Конструювання, виробництво та експлуатація сільськогосподарських машин. Випуск 51. - 2021
Permanent URI for this collectionhttps://dspace.kntu.kr.ua/handle/123456789/11876
Browse
Search Results
Item Аналіз комп'ютерних систем візуалізації з метою алгоритмізації обґрунтування щодо їх використання(ЦНТУ, 2021) Дрєєв, О. Д.; Железняк, Б. Ю.; Drieiev, O.; Zhelesnyak, B.Проектування програмного забезпечення передбачає використання кількох фреймворків, які хоч і скорочують час розробки програмного забезпечення, але мають свої можливості, недоліки та переваги. Використання фреймворка також накладає на проект певні архітектурні особливості, які залежать від обраного каркаса. Тому перед інженером-програмістом постає інтелектуальне завдання створення архітектури програмного забезпечення з вибором із ряду доступних фреймворків та з урахуванням їх впливу на функціонування системи в цілому. Результат проектування є важливим кроком, який може вплинути на успіх проекту. Тому в даній роботі розглядається проблема посилення об’єктивної складової у процесі вибору фреймворку, зокрема системи комп’ютерної візуалізації при створенні архітектури програмного забезпечення. В результаті запропоновано метод вибору системи візуалізації, який базується на аналізі завдань до системи візуалізації з виведенням вимог до побудованого зображення. Показано застосовність багатокритеріальної оптимізації для поділу застосовуваних систем візуалізації та вибору найкращої з них. Designing modern software involves the use of several frameworks. The framework reduces software development time. But frameworks have their own capabilities, disadvantages and advantages. The use of the framework also imposes certain architectural features on the project. Therefore, the engineer faces the intellectual task of creating a software architecture when you need to choose from an available set of frameworks and take into account the impact of these frameworks on the functioning of the system as a whole. The design result is an important step that has an impact on the success of the project. Therefore, this paper considers the problem of strengthening the objective component in the process of choosing a framework, namely the computer visualization system when creating a software architecture. As a result, a method for selecting a visualization system is proposed. This method is based on the analysis of tasks that are put forward in the visualization system, taking into account the requirements for the image to be built. On the basis of the formed tasks to the visualization system, the article synthesizes the requirements for the visualization systems. Also, according to experts, the importance of compliance with certain requirements is assessed. According to the characteristics of computer visualization systems and quantitative values, the evaluations provided by experts show the applicability of multicriterial optimization to separate the applicable visualization systems and choose the best one. In order to illustrate the choice of computer visualization system, the article uses an example of applying the method to a turn-based strategy game. The result is a method for selecting computer visualization systems, which is based on the created classifications of tasks facing the visualization system. The relationship between the purpose of the visualization system and the list of tasks that the visualization system must perform is shown. The paper identifies the stages that depend on subjective and objective factors. The results allow a structured approach to computer visualization systems in the software architecture design process.Item Обґрунтування конструктивної схеми пневморешітного сепаратора зерна(ЦНТУ, 2021) Васильковський, О. М.; Лещенко, С. М.; Нестеренко, О. В.; Петренко, Д. І.; Якименко, С.М.; Vasylkovskyi, O.; Leshchenko, S.; Nesterenko, O.; Petrenko, D.; Iakymenko, S.Статтю присвячено удосконаленню конструкції відцентрового пневморешітного сепаратора для розділення компонентів зернових сумішей. Базова конструкція задовільно виконує технологічний процес, однак має відносно великі вертикальні габарити за рахунок використання замкненої системи аспірації з подвійним очищенням зернової маси повітряним потоком. В роботі наведено концепцію удосконалення системи аспірації, що дозволить суттєво зменшити висоту, а також викладено методику проектного конструкторського розрахунку параметрів удосконаленої машини. The aim of the article is to improve the design of the original centrifugal grain separator. The separator is designed to separate the components of grain materials by size and aerodynamic properties. The basic design satisfactorily performs the technological process, but has large dimensions vertically. Reducing the size will simplify the design and reduce the cost of the machine. The article proposes to replace the double pneumatic cleaning of grain material with a single one. At the same time the car gets rid of the closed aspiration system. The closed aspiration system has operational advantages, however difficult adjustment reduces indicators of technological efficiency of pneumatic cleaning of grain. The original pneumatic cleaning system allows you to remove light impurities without creating significant air resistance, due to the lack of countercurrent movements. In addition, the use of an inclined pneumatic channel does not require the creation of high-speed airflow. As a result of the proposed improvement simplifies the structure and regulation of the separator, as well as reduces its size and weight. In addition to the modernization of the design of the pneumatic-sieve separator, the article presents the method of design engineering calculation of its basic geometric parameters. Depending on the specific capacity of the upper (ear) sieve and the characteristics of the grain mixture is determined by its length and angle. The remaining geometric parameters are derived from the above. Based on preliminary calculations, the following conclusions can be drawn. The use of the proposed scheme will reduce the height and weight of the centrifugal pneumatic sieve grain separator. Replacing the double air cleaning with a single one will simplify the adjustment of the machine. Experimental establishment of indicators of technological efficiency of the proposed separator will theoretically determine the dimensions and automate the design process of grain cleaning machines created by a similar scheme.