Техніка в сільськогосподарському виробництві, галузеве машинобудування, автоматизація. Випуск 28. - 2015
Permanent URI for this collectionhttps://dspace.kntu.kr.ua/handle/123456789/833
Browse
Item Повышение износостойкости газотермических покрытий из железо-углеродистных сплавов электроконтактной обработкой(КНТУ, 2015) Черновол, М. И.; Ворона, Т. В.; Кожевникова, Е. Е.; Лопата, Л. А.; Черновол, М. І.; Ворона, Т. В.; Кожевнікова, О. Е.; Лопата, Л. А.; Chernovol, Mykhailo; Vorona, Tetiana; Kozhevnikova, Olena; Lopata, LarysaПредложен способ повышения износотойкости газотермических покрытий из железо-углеродистных сплавов электроконтактной обработкой (ЭКО). В основе способа лежит создание и использование фазово-структурных деформационных превращений, которые обеспечивают повышение износостойкости напыленных покрытий и комплексное улучшение их физико-механических и эксплуатационных свойств. Использование комбинации технологии напыления недорогих сталей и их ЭКО открывает широкие возможности в создании износостойких покрытий. Запропоновано спосіб підвищення зносостійкості газотермічних покриттів з залізо-вуглецевих сплавів електроконтактною обробкою (ЕКО). В основі методу лежить створення і використання фазово- структурних деформаційних перетворень, які забезпечують підвищення зносостійкості напилених покриттів і комплексне поліпшення їх фізико-механічних та експлуатаційних властивостей. В результаті ЕКО ГПН / ЕДН покриттів із сталей мартенситного і феритного класів у покриттях формується двофазна структура, що містить метастабільний аустеніт, що має твердість 200 - 300 НV, а також певну кількість оксидів. При цьому, в процесі подальшої експлуатації деталей з цими покриттями внаслідок інтенсивної пластичної деформації метастабільний аустеніт буде трансформуватися в зносостійкий і твердий мартенсит (НV = 700 ... 800) за рахунок протікання деформаційного у - α перетворення. Використання комбінації технології. A method for an increase in the wear resistance of iron-carbon alloy coatings using electric contact treatment is proposed, which is based on the initiation and use of phase-structural deformation transformations, which provide an increase in the wear resistance of deposited coatings and complex improvement of their physical-mechanical and performance properties. As a result, in coatings from steels of martensite and ferrite types a two-phase structure has been formed, which contained a metastable austenite with a hardness of 200-300 HV along with some amount of oxides. In the course of operation of parts with such coatings, thanks to intense plastic deformation, the metastable austenite tends to transform into wear-resistant and hard martensite (НV=700...800) due to the y - a deformation transformation.Item Проблеми підвищення експлуатаційної надійності та можливості удосконалення стратегій технічного обслуговування мобільної сільськогосподарської техніки(КНТУ, 2015) Аулін, В. В.; Гриньків, А. В.; Aulin, Viktor; Hrynkiv, AndryПроаналізовано сучасний стан технічного обслуговування мобільної сільськогосподарської техніки (МСГТ) увага зосереджена на транспортних засобах в сільськогосподарському виробництві. З’ясовано передумови переходу з планово-запобіжної стратегії на альтернативні, які забезпечують необхідний рівень експлуатаційної надійності. Сформульовано основні завдання технічної експлуатації, спрямовані на підтримання справного технічного стану МСГТ. Виявлено, що технічна діагностика займає головне місце у встановленні діагнозу і рівня технічно справного стану МСГТ, наведено схему етапів прогнозування її технічного стану. Встановлено, що на базі прогнозної інформації за допомогою діагностики і методів інформаційної теорії стає можливим перехід від планово-запобіжної до адаптивної стратегії, яка найбільше пристосовує до технічний стан МСГТ до умов її функціонування. Така стратегія є гнучкою в управлінні технічним станом МСГТ та забезпечує максимальну роботоздатність МСГТ при мінімальних витратах. Analyzed the modern state of the maintenance service the mobile of agricultural machinery. Attention basically focused on vehicles in agricultural production. It was found prerequisites of transition from plannedpreventive strategies to alternative which provide a given level of operational reliability. This is the first of all adaptive strategy that is based on the monitoring of technical condition diagnostics systems. Formulated tasks of technical operation designed to maintain good technical condition the mobile agricultural machinery. It was found that ensure maximum of operational reliability is a high priority in the technical operation of a modern market economy.For introduction adaptive maintenance strategy must be consider the following: the use of onboard diagnostic systems enables better monitoring of