообробних машин та розглянуто фактори, що забезпечують зниження навантажень. The article describes the main aspects of uneven wear of the blade working bodies of tillage machines. The main goal of the research is to outline the reasons that affect a higher intensity of top wear of the cutting element. Their analysis revealed the formation of compacted soil volume and its impact on the character wear top and bottom faces of the blade cultivating working body plows, cultivators, harrows difficult. Presented justification uneven wear of the front and rear faces of the blade, it is shown that under the back edge of ground friction on steel largely replaced by friction against the ground soil, which causes an increase in the coefficient of friction. The research results can be used to improve the quality of tillage, to reduce the traction effort, to increase operational stability of working bodies of tillage machines.Item The main directions of improving technical level of gear pumps of agricultural machines(КНТУ, 2015) Chernovol, Mikhailo; Kuleshkov, Yuri; Rudenko, Timofey; Krasota, Мikhailo; Черновол, М. І.; Кулєшков, Ю. В.; Руденко, Т. В.; Красота, М. В.The paper presents ways to improve the design of gear pumps and hydraulic drives of modern agricultural machines. The main trends in the increase of technical level of gear pumps are: increase of pressure of hydraulic fluid which is developed by the pump, increase of specific useful capacity, volume efficiency, relief of bearings and decrease of pulsation of instant feed and noise level. Метою роботи було, ґрунтуючись на досвіді проектування шестеренних насосів, визначити основні напрямки розвитку їх конструкцій для подальшого підвищення технічного рівня сільськогосподарської техніки. В процесі досліджень застосовувався критичний аналіз досвіду теоретичних, експериментальних і конструкторських розробок шестеренних насосів сільськогосподарської техніки. Було встановлено, що основними напрямками удосконалення шестеренного насоса є наступні: підвищення тиску робочої рідини, що розвивається насосом, - за рахунок підвищення внутрішнього гідравлічного опору в конструкції шестеренного насоса; підвищення питомого робочого об'єму і потужності - шляхом оптимізації параметрів зубчатого зачеплення і усього вузла, що качає, вцілому, а також за рахунок розвантаження підшипників насоса, що дозволить зменшити габарити, як вузла, що качає, так і насоса вцілому; підвищення коефіцієнта подачі - за рахунок підвищення внутрішнього гідроопору, а також підвищення частоти обертання насоса; зниження пульсації миттєвої подачі і тиску – за рахунок встановлення того, що пульсація подачі і тиску не є неминучим недоліком, пов'язаним з конструктивними особливостями шестеренного насоса, що визначило подальший розвиток конструкції насоса в цьому напрямку шляхом усунення причин виникнення пульсації; зниження шуму в процесі роботи насоса – комплексне багатовимірне завдання, вирішення якого приведе не лише до усунення шуму, але і до істотного підвищення технічного рівня шестеренних насосів сільськогосподарської техніки. Таким чином, були запропоновані основні напрямки подальшого розвитку шестеренних насосів сільськогосподарської техніки, що дозволяють при мінімальних витратах, в рамках традиційних конструкторських схем істотно підвищити технічний рівень шестеренних насосів сільськогосподарської техніки.Item Дисковий універсальний подрібнювач-розподілювач стебел рослин з регульованою шириною смуги розподілення подрібнених частинок(КНТУ, 2015) Говоров, О. Ф.; Govorov, OleksandrОбґрунтована технологічно-конструкційна схема універсального дискового подрібнювача-розподілювача усіх видів сільськогосподарських культур і пожнивних залишків, в тому числі і соломи із валків згідно з агротехнічними вимогами, котрий забезпечує регулювання ширини смуги розділення частинок подрібненої соломи із валків, в залежності від ширини захвату жатки комбайна, яким утворені валки. Sound technological - constructive scheme of universal disk grinder-distributor of all kinds of crops and crop residues, including stubble and straw from the roll according to the agro-technical requirements. Which provides control of the bandwidth of the particle distribution of chopped straw from the rolls, depending on the width Harvesters Combines, formed the rolls.Item Механізація захисту рослин у системі природного землеробства(КНТУ, 2015) Кобець, А. С.; Кобець, О. М.; Кузьменко, О. Ф.; Коbets, Аnatoliy; Коbets, Aleksandr; Кuzmenko, AleksandrВ роботі наведений аналіз основних заходів і методів по захисту рослин у системі природного землеробства, обґрунтована ключова роль біометода захисту рослин. Представлені машинні технології розселення ентомофагів для умов України, їх