Наукові публікації кафедри ЕРМ
Permanent URI for this collection
Browse
Browsing Наукові публікації кафедри ЕРМ by Author "Arifa, W."
Now showing 1 - 3 of 3
Results Per Page
Sort Options
Item Étude de l'état de contrainte du sol et des organes de travail des machines aratoires et leurs effets sur la résistance a la traction(Elewa BioSciences, 2013) Aulin, V.; Arifa, W.; Аулін, В. В.Objectif : La présente étude a été menée dans le but de mettre en évidence l'identification de l'état de contrainte du sol lors du processus d'interaction avec différents organes de travail des machines aratoires (OTMA) à des profondeurs différentes, et leurs impacts sur la résistance à la traction. Méthodologie et résultats : Lors du passage des OTMA, le complexe MIC 400D fixe la valeur de la contrainte dans les endroits du sol où sont disposées les jauges de contrainte. Le dispositif de détermination de la résistance permet d’enregistrer la résistance à la traction des OTMA lors de leur déplacement. Ainsi, les plus grandes contraintes sont observées au voisinage de la pointe du soc (17,5 kPa) et au milieu de la partie coupante (11,5 kPa) pour le soc unilatéral et, dans les zones proches du soc (23,5 kPa) et de la partie inférieure du coutre (15,1 kPa) pour la sous-soleuse. Conclusion et application des résultats : Les zones de concentration de la contrainte maximale du sol sont observées dans les régions voisines de la pointe du soc et au milieu de la partie coupante du soc unilatéral et dans la zone du sol où agissent le soc et le coutre de la sous-soleuse. La localisation de différentes parties des OTMA subissant une forte contrainte lors du travail du sol et la détermination de leur résistance à la traction dont la valeur est fonction de la profondeur de travail vont beaucoup contribuer à la conception des OTMA optimaux ayant une usure et une résistance à la traction moins élevées. Objective: The present study was conducted to highlight the identification of the tensile state of the soil in the process of interaction with various working bodies of ploughing machines (TMAO) at different depths, and the impacts on the tensile strength. Methodology and Results: During the passage of the TMAO, the MIC complex 400D sets the value of the stress in the places where the soil is disposed to strain. The experimental design of the resistance determination allows the recording of the tensile strength of the TMAO when moving. Thus, greater stresses are observed in the vicinity of the coulter tip (17.5 kPa) and the middle of the cutting portion (11.5 kPa) to the coulter and unilateral, in the near zones of the ploughshare (23.5 kPa) and the lower part of the coulter (15.1 kPa) to the subsoiler. Conclusion and application of results: The areas of concentration of the maximum stress in the soil was observed in neighbouring regions of the coulter tip and the middle of the cutting portion of the coulter unilateral and in the area of soil where the ploughshare and the coulter act on the subsoiler. The location of different parts of TMAO under strong stress during tillage and determining their tensile strength whose value is a function of depth work will contribute significantly to the design of optimal TMAO with wear resistance the lower traction.Item Improvements of harrows wear resistance(IJARIT Rescarch Foundatior, 2015) Arifa, W.; Aulin, V.; Shepelenko, I.; Аулін, В. В.; Шепеленко, І. В.Wear is the main reason for the loss of performance of the parts for agricultural machinery. It leads to the degradation of the soil working quality. This work aims to highlight the wear resistance of the harrows discs manufactured, consolidated and sharpened differently. The tests were conducted in the laboratory and the field of the Faculty of Exploitation and Repair of Agricultural Machinery of the State Technical University of Kirovograd (Ukraine) in 2015. The technical equipment consists of devices for consolidation by electric discharge and for measurement the linear wear of discs, a harrow, a sand test bed, a tractor and discs made of different materials and technologies. Some parameterized were collected during the laboratory test each 5 ha and up to 20 ha of operation and in the fields each 30 ha until the time limit of exploitation. The Laboratory tests have shown that after twenty (20) ha of operation, the wear resistance of the experimental discs made of steel 65G and consolidated by electric discharge with simultaneous grinding (sharpening angle of 30°) is 2.95 times higher than the discs in series made of steel 28MnB5. The field experiment gave the following results: According to agro technical requirements, the plowing depth limit of serial discs made of steel 28MnB5 was reached after an operating duration of 120 ha while for experimental discs made of steel 65G and consolidated by electric discharge with simultaneous grinding (sharpening angle of 30 degrees) this duration is of 156 ha. The diameter wear limit of experimental discs was reached after an operating duration of 179 ha against 154 ha for the serial ones. Therefore, the new technology can be applied during the manufacture and / or the repair of the discs.Item Improving of the wear resistance of working parts agricultural machinery by the implementation of the effect of self-sharpening(Science Publishing Corporation, 2016) Aulin, V.; Arifa, W.; Lysenko, S.; Kuzyk, A.; Аулін, В. В.; Лисенко, С. В.; Кузик, О. В.The failure of the cutting elements of farm machinery is due to the blunting of cutting edges (increase of their radius) till the limit values. The most effective method for increasing the wear resistance of farm machinery is the realization of self-sharpening effect of the cutting elements. The testings took place in laboratory and field at the State Technical University of Kirovograd (Ukraine) in 2015. The technical equipment consists of the consolidated farmer plowshares by different methods as well as their samples, devicesfor measuring the wear resistance and thumbprint plowshares. It was determined the resistance to wear, the radius of curvature and the changing coefficient of the blades shape. The self-sharpening process was examined throughout the experiment.The results showed that the consolidated plowshares by the proposed technology (laser welding of the mixture (PS-14-60 + 6% В4С) compared to the traditional technology (volumetric heat treatment) have a blade radius 2.5 times lower, a wear 2.2 to 2.78 times lower and the self-sharpening process of the plowshares has been observed since the beginning of the wear until the time limit operation. The changing shape coefficient was respectively of 0.98 for the consolidated plowshares with alloy PS-14-60 + 6% B4C and 0.82 for those consolidated by volumetric heat treatment.