technical condition; Information technologies provide fast calculations of various indicators of diagnostic information, and necessary to consider individual performance technical condition of vehicles. Found that technical diagnostics occupies the main place in establishing the diagnosis and level of good technical condition the mobile agricultural machinery presented circuit of stages forecasting technical condition, the first phase considers retrospection diagnostic information that has been collected to the latest diagnostic, the second stage diagnosis itself that is needed for determining the real parameters of systems and their mechanisms, the third is projected phase generates recommendations for replacement parts or regulation, and determining the residual life. It was established that based on the of predictive information using diagnosis and development of information theory becomes possible transition from a planned to a safety adaptive strategy that adapts to actual technical state the mobile agricultural machinery. At the present stage of technological development, this strategy is flexible in managing the technical condition MAM and provides maximum serviceability of the mobile agricultural machinery at minimum cost resources.Item Вплив автомобільного транспорту на повітряний басейн міста Кіровограда(КНТУ, 2015) Бевз, О. В.; Магопець, С. О.; Матвієнко, О. О.; Bevz, Oleg; Magopec, Sergiy; Matvienko, OlexandrОбґрунтована актуальність проблеми екологічної безпеки автомобільного транспорту, вплив його на довкілля і проаналізовано дві основні транспортні магістралі, які впливають на забруднення атмосферного басейну міста Кіровограда. In this work considered problems of ecological safety of motor transport, influence of him on an environment and it is analyses two basic transport highways which influence on contamination of atmospheric pool of city of Kirovograd. Researches are directed on determination of degree of work-load of a main transport highway of city of Kirovograd and level of extrass on them. Basic directions of decline of level of contamination of environment of city of Kirovograd from a motor transport is organization of rational chart of routes of motion of passenger and freight streams of city.Item Стратегія розвитку виробництва та переробки зерна кукурудзи як шлях вирішення енергетичної незалежності та безпеки України(КНТУ, 2015) Полішкевич, О. Р.; Polishkevich, OlgaУ статті наведені результати досліджень щодо ефективності використання основних сільськогосподарських культур для виробництва біопалива. Виявлено найефективнішу культуру для переробки. Розрахована ефективність переробки кукурудзи на етанол. Обґрунтовано проект будівництва заводу з виробництва біоетанолу. Запропонована стратегія розвитку виробництва та переробки зерна кукурудзи. Досліджений стан та економічна ефективність виробництва кукурудзи при врахуванні конкурентоспроможності, рівня цін та прибутковості галузі. The aim is to conduct research that focus on evaluating the effectiveness of using corn as a feedstock for biofuel production in Ukraine. The article presents the results of studies on the efficiency of plant crops for biofuels. The effective culture for recycling. Calculated efficiency of processing of corn for ethanol. Reasonably project to build a bioethanol plant. Offered strategy of development of production and processing of grain of corn. Investigational state and economic efficiency of production of corn at the account of competitiveness, standard of prices and profitability of industry. At today's fuel prices is clear that for Ukraine to produce ethanol from corn is beneficial for both domestic consumption and for its exports.Item Дослідження мікропрофіля поверхні одержаного вібраційною обробкою фрезами малого діаметра(КНТУ, 2015) Струтинський, В. Б.; Перфілов, І. В.; Strutynsky, Vasil; Perfilov, IvanВикладено результати досліджень мікропрофіля поверхні одержаного фрезерувальною обробкою фрезами малого діаметра на спеціально розробленому обладнанні. Показано, що мікропрофіль включає ділянки з ізольованими екстремумами та ділянки квазіперіодичності із чітко визначеним напрямком мікрорисок. Запропоновано опис мікропрофіля аналітичними залежностями. Для ділянки з ізольованими екстремумами опис мікропрофіля проводиться функціями на основі кривих Гауса. Для ділянок квазіперіодичності рекомендований спектральний аналіз мікропрофіля шляхом подання його у вигляді відрізка ряду Фур’є. Виконано аналіз особливостей мікропрофіля по різним ділянкам. The results of surface microprofile research obtained with the milling cutters of small diameter on a specially designed equipment are presented. It is shown that the microprofile includes the areas with isolated extremes and the areas of quasiperiodicity with a clear focus