перспективи розвитку. The article presents analysis of the main actions and methods of crop protection for organic farming. Biological methods of of plant protection play a key role in the making ecologically clean products. The study of existing types of dosing (volume, weight, pneumatic mechanical and pneumatic) has shown that the best dosing for the pupae of Trichogramma is a pneumatic hopper-doser with intermittent supply airflow. Machine technology of entomophages resettlement are promising technologies for the conditions of Ukraine and recommended for widespread use in the system of natural farming. Using the machine systems with low-volume and ultralow-volume spraying technologies increase the efficiency of biological preparations.Item Мінімізація тривалості перебігу перехідних процесів роторної машини на пружно-в’язких опорах з одним автобалансиром(КНТУ, 2015) Гончаров, В. В.; Honcharov, ValeryДосліджено тривалість перебігу перехідних процесів в роторній машині, в якій ротор поміщений з можливістю обертатися навколо власної поздовжньої осі в корпус на пружно-в’язких опорах і зрівноважується статично одним автобалансиром з багатьма корегувальними вантажами. Показано, що тривалість перебігу перехідних процесів: а) залежить від семи безрозмірних параметрів; б) зменшується при збільшенні маси корегувальних вантажів та значному збільшенні: - видовженності складеного ротора (на великих швидкостях обертання); - жорсткості опор корпуса для довгого (на великих швидкостях обертання) і короткого (на малих швидкостях обертання) складеного ротора; - швидкості обертання для довгого і дуже короткого складеного ротора; в) суттєво зменшується при наближенні швидкості обертання ротора до його резонансної швидкості за рахунок безпосереднього зменшення швидкості обертання або – збільшення резонансної швидкості через збільшення видовженності складеного ротора чи жорсткості його опор; г) зменшується при: значному віддалені точки підвісу від центра мас ротора або наближенні безпосередньо до нього для довгого и сферичного (на малих швидкостях обертання) складеного ротора; при наближенні точки підвісу до свого екстремального значення для короткого и сферичного (на великих швидкостях обертання) складеного ротора. Passive auto-balancers are used at balancing of many rotary machines. The investigations of transition processes upon the occurrence of auto-balancing of rotating machines with auto-balancers are absent practically at the moment. In this work analytically investigated the duration of the flow of the transition processes upon the occurrence of auto-balancing in rotor machine in which the rotor is placed with the possibility to rotate around its longitudinal axis in a corps on viscoelastic supports and statically balanced by one auto-balancer with many corrective weights. It is shown that the duration of the flow of the transition processes: а) depends on seven dimensionless parameters; b) decreases with increasing of mass of corrective weights and with a significant increase: - elongation of the composite rotor (at great speeds of rotation); - of stiffness of supports of the corps for the long (at great speeds of rotation) and short (at low speeds of rotation) of the composite rotor; - of the speed of rotation for long and very short of the composite rotor; c) decreases substantially at approaching of the speed of rotation of the rotor to its resonant speed by directly reduction of the speed of rotation or - increasing of resonant speed by increasing of the elongation of the composite rotor or of stiffness its supports; d) decreases when: a significant removal of a point of suspension of AB from the center mass of the rotor, or approach to it for the long and spherical (at low speeds of rotation) of composite rotor; approximation of the point of suspension to its extreme value for short and spherical (at high speeds of rotation) of composite rotor.Item Оптимальное по быстродействию управление объектом при малых значениях ошибки отклонения(КНТУ, 2015) Смирнов, В. В.; Смирнова, Н. В.; Смірнов, В. В.; Смірнова, Н. В.; Smirnov, Vladimir; Smirnova, NataliyaПриведено описание решения задачи реализации одного закона управления в системе управления оптимальной по быстродействию. При малых отклонениях система управления переходит в режим стабилизации и переключает закон управления с оптимального по быстродействию на ПИД или ПИ. При этом система перестает быть оптимальной по быстродействию. Задача реализации одного оптимального по быстродействию закона управления при любых значениях ошибки отклонения решена путем ведения в структуру системы управления статистического блока и блока управляемого аттенюатора, что позволило изменять значение управляющего