Збірники наукових праць ЦНТУ
Permanent URI for this communityhttps://dspace.kntu.kr.ua/handle/123456789/1
Browse
19 results
Search Results
Item type:Item, Оцінка міцності поршневих пальців, відновлених за рахунок роздачі внутрішнього отвору(ЦНТУ, 2022) Немировський, Я. Б.; Шепеленко, І. В.; Красота, М. В.; Nemyrovskyi, Ya.; Shepelenko, I.; Krasota, M.Одним із найбільш прогресивних методів відновлення поршневих пальців ДВЗ є роздача внутрішнього отвору, що забезпечує збільшення зовнішнього діаметра зношеного пальця. У процесі подальшої обробки виконується знімання припуску із зовнішньої поверхні, що викликає витончення стінки та необхідність проведення розрахунків на міцність пальця. В роботі виконані перевірочні розрахунки міцності пальців двигунів Д245. При цьому використана схема із жорстким закріпленням вільних кінців, для чого розраховано статично невизначену балку. Виконано експериментальну перевірку аналітичних розрахунків. Проведені дослідження дозволили встановити, що використання роздачі отвору при відновленні поршневих пальців не змінює міцність та геометричні характеристики деталі. Це дозволило рекомендувати дану технологію при відновленні робочих поверхонь поршневих пальців. One of the most progressive methods of proceeding in the piston fingers of engines of internal combustion there is distribution of the internal opening that provides the increase of external diameter of threadbare finger. In the process of further treatment the output of assumption is executed from an external surface that causes reduction walls and necessity of realization of calculations on durability of finger. The aim of researches is realization of calculation on durability of piston fingers of engines of internal combustion, treat the deforming reaching. It is considered existing methodologies of estimation of durability of finger. The checking calculations of durability of fingers of motor-vehicle and tractor engines are in-process executed. Thus used chart with the hard fixing of free ends, for what an indefinite beam is expected static. The terms of fixing of finger are analysed in a piston. Verification of analytical calculations executed on the experimental setting. Realization of research allowed to set next conclusions: 1. Methodology of calculation is improved on durability of piston fingers. The use of an offer methodology allowed to execute checking calculations on durability of piston fingers of motor-vehicle and tractor engines. 2. Experimental verification of theoretical positions allowed to assert about correctness offered approach near a calculation on durability. 3. The executed analytical calculations and experimental researches showed that using of method of distribution of the internal opening for proceeding in piston fingers not substantially influenced on their durability and geometrical descriptions. It allows to recommend this technology for proceeding in this class of details.Item type:Item, Комбіновані методи обробки глибоких отворів(ЦНТУ, 2019) Свяцький, В. В.; Скрипник, О. В.; Сіса, О. Ф.; Конончук, С. В.; Свяцкий, В. В.; Скрипник, О. В.; Сиса, О. Ф.; Конончук, С. В.; Sviatskyi, V.; Skrypnyk, О.; Sisa, O.; Kononchuk, S.Наведено схеми розвантаження свердла, що основані на використанні комбінованої обробки „різання — пластична деформація” і підведенням мастильно-охолодного технічного засобу з надлишковим тиском. Способи вирішують задачі зниження складових технологічного навантаження і дозволяють розширити технологічні можливості процесу свердління по глибині обробки. Приведены схемы разгрузки сверла, основанные на использовании комбинированной обработки „резани – пластическая деформация” и подводом смазывающе-охлаждающего технического средства с избыточным давлением. Способы решают задачу снижения составляющих технологической нагрузки и позволяют расширить технологические возможности процесса сверления по глубине обработки. The drilling of deep openings is a labor-intensive technological process, especially when processing viscous materials. In the system "machine-fixture-tool-workpiece" with deep drilling in the most difficult conditions the tool – a drill. Closed processing volume, various functions, the implementation of which must provide the design of the tool, forced mode of cutting forced to work the drill body, its cutting and guiding elements with high stresses. Typically, the process of drilling deep openings is carried out on special or aggregate machines using a device containing a drill installed on a tubular stalk with ducts for chip removal and a lubricant receiving system for supplying a lubricating and cooling technical device under pressure. In the process of processing, the stem of the drill is under the influence of the axial component of the cutting force, which leads to its longitudinal bending and, consequently, to reduce the accuracy of the machining and stability of the