of microstrips. A microprofile description with analytical dependencies are suggested. For the areas with isolated extremes the description of microprofile functions is carried out based on the Gaussian curves. For areas with quasiperiodicity the spectral analysis of microprofile by submitting it as a segment of a Fourier series is recommended. The analysis of microprofile in different areas is made. The research purpose is to develop methods for assessing the quality parameters of obtained microprofile which was processed with small diameter mills with imposing high vibration on the workpiece. The special equipment for forming the microprofile was developed. Methods for estimating the microprofile parameters in areas with isolated extremes and in areas with quasi-periodic statements and valves were suggested. The analytical description of microprofile with the set of Gaussian curves and segments of Fourier rows based on microprofile spectrum analysis. The microprofile features analysis was made. The conclusion about the microprofile quality parameters obtained with vibration processing with small diameter mills and the methods of this type of microprofile analysis.Item Шляхи вдосконалення пасажирських перевезень транспортом загального користування(КНТУ, 2015) Мороз, М. М.; Moroz, MykolaПроведено аналіз моделей транспортної технології перевезення пасажирів та розроблено заходи з вдосконалення та розвитку транспортної мережі міста Кременчук. Розвиток міських пасажирських перевезень полягає у широкому впровадженні засобів логістики пасажирських перевезень, які передбачають цілеспрямоване вирішення науково-прикладних задач та забезпечують ефективність і якість кінцевих результатів діяльності транспорту загального користування. The purpose of clause to prove the methodical and practical recommendations to improvement of urban Kremenchug passenger transportations. The analysis of transport technology models of the passengers transportations is carried spent and is developed measures on improvement and development of a transport network of Kremenchug. The development of urban passenger transportations consists in wide introduction of means logistic of passenger transportations, which provide the purposeful decision of scientific-applied tasks and provide efficiency and quality of final results of activity of transport of general usage. Proceeding from materials of the carried spent research on a transport Kremenchug network, and also technical condition of a main road network of city is designed the passengers capacity and quantity of vehicles on each route. From study of population demand on trolleybus routes the tendency of preservation passengers capacity is observed, that allows on the nearest prospect to save an existing network without adjustment changes of a transit and functioning of trolleybus routes.Item Ефективність роботи мобільних електрифікованих засобів сільськогосподарського призначення(КНТУ, 2015) Мельник, Р. В.; Melnyk, RomanВ статті приведенні результати попередніх досліджень експериментального зразка електротрактора ХТЗ-2511Е а також встановлено, що на сьогоднішній день набувають широкого розповсюдження електродвигуни вентильного типу для електротранспорту через високий ККД до 95% та можливістю програмування контролера на різну напругу та різні режими роботи. Improving the operational efficiency of mobile power facilities for agricultural through the use of electricity. Analysis of the previous research was based on the study of scientific and technical information in the field of mobile power on electric-battery drive. Found that currently the ventilated electronic motors for electric transport become widespread because of high propulsive efficiency up to 95% and programmable controller for different voltages and different modes of operation. The developed experimental model of elektric traktor HTZ- 2511E which time of work without recharging batteries is up to 5 hours on transport works. Mobile power facilities based on electric-battery drive in agriculture will increase the efficiency of the machine and tractor units in interpreting the application of the system motor in wheel. Considering the strong potential of JSC "Kharkiv Tractor Plant" and the high level of the electricity sector, Ukraine has good conditions for the solution in the short term all technical issues and successful implementation in the production of tractors with electric-battery drive.Item Моделирование задачи выбора запасного аэродрома на базе искусственной нейронной сети(КНТУ, 2015) Артеменко, О. В.; Artemenko, Olga; Артеменко, О. В.