воздействия в режиме стабилизации пропорционально значению ошибки отклонения. Наведено опис рішення задачі реалізації одного закону управління в системі управління оптимальної за швидкодією. При малих відхиленнях система управління переходить в режим стабілізації і перемикає закон управління з оптимального по швидкодії на ПІД або ПІ. При цьому система перестає бути оптимальною за швидкодією. Завдання реалізації одного оптимального по швидкодії закону управління при будь-яких значеннях помилки відхилення вирішена шляхом ведення в структуру системи управління статистичного блоку і блоку керованого атенюатора, що дозволило змінювати значення керуючого впливу в режимі стабілізації пропорційно значенню помилки відхилення. The description the optimal time management control law implementation problem solving. For small deviations of the control system switches to the stabilization and switches the control law with optimal time in the PID or PI. The system ceases to be the optimal time. The task of implementing one-optimal control law for all values of the error deviation is solved by maintaining the statistical unit and controlled attenuator control system structure, which allowed to change the value of control in the stabilization mode proportional to the error deviation. This decision allowed the control disturbances use without changing the control law system under the influence.Item Електродугове фрезерування(КНТУ, 2015) Боков, В. М.; Bokov, ViktorЗапропоновано та досліджено спосіб електродугового фрезерування, зокрема пазів. Обґрунтовано технологічну схему формоутворення. Отримано математичні моделі технологічних характеристик, які дозволяють керувати процесом та прогнозувати його. The objective of the work is reasoning of technological pattern for shaping grooves by electric arc and prognostication for technological properties of electric-arc milling. The work shows the results of electric-arc groove milling research: - analysis and research of different technological patterns of shaping grooves; - designing of graphite electrode tool of composite structure which ensures working liquid pumping through a narrow parallel-plate duct; - mathematical modeling of technological properties of electric-arc milling. Conclusions. There has been offered a method of cavity working, grooves in particular, by electric-arc milling. There was given experimental reasoning for technological pattern of groove shaping by electric arc with use of graphite electrode tool of composite structure. There have been received mathematical models of technological properties of groove electric-arc milling which enable to control and forecast them.Item Порівняльний аналіз результатів теоретичних й експериментальних досліджень процесу функціонування теплоутилізатора для тваринницьких приміщень(КНТУ, 2015) Алієв, Е. Б.; Яропуд, В. М.; Aliev, Elchin; Yaropud, VitaliyВ статті проведено наочне і статистичне порівняння теоретичних і експериментальних даних, що дало змогу стверджувати про адекватність математичної моделі, яка розроблена в результаті теоретичних досліджень функціонування теплоутилізатора для тваринницьких приміщень і можливість її використання для інженерних розрахунків. The paper conducted a visual and statistical comparison of theoretical and experimental data, which made it possible to argue about the adequacy of the mathematical model, developed as a result of theoretical research unit heat exchanger for livestock buildings and the possibility of its use for engineering calculations.Item Стендові випробування штанг широкозахватного обприскувача(КНТУ, 2015) Паламарчук, П. В.; Гавриленко, М. П.; Сташків, М. Я.; Бортник, І. М.; Palamarchuk, Petro; Gavrylenko, Mykola; Stashkiv, Mykola; Bortnyk, IgorВ статті описано стендові випробування штанг широкозахватного штангового обприскувача виробництва ПАТ «Богуславська сільгосптехніка». Дослідження проведено на стенді для випробування причіпних обприскувачів на динамічні навантаження. У результаті проведених досліджень отримано значення напружень у найбільш небезпечних перетинах елементів штанг обприскувача, значення прискорень та кутових швидкостей секцій штанг. The objective of investigation is experimental studies of stress distribution in the most dangerous sections of elements of barbells of sprayer; determine the size and nature of changes in acceleration and angular velocity of sections barbells of sprayer. The article describes bench tests of barbells of sprayer production of PJSC “Boguslav agricultural machinery”. The study was conducted on the stand for testing trailed sprayers for dynamic loading. As a result of research obtained values of tensions in the most dangerous sections of the elements of barbells