Збірники наукових праць ЦНТУ
Permanent URI for this communityhttps://dspace.kntu.kr.ua/handle/123456789/1
Browse
3 results
Search Results
Item type:Item, До розрахунку зубців прямозубих циліндричних передач на згин(ЦНТУ, 2020) Невдаха, Ю. А.; Дубовик, В. О.; Невдаха, Н. А.; Златопольський, Ф. Й.; Nevdakha, Yu.; Dubovyk, V.; Nevdakha, N.; Zlatopolskiy, F.; Дубовик, В. А.; Златопольский, Ф. И.В роботі аналізуються розрахункові схеми циліндричної прямозубої передачі на згин зубців. Розглядається найбільш поширена розрахункова схема злому зубця, де небезпечний переріз злому зуба відбувається у основі ножки вище кола діаметра западини зубців. На практиці реальний же злом зубця лежить нижче діаметра западини зубців і має опуклу форму перерізу. Для більш точного розрахунку зубців на згин досліджували коефіцієнт форми зубців. В результаті встановлено, що коефіцієнт форми зуба зменшується зі збільшенням кількості зубців. The aim of the work is to improve the calculations of spur cylindrical wheels per bend, due to the fact that the existing formulas do not give the actual value of the maximum stress, and the diagram does not correspond to the real law of stress distribution. In order to obtain satisfactory results, it is more correct to calculate the teeth at the maximum local stress. Combining the coefficients and substantiating the calculated dependence to determine the value of the coefficient of the shape of the tooth under load, applied at any point of the working profile of the tooth, to obtain formulas for the bending strength of the teeth of the gear and wheel. When calculating the bending teeth, the calculation is based on the stresses arising at the base of the tooth, under the load applied at the top of the tooth. Consider first the most common calculation scheme. Dangerous section of the tooth as seen from the plot of total stresses indicates that the maximum normal stress occurs on the non-working side of the tooth - the compression side, however, since fatigue cracks occur at the base of the tooth on the stretching side, the calculation is based on tensile stress on the working side. The hypothesis of non-curvature of flat sections is unfair for short beams of variable cross section, so the total diagram does not correspond to the real law of stress distribution. But at the base of the tooth near the transition curve is the place of stress concentration. The actual dangerous cross-section lies below the cross-section of the depression, this is confirmed by the fact that the fatigue cracks form an angle with the load curve close to straight, and the fracture of the tooth has a convex shape. In this case, it is more correct to calculate the teeth at the maximum local stress. Combining the coefficients obtained a calculated dependence to determine the value of the coefficient of the shape of the tooth under load, applied at any point of the working profile of the tooth. As a result of the study it was found that the coefficient of tooth shape decreases with increasing number of teeth. This result was expected because as the number of teeth increases, the angle between the teeth decreases, and neighboring teeth perceive part of the stress that occurs in the loaded tooth. The formulas for checking the bending strength of gear teeth and wheels are obtained. The above refinement calculations of the teeth on the bend reflect the beneficial effect of improving the accuracy of the manufacture of teeth. В работе анализируются расчетные схемы цилиндрической прямозубой передачи на изгиб зубцов. Рассматривается наиболее распространенная расчетная схема излома зубцов, где опасное сечение излома зубьев происходит в основе ножки выше круга диаметра впадины зубцов. На практике реальный же излом зубьев лежит ниже диаметра впадины зубьев и имеет выпуклую форму сечения. Для более точного расчета зубьев на изгиб исследовали коэффициент формы зубьев. В результате установлено, что коэффициент формы зуба уменьшается с увеличением количества зубьев.Item type:Item, Триботехнические исследования борсодержащих материалов нанесенных газотермическим методом для упрочнения и восстановления деталей сельскохозяйственной и автомобильной техники(КНТУ, 2010) Ивашко, В. С.; Ярошевич, В. К.; Довжук, С. А.; Златопольский, Ф. Й.; Яропуд, В. Н.; Івашко, В.; Ярошевич, В.; Довжук, С.; Златопольський, Ф.; Яропуд, В.; Ivashko, V.; Yaroshevih, V.; Dovzhuk, S.; Zlatopolskiy, F.; Yaropud, V.Проведены триботехнические исследования покрытий из сплавов переходных металлов (Fe, Co, Mn, Cr, Ni и др.), в которые для образования аморфной структуры добавляют аморфообразующие элементы типа: В, C, Si, P, S. Покрытия получали газопламенным напылением. Наиболее мелкая структура покрытия обнаружена на дистанции напыления 80 мм. Именно на этой дистанции создаются благоприятные условия для формирования аморфной фазы. Приведені результати триботехнічних досліджень покриттів із сплавів перехідних металів (Fe, Co, Mn, Cr, Ni и др.), в які для утворення аморфної структури додають аморфообразуючі елементи типу В, C, Si, P, S. Покриття отримували газополуменевим напиленням. Найбільш дрібна структура покриття виникає на дистанції напилення 80 мм. На цій дистанції створюються найбільш сприятливі умови для отримання аморфної фази. Tribological investigations of boron-containing material, coated by gas-thermal method are conducted. The goal of investigations is to control surface quality by means application of amorphous-crystalline coatings. The finest structure of coating with amorphous phase is achieved under the application distance equal to 80 mm.Item type:Item, Основные направления развития поверхностного упрочнения зубчатых колес(КНТУ, 2011) Лященко, Б. А.; Посвятенко, Э. К.; Довжук, С. А.; Златопольский, Ф. Й.; Ляшенко, Б.; Посвятенко, Е.; Довжук, С.; Златопольський, Ф.; Lyashenko, B.; Posvyatenko, E.; Dovzhuk, S.; Zlatopolskiy, F.Проанализированы тенденции развития поверхностного упрочнения зубчатых колес, преимущества и недостатки отдельных технологий, а также дана оценка наиболее перспективным решениям. Из многооперационных технологий наиболее широкое распространение для зубчатых колес получает комбинация ХТО (цементация, азотирование) и дробеструйной обработки Одна из прогрессивных технологий поверхностного упрочнения – ХТО в тлеющем разряде. Проаналізовані тенденції розвитку поверхневого зміцнення зубчастих коліс, переваги і недоліки окремих технологій, а також дана оцінка найбільш перспективним рішенням. Збагатоопераційних технологій найбільш широке поширення для зубчастих коліс отримує комбінація ХТО (цементація, азотування) і дробеструменева обробка. Одна з прогресивних технологій поверхневого зміцнення – ХТО в тліючому розряді. Progress of the superficial consolidating of gear-wheels trends, advantages and lacks of separate technologies, are analysed, and also estimation to the most perspective decisions. From technologies the most wide distribution for gear-wheels combination of cementation, nitriding and treatment One of progressive technologies of the superficial consolidating – khimiko-termicheskaya of treatment in a smouldering discharge.