В статье рассмотрена задача выбора запасного аэродрома в процессе предполетной подготовки. Проанализированы факторы, влияющие на выбор запасного аэродрома, описана работа модуля автоматизированного выбора запасного аэродрома, а также представлена нейростевая модель выбора запасного аэродрома. В статті розглянута задача вибору запасного аеродрому в процесі передпольотної підготовки. Проаналізовані фактори, які впливають на вибір запасного аеродрому, описана робота модуля автоматизованого вибору запасного аеродрому, а також приведена нейросіткова модель вибору запасного аеродрому. Preflight preparation of the aircraft crew is a basis of safe flight. One of the tasks to be solved during the preflight preparation includes the choice of alternate aerodromes and specification of weather conditions on them. In order to improve the preflight preparation, the aviation develops and implements computer-based systems of preflight information. It is rational to include the module of choosing an alternate aerodrome in such systems. Modern computer-based systems used for preflight planning choose an alternate aerodrome from Airport Data. However, such systems do not always allow to choose rational alternate aerodromes. In addition, they do not analyze weather conditions. So the problem of modeling the choice of an alternate aerodrome is urgent. In order to solve the set task the following was done: factors influencing the choice of an alternate aerodrome were analyzed, the model of choosing an alternate aerodrome based on an artificial neural network (that allows to estimate the aerodrome according to factors) was developed, and stages of operation of the module of the computer-based alternate airdrome choice were described. The module operation consists of 4 stages and allows to more objectively estimate the condition of factors influencing the choice of an alternate aerodrome and choose the most suitable ones.Item Продуктивність та енергоємність процесу гранулювання зерно-стеблової кормосуміші гвинтовим гранулятором(КНТУ, 2015) Братішко, В. В.; Bratishko, VyacheslavВ статті наведено результати експериментальних досліджень впливу конструкційно-режимних параметрів гвинтового гранулятора кормів та фізико-механічних властивостей кормосуміші на критерії продуктивності та питомої енергоємності процесу гранулювання. Було отримано адекватні математичні моделі процесу гранулювання у вигляді поліномів другого порядку, побудовано та проаналізовано відповідні поверхні відгуку та отримано залежність, що дозволяє встановити оптимальні значення коефіцієнту зміни геометричних параметрів гвинта гранулятора за критерієм продуктивності процесу гранулювання. The aim of research was to establish the influence of structural, operational and technological parameters of the work process of screw feed pellet mill on productivity and specific energy of pelleting process. The paper presents the results of experimental researches of structurally-operational parameters screw feed pellet mill and physical properties of forage mixture on optimization criteria. As a result, studies have provided adequate mathematical model in the form of a second order polynomial describing the influence of forage mixture moisture parameters, changes coefficient of the depth of the channel screw pellet mill for its length, pellet mill matrix holes diameter and number of turns of pellet mill screw on productivity and specific energy pelleting process. There have been constructed and analyzed relevant surface responses. It was established that the function has an optimum performance (maximum) for some values of the changes in the depth of the channel screw pellet mill for its length. It was the expression for finding the optimal values of this ratio. The function of specific energy has optima that meet its minimum value. Rational values correspond to factors beyond their variation.Item Selection of a processing medium for the finishing antifriction nonabrasive treatment(КНТУ, 2015) Chernovol, Mykhailo; Shepelenko, Igor; Budar Mohamed, R.F.; Черновол, М. І.; Шепеленко, І. В.; Будар Мохамед, Р. Ф.The article includes the systematized information on processing mediums used for FANT. The role of processing medium components for producing antifriction coatings with the complex of tribotechnical properties has been shown. On the basis of well-known compositions, conditions for coating formation as well as the functional and technological requirements for FANT processing mediums, the procedure has been proposed for developing and choosing the composition of processing medium for laying the coatings by applying FANT method. Метою даної роботи є розробка алгоритму вибору компонентів складу технологічного середовища для ФАБО. Це дозволить із усього різноманіття вибрати найбільш ефективний склад технологічного середовища, тим самим одержати якісні покриття й підвищити продуктивність ФАБО. Для цього в статті систематизовані відомості про технологічні середовища, що