of sprayer, meaning acceleration and angular velocity sections of barbells of sprayer. Obtained by conducting bench tests of barbells of sprayer values of stresses in the elements of barbells of sprayer, the size and character of change of acceleration and angular velocity of sections of barbells of sprayer is the basis for simulation modeling in the design of machines for chemical plant protection.Item Результати дослідження агрометеорологічних причин ризику у проектах технологічних систем вирощування сільськогосподарських культур(КНТУ, 2015) Тригуба, А. М.; Луб, П. М.; Шарибура, А. О.; Тryguba, Anatolii; Lub, Pavlo; Sharybura, AndriyУзагальнено результати досліджень впливу агрометеорологічних умов на темпи робіт у проектах технологічних систем вирощування сільськогосподарських культур. Означено вплив агрометеорологічних умов на темпи виконання робіт у проектах технологічних систем із вирощування культурних рослин. Виконано дослідження та узагальнено їх результати щодо впливу агрометеорологічних умов на стан предмету праці. На цій підставі встановлено тривалість проміжків часу, за яких виконання робіт у проектах весняного обробітку ґрунту та сівби, хімічного захисту та збирання врожаю сільськогосподарських культур було можливим. Наведено статистичні характеристики тривалості погожих та непогожих проміжків часу, обґрунтовано їх теоретичний розподіл та представлено диференціальні функції розподілу. Врахування системних особливостей проектів під час обґрунтування управлінських рішень щодо параметрів відповідного технічного оснащення є важливою передумовою підвищення їх ефективності. The researches results of agricultural meteorology terms influence on the rates of works in the technological systems of agricultural plants growing projects are generalized. The influence of agricultural meteorology terms on the rates of works implementation in the technological systems of agricultural plants growing projects is marked. Research is executed and their results are generalized in relation to influence of agricultural meteorology terms on the state of the plants. On that case the duration of time intervals is set for which implementation of works in the projects of spring soil-tillage and sowing, chemical defence and harvesting of plants was possible. The statistical descriptions of duration of fine and inclement intervals of time are brought. The theoretical distribution and the differential functions of distribution are presented. Take into account the system features of projects during the ground of management decisions in relation to the parameters of the corresponding technical rigging is important pre-condition of increase of their efficiency.Item Оцінка трудоємкості агрегатування посівного МТА(КНТУ, 2015) Масалабов, В. М.; Masalabov, VasilНаведено дані оцінки трудоємкості агрегатування посівного МТА, який складається із універсально-просапного трактора тягового класу 1,4, двох причіпних сівалок СЗ-3,6 і нової напівнавісної зчіпки. Експериментально встановлено, що загальна трудоємкість цього процесу становить 0,077 люд.-год. Найбільшу (43%) частку виробничого часу займає від’єднання лівої сівалки та переміщення трактора вправо і вперед разом зі зчіпкою і приєднаною до неї правою посівною машиною. The purpose of this article is to assess the effects scheme of two-machines sowing unit labour input of the alteration of its situation in the workplace and vice versa. The unit consists of a universally-till tractors of drawbar category 1.4, two trailed seeders СЗ-3.6 and the new semi-mounted coupling. Study of retrofitting planting unit of the transport situation in the workplace and vice versa carried out by measuring the stopwatch time for each operation. All measurements during the refurbishment of the unit performed two mechanizers. The process alteration of the unit in the transport situation in the workplace include the following operations: detach the left and moving right tractor seeders; detach the right move left tractor and planter; installing the extension cord coupling of the transport situation in the workplace; adherence to the coupling of seeders. Experimentally determined that total time consuming process of rebuilding two-machines planting unit of the transport situation in the workplace is 0.077 p-h. The largest (43%) part of the production time is to detach the left and moving right tractor seeders and forward along with hitch and attached to the right the planting machine. To reduce non-productive time spent on creating a new unit structure coupling it is advisable to equip the semi-mounted it additional hydraulic cylinder. In addition to lifting and lowering the hitch extension it will act as a damper vertical oscillation.