Конструювання, виробництво та експлуатація сільськогосподарських машин. Випуск 51. - 2021
Permanent URI for this collectionhttps://dspace.kntu.kr.ua/handle/123456789/11876
Browse
Search Results
Item Дослідження впливу схеми розташування ножів котка-подрібнювача на показники якості подрібнення стебел соняшнику(ЦНТУ, 2021) Шейченко, В. О.; Черновол, М. І.; Вольський, В. А.; Коцюбанський, Р. В.; Sheichenko, V.; Chernovol, M.; Volskyi, V.; Kotsiubanskyi, R.Роботу присвячено удосконаленню технологічного процесу подрібнення стебел соняшнику завдяки дослідженню впливу схеми розташування ножів котка-подрібнювача на показники якості подрібнення. Розроблено та виготовлено дослідний зразок котка-подріюнювача, ріжучі ножі у якого розміщено по всій ширині захвату у шаховому порядку з можливістю змінювати кут нахилу до осі обертання барабана в діапазоні 5…20°. Дoслiджено вплив рoзтaшування рiжучoї крoмки пoдрiбнюючoго нoжa кoтка нa пoказники якocті викoнання опeрацiй пoдрібнeння і зaгортaння стeбeл coняшнику. The study of the arrangement of the blades of the roller-grinder on the quality of grinding. It is The work is devoted to the improvement of the technological process of grinding sunflower stalks due to the study of the influence of the arrangement of the blades of the roller-grinder on the quality of grinding. in the range of 5… 20 °. It is noted that under 800 kg by loading the roller with the right location of the chopping knives, the lowest value of mathematical expectations of the distribution of crushed stem particles is set at 18.6 km / h. This value is 14%, 30%, 40% and 20% less than the speed , respectively, 7.45 km/h, 10.08, 13.6, 22 km/h. Exceedance of values of mathematical expectations of distributions of particles of stalks at a roller-shredder with the left scheme of an arrangement of knives over the right, for loading of 800 kg, at all speeds investigated is established. The lowest value of mathematical expectation for the right layout of the knives was set at a speed of 18.6 km / h, and for the left - at a speed of 13.6 km / h. The highest value of the mathematical expectation of the distribution of parts of sunflower stalks at the left location of the knives is set at a speed of 10.08 km/h, and for the right scheme - at a speed of 13.6 km/h. Exceeding the lowest value of mathematical expectation over the highest within one scheme of placement of knives was - on the left 48%, on the right 41%. In the roller with the left location of the cutting edge of the knives, with a load of 600 kg in the range of 51–100 mm, the percentage of crushed particles of sunflower stalks exceeded the corresponding values with a load of 800 kg. At speeds of 10.08 km/h, 13.6, 18.6 and 22 km/h, this excess was 1.9 times, 1.44, 1.96 and 1.99 times, respectively.Item Вплив параметрів барабана для подрібнення рослинних решток на надійність протікання технологічного процесу(ЦНТУ, 2021) Сало, В. М.; Лещенко, С. М.; Богатирьов, Д. В.; Salo, V.; Leshchenko, S.; Bohatyrov, D.В роботі проводиться оцінка параметрів барабана для подрібнення рослинних решток на надійність протікання технологічного процесу. Проаналізовано існуючі конструкції котків- подрібнювачів рослинних решток та обґрунтовано взаємозв’язок окремих конструктивних та технологічних параметрів подрібнювачів на якісні показники їх роботи і можливість забивання міжножового простору. Проведені експериментальні дослідження по оцінці впливу кута розхилу між сусідніми ножами та робочої швидкості агрегату на ймовірність забивання міжножового простору. Доведено, що підвищення швидкості руху подрібнювачів та збільшення кута розхилу між ножами сприяють зменшенню забивання міжножового простору рослинно-ґрунтовою масою навіть при підвищеній вологості. The paper presents the assessment of the parameters of a chopping rotor for shredding plant residues for the reliability of the technological process. The general objective of the work is to substantiate the design and experimental identification of rational parameters of crimp-rollers of plant residues based on the condition of preventing clogging of the inter-knife space with plant-soil mass. The existing designs of crimp-rollers of plant residues are analyzed and the interrelation of certain constructive and technological parameters of shredders on qualitative indicators of their operation and possibility of clogging of inter-knife space is substantiated. The design of a large diameter crimp-roller provides simultaneous full contact with soil of two and sometimes three knives, which during the operation of the roller, together with cutting stems, provides them clamping with soil particles between adjacent knives. The probability of clogging between knives with plant and soil mass increases sharply with the humidity level of the material. Experimental studies have been conducted to assess the effect of the angle of inclination between adjacent knives and the operating velocity of the unit on the probability of clogging the inter-knife space. It is proved that increasing the speed of the shredders and increasing the decay angle between the knives help to reduce clogging of the inter-knife space with plant-soil mass, even at high humidity. The introduction of technological processes of effective preparation of plant residues in the production of crop products will allow starting the system of soil conservation at a farm. It is most expedient to grind plant residues with driveless roller shredders, the main operating parts of which are rollers with knives mounted on the cylinder, and depending on the purpose, quantity and type of plant residues, rollers with large and small diameters are practically used. When shredding high-stem plant residues, it is recommended to use crimp-rollers of large diameter with the following parameters: speed of the unit is 7…8 m/s, the decay angle between adjacent knives is 42… 46º. These parameters of the crimp-roller of plant residues reduce the probability of clogging the inter-knife space to 8%.