використовуються при ФАБО. Показана роль компонентів технологічних середовищ для одержання антифрикційних покриттів із комплексом триботехнічних властивостей. Проаналізовані основні функціональні й технологічні вимоги до технологічних середовищ, що застосовуються при ФАБО, спрямовані на досягнення комплексу триботехнічних властивостей. На основі аналізу відомих складів, умов формування покриттів, а також функціональних і технологічних вимог, що висувають до технологічних середовищ, запропонований порядок розробки й вибору складу технологічного середовища для нанесення покриттів методом ФАБО.Item Розмірна обробка електричною дугою отворів складного контуру(КНТУ, 2015) Носуленко, В. І.; Юр’єв, В. В.; Nosulenko, Viktor; Yuriev, VitalyРозроблено, теоретично та експериментально досліджено і описано технологічні схеми формоутворення розмірної обробки електричної дуги (РОД) листових деталей складного контуру згідно класифікатора та фізико-технологічні характеристики процесу, його гідродинаміка, конструкції електрода-інструмента (ЕІ), як високоефективну альтернативу традиційним технологіям. The article is devoted to the development and improvement in dimensional processing electric arc holes of challenging when pumping circuit through the electrode-tool and the workpiece. In work the analysis of the known methods of processing of complex contour holes and their shortcomings. Substantiated the technological scheme of forming holes of complex contour method dimensional processing electric arc. Were developed the structure of the electrodes and their relative linear wear A method dimensional processing electric arc for processing sheet metal parts of complex contour and electrode-tool, ensuring high quality treatment.Item Вибір компоновки багатокоординатного верстата паралельної структури з ланками змінної довжини(КНТУ, 2015) Кириченко, А. М.; Шелепко, О. В.; Kyrychenko, А.; Shelepko, О.В статті розглянуті сучасні тенденції розвитку верстатів з паралельною структурою у машинобудуванні та металообробці. Проведено дослідження по вибору раціональнішого варіанту компоновки верстата «пентапод» за параметрами робочого простору і жорсткості. The aim of the article is to choose the layout of pentapod parallel kinematic machine after the criteria of workspace and spatial rigidity. Several configurations with different arrangement of joints on a stationary platform are considered. The geometrical method is used to determine the workspace, and spatial rigidity is calculated using machine kinematics. It’s proved that the workspace of each configuration has a complex geometric shape. Workspace volume and shape significantly depend on the arrangement of joints, which also affects the output specifications of the machine and its ability to process certain parts. The conducted analysis made it possible to choose the layout of the machine according to customer requirements on stiffness and workspace.Item Шляхи можливого розв’язання сучасних проблем вітчизняної енергетики за допомогою поновлюваних джерел енергії(КНТУ, 2015) Жесан, Р. В.; Голик, О. П.; Коренецька, Н. Б.; Попок, А. А.; Zhesan, Roman; Golik, Olena; Korenetskaya, Natalia; Popok, AnastasiyaВ статті проаналізовано стан вітчизняної енергетики, її проблеми та перспективи розвитку. Обґрунтовано доцільність більш широкого застосування поновлюваних джерел енергії, зокрема гідравлічної, сонячної, вітрової та геотермальної. The purpose of this article is to analyze the status of national power engineering, with a focus on the most important issues for today, and the development of solutions to these problems by means of greater use of renewable energy sources. Promoted overview of the structure of the energy sector. Identified the key groups of problems: dependence on imported fossil and nuclear fuels; environmental problems that accompany the development of the energy sector; foreign policy and military-technical aspects. Were analyzed by way of perspective increasing the scale of renewable energy sources. It was concluded that the prospects of using hydraulic, solar, wind and geothermal energy.Item Захист ножів ротаційних різальних апаратів від співударяння з предметами високої твердості(КНТУ, 2015) Говоров, О. Ф.; Govorov, OleksandrПриведено аналіз причин пошкодження ножів ротаційних різальних апаратів косарок та подрібнювачів-розподілювачів рослин і їх решток, а також пристроїв, які захищають ножі таких різальних апаратів від співударяння з предметами високої твердості. Такі пристрої автор розділив на два типи – для захисту співударяння ножів з такими предметами великих розмірів шляхом відведення різальних апаратів від цих предметів та співударяння з такими предметами малих розмірів, які відкидаються від ножів, указав переваги і недоліки кожного типу. Analysis remedies rotary knife