Збірники наукових праць ЦНТУ
Permanent URI for this communityhttps://dspace.kntu.kr.ua/handle/123456789/1
Browse
3 results
Search Results
Item Чисельне дослідження міцності бібетонних армованих балок, що працюють на згин(ЦНТУ, 2023) Романенко, Д. Б.; Romanenko, D.Одним з методів відновлення експлуатаційних якостей залізобетонних згинаних елементів є підсилення їх стиснутої зони. Це підсилення виконується шляхом влаштування надбетонки, зазвичай, із бетону іншого класу, ніж існуючий елемент. У роботі виконано чисельно-теоретичне дослідження положення нульової лінії у залізобетонних балках, виготовлених із бетонів різних класів у розтягнутій та стиснутій частинах поперечного перерізу. One of the methods of restoring the operational qualities of reinforced concrete bent elements is to strengthen their compressed zone. This reinforcement is performed by placing a concrete overlay, usually of a different grade of concrete than the existing element. In existing research publications, reinforcement of reinforced concrete structures with various materials was considered. A comparison of the reinforcement of experimentally tested different beams was made: unreinforced, reinforced with a layer of steel fiber concrete, polymer concrete, reinforced polymer concrete, fine-grained concrete and reinforcement, and others. Compared to unreinforced samples, all reinforcement methods significantly increased the load-bearing capacity. For beams reinforced with a layer of reinforced steel fiber concrete and polymer concrete, the bearing capacity increased by approximately 1.4 times. And in beams reinforced with a layer of reinforced fine-grained concrete, the indicator of the increase in bearing capacity is slightly less - about 1.18.Item До розрахунку зубців прямозубих циліндричних передач на згин(ЦНТУ, 2020) Невдаха, Ю. А.; Дубовик, В. О.; Невдаха, Н. А.; Златопольський, Ф. Й.; Nevdakha, Yu.; Dubovyk, V.; Nevdakha, N.; Zlatopolskiy, F.; Дубовик, В. А.; Златопольский, Ф. И.В роботі аналізуються розрахункові схеми циліндричної прямозубої передачі на згин зубців. Розглядається найбільш поширена розрахункова схема злому зубця, де небезпечний переріз злому зуба відбувається у основі ножки вище кола діаметра западини зубців. На практиці реальний же злом зубця лежить нижче діаметра западини зубців і має опуклу форму перерізу. Для більш точного розрахунку зубців на згин досліджували коефіцієнт форми зубців. В результаті встановлено, що коефіцієнт форми зуба зменшується зі збільшенням кількості зубців. The aim of the work is to improve the calculations of spur cylindrical wheels per bend, due to the fact that the existing formulas do not give the actual value of the maximum stress, and the diagram does not correspond to the real law of stress distribution. In order to obtain satisfactory results, it is more correct to calculate the teeth at the maximum local stress. Combining the coefficients and substantiating the calculated dependence to determine the value of the coefficient of the shape of the tooth under load, applied at any point of the working profile of the tooth, to obtain formulas for the bending strength of the teeth of the gear and wheel. When calculating the bending teeth, the calculation is based on the stresses arising at the base of the tooth, under the load applied at the top of the tooth. Consider first the most common calculation scheme. Dangerous section of the tooth as seen from the plot of total stresses indicates that the maximum normal stress occurs on the non-working side of the tooth - the compression side, however, since fatigue cracks occur at the base of the tooth on the stretching side, the calculation is based on tensile stress on the working side. The hypothesis of non-curvature of flat sections is unfair for short beams of variable cross section, so the total diagram does not correspond to the real law of stress distribution. But at the base of the tooth near the transition curve is the place of stress concentration. The actual dangerous cross-section lies below the cross-section of the depression, this is confirmed by the fact that the fatigue cracks form an angle with the load curve close to straight, and the fracture of the tooth has a convex shape. In this case, it is more correct to calculate the teeth at the maximum local stress. Combining the coefficients obtained a calculated dependence to determine the value of the coefficient of the shape of the tooth under load, applied at any point of the working profile of the tooth. As a result of the study it was found that the coefficient of tooth shape decreases with increasing number of teeth. This result was expected because as the number of teeth increases, the angle between the teeth decreases, and neighboring teeth perceive part of the stress that occurs in the loaded tooth. The formulas for checking the bending strength of gear teeth and wheels are obtained. The above refinement calculations of the teeth on the bend reflect the beneficial effect of improving the accuracy of the manufacture of teeth. В работе анализируются расчетные схемы цилиндрической прямозубой передачи на изгиб зубцов. Рассматривается наиболее распространенная расчетная схема излома зубцов, где опасное сечение излома зубьев происходит в основе ножки выше круга диаметра впадины зубцов. На практике реальный же излом зубьев лежит ниже диаметра впадины зубьев и имеет выпуклую форму сечения. Для более точного расчета зубьев на изгиб исследовали коэффициент формы зубьев. В результате установлено, что коэффициент формы зуба уменьшается с увеличением количества зубьев.Item Розрахунок зубців прямозубих зубчастих коліс на міцність по напруженням згину з врахуванням сучасних методів розрахунку(КНТУ, 2011) Невдаха, Ю. А.; Лушніков, В. М.; Пукалов, В. В.; Невдаха, А. Ю.; Nevdakha, Y.; Loushnicov, V.; Poucalov, V.; Nevdakha, A.Приведений розрахунок зубців прямозубих зубчастих коліс на міцність по місцевим напруженням згину, які дають більш точний результат на відміну від метода розрахунку по номінальним напруженням. In the article the resulted computation of indents of straightindents gear-wheels on durability by local tensions of bend, which give more exact result unlike the method of computation by nominal tension.