Збірники наукових праць ЦНТУ
Permanent URI for this communityhttps://dspace.kntu.kr.ua/handle/123456789/1
Browse
5 results
Search Results
Item Автоматичне керування процесом індукційного наплавлення композиційних покриттів на деталі сільськогосподарської техніки(КНТУ, 2006) Аулін, В. В.; Віхрова, Л. Г.; Бісюк, В. А.; Бобрицький, В. М.Наведено аналіз етапів технологічного процесу наплавлення композиційних покриттів на деталі сільськогосподарської техніки (СГТ). Запропоновано автоматичну систему керування у вигляді структурної та функціональних схем. In this item the analysis of the stages of technological process of welding composition coverages on the details of agriculture machines. The automatic control system is offered as structural and functional diagrams.Item Вплив властивостей компонентів КМ (КП) на напружено-деформований стан і триботехнічні характеристики деталей СГТ(КНТУ, 2015) Аулін, В. В.; Кузик, О. В.; Носуленко, В. І.; Aulin, Viktor; Kuzyk, Oleksandr; Nosulenko, VictorРозглянуто різновиди контактування трибоелементів (ТЕ), зміцнених КМ (КП), які дозволяють істотно змінювати якість фізичного контакту, величину фактичної площі, здатність поверхневого шару (ПШ) ТЕ до еволюції складу і структури в процесі тертя та зношування. Виявлено ефективне гальмування руху дислокацій гетерогенними структурами КМ (КП), як при низьких, так і при високих температурах, а також рекристалізаційні процеси. Розглянуто напружений стан матеріалу ТЕ з КМ (КП) при терті. Отримано умову пластичної рівноваги компонентів у вигляді системи рівнянь та формула величини напруження при переході від матеріалу наповнювача до матеріалу матриці та визначено характер деформації, яким вони підлягають. Отримано вираз для критичного кута нахилу виступу і коефіцієнта тертя та проведена оцінка зміни коефіцієнта тертя. В процесі тертя і зношування ПШ КМ (КП) підлягає пружно-пластичному деформуванню, мало- або багато цикловому руйнуванню під силовим впливом, при протіканні теплових процесів та структурно-фазових перетворень, формуванню залишкових напружень різних знаків, спостерігається сумарний ефект силових, температурних та структурно-фазових залишкових напружень. The varieties of contact of triboelementov are considered tribo-element (TE), fortified composite material (CM) composition coating (CC), that allow substantially to change quality of physical contact, size of actual area, ability of superficial layer (SL) TE to the evolution of composition and structure in the process of friction and wear. The effective braking of motion of distributions the heterogeneous structures of CM(CC) is educed, both at subzero and at high temperatures, and also recrystallizations processes. The operating at a friction loading is distributed on hard fillers, that serve as opportune, barriers to movable distributions and reduce speed of flowage of matrix, that brings to the decline of intensity grasping over in a contact "matrix-matrix" and in a resiliently-plastic matrix there is relaxation of net voltages, minimum deformation and decline of probability of origin of cracks of tiredness. The tense state of material is considered TE of CM(CC) at a friction. The condition of plastic equilibrium of components as a system of equalizations and formula of size of tension are got in transition from material of filler to material of matrix and character of deformation is certain they are subject that. Expression for the critical angle of slope of performance and coefficient of friction and conducted estimation of change of coefficient of friction are got. In the process of friction and wear of SL CM(CC) subject to resiliently-plastic deformation, small- or much to cyclic destruction under power influence, at flowing of thermal processes and structurally-phase transformations, to forming of remaining tensions of different signs, there is a total effect of power, temperature and structurally-phase remaining tensions.Item Комп'ютерне моделювання полів температур та напружень в композиційних матеріалах та покриттях при їх формуванні, терті та зношуванні(КНТУ, 2014) Аулін, В. В.; Бобрицький, В. М.; Aulin, Viktor; Bobrytskyi, VitaliiВ статті за допомогою комп’ютерного моделювання досліджено поле температур та напружено- деформований стан композиційних матеріалів та покриттів на всіх етапах їх життєвого циклу. Визначено розподіл нестаціонарних полів температур та напружень, які виникають в композиційних матеріалах та покриттях в процесі їх формування і тертя та зношування, а також локальні області з максимальною різницею перепаду температур і напружень та вплив на них внутрішніх і зовнішніх факторів. Виявлено тісний взаємозв'язок між складом композиційних матеріалів і покриттів, розмірами і формою їх структурних складових та статистичними і локальними значеннями досліджуваних полів температур і напружень відповідних нестаціонарних полів. Результати комп’ютерного моделювання дають можливість оптимізувати склад та структуру композиційних матеріалів та покриттів для підвищення їх фізико-механічних та триботехнічних характеристик і властивостей. The article by computer simulation investigated the distribution of temperature and stress-strain state of composite materials and coatings at all stages of their life cycle. Determined the distribution of transient temperature fields, stresses and strains that occur in composite materials and coatings in the process of forming and friction and wear , as well as local areas with a maximum difference of temperature and stress and the impact on their internal and external factors. Computer simulation of composite materials and composite coatings made it possible to construct a non-stationary heat field and thermal stress field in composite materials and composite coatings with dispersion - strengthened and eutectic types of structures that arise from stationary sources of heat ( of friction ). It is shown that the configuration of these fields are essentially uniform, there are significant changes in temperature and stress due to heterogeneity of structure heterogeneity thermophysical and mechanical properties of the structural components of composite materials and composite coatings that achieve , depending on the load of friction , melting components, and local stress - up to several GPa. The value of tensile stress and compressive alternating throughout the volume of the composite material and composite coatings. There is a close relationship between the structure of composite materials and composite coatings, the size and shape of structural components and statistical and local values of temperature and stress appropriate nonstationary fields. To minimize temperature changes and thermal stresses to use uniform size structure of the filler with a maximum dispersion of carbides and align the thermal properties of filler and matrix, which must provide high relaxation ability. According to the results of computer simulation can optimize the composition and structure of composite materials and coatings to enhance their physical and mechanical characteristics and tribotechnical.Item Перспективи розвитку автоматичного управління технологічним процесом наплавлення композиційних покриттів(КНТУ, 2008) Віхрова, Л. Г.; Аулін, В. В.; Бісюк, В. А.; Гамалій, В. Ф.Представлено результати аналізу способів автоматичного управління режимом наплавлення композиційних покриттів, запропоновано спосіб автоматизації керування температурою індукційного наплавлення композиційного покриття та спосіб управління складом композиційного матеріалу, наведено їх функціональні схеми, описано принцип роботи. The results of analysis of methods of automatic control of smelting of composition coverages the mode are presented, the method of automation of control of induction smelting of composition coverage a temperature and method of management of composition material composition is offered, they are resulted functional diagrams, and their principle of work is described.Item Автоматичне управління температурою та тривалістю індукційного нагрівання при наплавленні композиційних покриттів на деталі машин(КНТУ, 2009) Віхрова, Л. Г.; Аулін, В. В.; Бісюк, В. А.Наведено результати аналізу факторів, що впливають на якість індукційного наплавлення композиційних покриттів, запропоновано методи управління параметрами процесу індукційного наплавлення, наведено рівняння, що визначають залежність температури наплавлення від параметрів процесу. The results of analysis of factors which influence on quality induction smelting of composition coverages are resulted, the methods of management the parameters of process of induction smelting are offered, equalizations which determine dependence of temperature of smelting from the parameters of process are resulted.