cutting machines from collisions with objects of high hardness. The analysis divided the author remedies knives into two types - a device for group and individual protection, established the advantages and disadvantages of each type, as well as individual devices of both types, and also noted that the establishment of the machines of group remedies knives significantly hampers their design and increase the cost, as well as to establish the conditions under which it is advisable to use protective equipment knives. Remedies knives should be used extensively in the fields of high hardness clogged objects, in particular for rocky soils.Item Дослідження динаміки деформації руна грубої овечої вовни при розтягуванні(КНТУ, 2015) Алієв, Е. Б.; Лиходід, В. В.; Забудченко, В. М.; Полюсов, В. В.; Aliev, Elchin; Lykhodid, Viktor; Zabudchenko, Viktor; Polusov, VasilyНаведено результати лабораторних досліджень динаміки деформації руна грубої овечої вовни при розтягуванні з урахуванням її технологічних властивостей. Experimentally determine the deformation characteristics runic sheep wool under tension. The results of laboratory studies of the dynamics of deformation of rough sheep wool under tension taking into account its technological properties. Experimentally found that the process of fleece deformation in tension occurs in two stages: the first stage - to stretch fleece maximum pressure Rmax = 17,2-17,7 kPa, where there is the beginning of the gap fibers of the fleece; the second stage - the fleece gap integrity and smooth tension forces decline to zero. Further research will focus on the practical implementation of the results in the design and manufacture of compact felting machines.Item Особливості оцінки результатів регресійного аналізу(КНТУ, 2015) Бакарджиєв, Р. О.; Комаров, А. О.; Bakardzhyev, Roman; Komarov, AndrewНа конкретних прикладах представлено оцінку результатів регресійного аналізу активного повнофакторного експерименту. Із застосуванням статистичних функцій MS Excel проілюстрована оцінка адекватності математичної моделі другого порядку з вибракуваними статистично незначущими коефіцієнтами, визначено працездатність математичної моделі, відповідності різниці (залишків) нулю і нормальному розподілу та їхня автокореляція. Наведені способи дають змогу швидко з високою точністю визначити всі оціночні параметри отриманого рівняння регресії, його придатність для використання як математичної моделі. Abstract: In an example, evaluation of the results of regression analysis of active fullfactor experiment. With the use of MS Excel statistical functions illustrated assessment of the adequacy of the mathematical model of the second order of rejected statistically insignificant coefficients defined performance mathematical model according difference (residual) with zero and normal distribution and their autocorrelation. These methods allow you to quickly accurately identify all evaluation parameters obtained regression equation, its suitability for use as a mathematical model.Item Автоматичне керування неперервно-послідовним індукційним наплавленням(КНТУ, 2015) Бісюк, В. А.; Дідик, О. К.; Рибакова, Л. В.; Bisuk, Viktor; Didyk, Oleksandr; Rybakova, LudmylaРозглянуто технологічні особливості керування процесом неперервно-послідовного індукційного наплавлення зміцнюючи композиційних покриттів на деталі сільськогосподарської техніки. Запропоновано схему апаратного забезпечення програмно-технічного комплексу для автоматичного керування неперервно-послідовним індукційним наплавленням. One of the main directions of engineering is the development and implementation of tools that will improve the life of machine parts. In the agricultural machinery is very acute issue for parts tillage machines (Lemekh, tips plows, field boards, etc.) that are subject to intense friction and wear out quickly. In most modern engineering perspective to improve operational "longevity" is a method of manufacturing bimetallic weld parts with wear resistant coatings. Wear agricultural working bodies are made, usually in large or high volume production. Therefore, methods to strengthen them must meet the requirements of the production: to be highly productive and economically feasible, to provide a specified thickness and durability deposited layer. Software control speed moving parts in the field of the inductor will set the optimal mode of heating surface details will warm up gradually without major changes in temperature within obroblyayemoyi areas and therefore without significant thermal deformation temperature control of the deposited coating will if necessary extend or reduce the length of surfacing that will provide constant and optimal quality coating helps prevent excess energy consumption.Item Підвищення функціональних властивостей гальванічних