tool. Optimization of the process of deep drilling is reduced, as a rule, to the removal of certain technical limitations on the stability, strength or stiffness of the drill. However, the possibility of increasing the stiffness of the tool due to the change in the shape of the cross section of the stem of the drill is currently sufficiently studied and practically exhausted. The above theoretical and experimental studies show that the control of the load of the tool stem along the axial component of the cutting force and the resistance forces is fundamentally possible with the use of processes of combined processing of openings. Developed methods of processing deep openings solve the problem of reducing the components of technological load and allow you to expand the technological capabilities of the drilling process at the depth of processing.Item type:Item, Експериментальне визначення жорсткості багатокоординатного верстата паралельної структури «пентапод»(ЦНТУ, 2018) Шелепко, О. В.; Кириченко, А. М.; Гречка, А. І.Роботу присвячено вимірюванню пружних переміщень робочого органа багатокоординатного верстата паралельної структури «пентапод» під навантаженням та експериментальному визначенню матриць просторової жорсткості та податливості. Розроблено схеми вимірювання переміщення робочого органа, який розташований вздовж осі Z при його навантаженні по осям Х, Y та Z. Побудовано залежності похибки переміщення робочого органа від зміни його положення відносно осі Х в діапазоні від -0,075м до 0,075 м, Y = 0, Z = 0 при постійному навантаженні рівному 100 Н вздовж осі Х, Y та Z та визначено матрицю жорсткості на основі результатів отриманих експериментальним шляхом. Работа посвящена измерению упругих перемещений рабочего органа многокоординатного станка параллельной структуры «пентапод» под нагрузкой и экспериментальному определению матриц пространственной жесткости и податливости. Разработаны схемы измерения перемещения рабочего органа, который расположен вдоль оси Z при его нагрузке по осям Х, Y и Z. Построены зависимости погрешности перемещения рабочего органа от изменения его положения относительно оси Х в диапазоне от -0,075м до 0,075 м, Y = 0, Z = 0 при постоянной нагрузке равном 100 Н вдоль оси Х, Y и Z. и определена матрица жесткости на основе результатов полученных экспериментальным путем. The article is devoted to determination of spatial stiffness of the end effector of a pentapod parallel machine tool and its relation to the end effector position into the machine workspace, determination of the compliance and stiffness matrices from experimental measurements data. To study the spatial stiffness of the machine, the method for measuring the displacements of the end effector were developed and a bench for experimental research was produced. On the basis of the results of experimental measurements, the dependence of the end effector displacement upon the change of its position relative to the X axis in the range from -0,075 m to 0,075 m with a constant load equal to 100 N along the X, Y and Z axes. The compliance and stiffness matrices of the machine is calculated on the basis of experimental measurements of the displacements Δx, Δy, Δz of the end effector by computing the nearest symmetric positive definite matrix, which is determined by the Frobenius norm. The experimental stiffness matrix 3x3 is obtained for three positions of the end effector. From the obtained dependences of the displacement of the end effector from its position relative to the X axis under constant load, the maximum displacement along the axes coincides with the direction of the load. Having obtained the compliance and stiffness matrices experimentally for different positions of the end effector, it is shown that the maximum difference in stiffness along the Y axis does not exceed 25%, and along X and Z axes is 14%. The obtained experimental results of the displacement of the end effector in machine workspace under the load force enables further establishment of the areas of the workspace in with the maximum stiffness and helps formulate guidelines to improve the pentapod machine tool spatial stiffness.Item type:Item, Методологічні аспекти використання обчислювальної техніки в курсі будівельної механіки(КНТУ, 2010) Портнов, Г. Д.; Дворніченко, А. П.В статті обговорюються проблеми, що виникають при використані комп'ютерних технологій в курсі будівельної механіки при підготовці інженерів-будівників.Item type:Item, Автоматизовані системи контролю забруднення поверхневих вод(КНТУ, 2011) Стеценко, О. С.; Глондар, К. І.Розглянути загальну характеристику якості поверхневих вод і автоматизованих засобів контролю якості води.Item type:Item, Контроль якості води річки Інгул(КНТУ, 2014) Татаров, А. В.; Стрелець, О. В.В статті представленні результати дослідження по контролю якості води р. Інгул, – яка є лівою і найбільшою притокою Південного Бугу. Контроль якості води в річці Інгул здійснювали за таким показниками: хімічне споживання кисню (ХСК) , повна біохімічна потреба кисню (БПКп), лужність, жорсткість води та вміст розчиненого кисню у воді. Згідно проведених літературних досліджень, стан води в р. Інгул можна охарактеризувати , як помірно забруднений.Item type:Item, Розробка привода для глибокого свердлення методом перехоплення стебла інструмента по його довжині(КНТУ, 2008) Пестунов, В. М.; Свяцький, В. В.; Свяцька, Л. П.Наведені теоретичні і експериментальні дослідження механізмів приводів верстатів для глибокого свердління, що мають проміжні опори. Показано, що застосування пристроїв, що використовують змінну величину вильоту інструмента в процесі обробки глибоких отворів, приводить до збільшення періоду його стійкості. In the article the theoretical and experimental research of mechanisms of machine tools drives for the deep drilling, having intermediate anvil post, are considered. The application of devices with a variable tool extension in deephole machining is bring to a tool durability are demonstrated.Item type:Item, Розвантаження свердла при комбінованій обробці глибоких отворів(КНТУ, 2008) Пестунов, В. М.; Свяцький, В. В.; Свяцька, Л. П.Наведено схему розвантаження свердла, що основана на використанні комбінованої обробки „різання – пластична деформація”. Спосіб вирішує задачу зниження складових технологічного навантаження і дозволяє розширити технологічні можливості процесу свердління по глибині обробки. The scheme of drill unloading, based on use of the combined processing „cutting – plastic deformation”, is considered. The method solves a problem of technological load components decrease and allows expanding technological capability of drilling process on depth of processing.Item type:Item, Завдання оптимізації у розв’язанні прикладних задач нелінійної механіки(КНТУ, 2012) Лисих, А. Ю.; Lisikh, А.Запропоновано метод визначення оптимальних фізико-геометричних параметрів гнучкого пружного кільцеподібного елементу, що просторово згинається, здійснює програмне обертання навколо свого діаметру. Використано прямий метод вирішення завдань оптимізації при нелінійних обмеженнях з фазовими обмеженнями-нерівностями. Для вирішення завдання використані методи диференціальної геометрії і обчислювальної математики. Чисельний алгоритм реалізований методом продовження рішення по параметру спільно з методом Ньютона-Канторовича. Отримані форми просторового обертання гнучкого кільця в результаті оптимального розподілу маси і жорсткості по довжині елементу. Результати вирішення завдання отримані у вигляді комп'ютерної графіки, алгоритм забезпечує зображення процесу в реальному режимі часу. Зроблені висновки про можливість отримання форм обертання заданої просторової конфігурації. The method of definition optimum physico-geometrical parameters of the flexible elastic spatially bent ring-shaped element, making program rotation around of the diameter is offered It is used direct method of the decision of the problems to optimization under nonlinear restrictions with phase restrictions-inequality. For decision of the problem are used methods to differential geometry and computing mathematicians. The numerical algorithm by marketed method of the continuation of the decision on parameter with method NewtonKantorovicha. Forms of the spatial rotation flexible кольца are received as a result of optimum sharing the mass and acerbity on length of the element. The results of the decision are received in the manner of computer graphs, algorithm provides the scene of the process in real mode of time. Findings are made about possibility of the reception of the forms of the rotation given spatial deskside.Item type:Item, Новий пристрій для непрямого контролю за ростом тріщин в несучих системах мобільної техніки(КНТУ, 2011) Рибак, Т. І.; Бабій, А. В.; Матвіїшин, А. Й.; Rybak, Т.; Babiy, A.; Matviyshyn, A.В роботі проведено аналіз існуючих способів контролю процесу руйнування несучих систем мобільних машин та запропоновано новий ефективний пристрій для визначення характеристик деформації рами при складному напруженому стані. Такий пристрій точно передає кут закручування між несучими елементами рами мобільної машини до чутливого елементу і не створює додаткового опору для загального процесу деформації, що дозволяє підвищити точність та надійність такого роду замірів. The analysis of existent methods of control of process of destruction of the frame systems of mobile machines is in-process conducted and a new effective device is offered for determination of descriptions of deformation of frame at the difficult tense state. The offered device exactly passes the corner of rollup between the elements of frame of mobile machine to the pickoff and does not create additional resistance for the general process of deformation, that allows to promote exactness and reliability such measurings.