полімерометалевих покриттів на основі міді при проточному нарощуванні зношених поверхонь(КНТУ, 2015) Солових, Є. К.; Аулін, В. В.; Солових, А. Є.; Катеринич, С. Є.; Solovykh, Yevgen; Aulin, Viktor; Solovyh, Andriy; Katerynych, StanislavВ статті наведені результати досліджень на зносостійкість, тривалість припрацювання спряжених поверхонь, стійкість до схоплювання композиційних гальванічних покриттів, які містять фенілон і дисульфід молібдену, а також оптимальні концентрації полімерних частинок в електроліті – суспензії для формування покриттів з підвищеними фізико-механічними характеристиками. The article contains the results of experiments on the proof to wear, the time of work of conmections, the standibility to prasp of compositional electrolytic coverings, which contains the molybdenum disulphide and phenyl, and the optimal concentration of polymeric particles in electrolyte-suspension to form the improve physical-mechanical characteristics. Undertaken comparative studies of wearproofness of composition electrodeposits on the basis of copper and electrolytic layers of "clean" copper in the conditions of maximum and dry friction. Influence of antifriction particles is studied, at anything their content in coverage on his property. Shown possibility to get plenty of various types of composition electrodeposits compositions of various materials of matrix and dispersible phase with the purposeful change of their properties in obedience to the set external environments.Item Модернізація вузлів обладнання для механічної обробки гільзи циліндрів двигуна на токарних верстатах застарілої конструкці(КНТУ, 2015) Анастасенко, С. М.; Григурко, І. О.; Ошовський, В. Я.; Будуров, В. Л.; Anastasenko, Sergey; Grigyrko, Ivan; Ohsovsrsy, Victor; Bydyrov, VasilyУ статті представлена модернізація токарних верстатів застарілої конструкції з реконструкцією гідрокопіювальних супортів для механічної обробки гільзи циліндра двигуна та улаштування для автоматизованого завантаження, закріплення і зняття заготовок. При конструкторській розробці на заводі можливо враховувати виробничі можливості ремонтних і інструментальних цехів, на котрі покладається задача переобладнання верстатів і ретельного розрахунку економічних показників,які визначають рентабельність реконструкції і степені автоматизації. В більшості випадків при автоматизації верстатів для роботи за замкнутим циклом виготовлення простих деталей можемо рекомендувати пневмомеханічні улаштування, комбінуючи механічний барабанний привід супорту з пневматичними затискними улаштуваннями. In article modernization of lathes of an outdated design with reconstruction of hydrocopy calipers is provided for machining of a cylinder liner of the engine and the device for the automated loading, fastening and removal of preparations. At design development at plant it is possible to consider production capabilities of maintenance and tool shops to which the problem of re-equipment of machines and careful calculation of economic indicators which define profitability of reconstruction and extent of automation is assigned. In many cases at automation of machines for work behind the closed cycle production of simple details is recommended the pneumomechanical devices combining a mechanical drum drive gear of a caliper with air clamping devices. Re-equipment of the machine is reduced to installation of tightening cylinders, to production of mandrels and the rotating spindle of the rear grandma. Cylinders and cranes of steering and shops. Lathe productivity with a hydrocopy caliper and loading organization will increase by 10 times equalizing it with a productivity at manual service, and expenses will pay off approximately in three months.Item Модернізація сівалки для селекційно-насінницької сівби зернових і зернобобових культур(КНТУ, 2015) Горобей, В. П.; Литвиненко, М. А.; Gorobey, Vasiliy; Litvinenko, NikolayУзагальнені результати досліджень щодо застосування енергозберігаючих технологій в виробництві зернових та в дослідницькій роботі. Розглянуто спосіб сівби на селекційно-насінницьких ділянках за допомогою універсального сошникового вузла. Наведено схему модернізації конструкції найбільш поширеної в селекційно-насінницькій практиці сівалки типу СН-16, та основні переваги, які дозволяють розширити її технологічні та якісні можливості. It is summarized research results of using of energosaving technologies in corn production and in scientific-research work. It is examined the sow method on selection plots with the help of universal ploughshare set and made scheme of construction modernizing of the most popular in selection-seed-growing practice seeder of type CH-16 and done fundamental advantages which allow to widen its technological and qualitative possibilities.
- «
- 1 (current)
- 2
- 3
- »