Збірники наукових праць ЦНТУ
Permanent URI for this communityhttps://dspace.kntu.kr.ua/handle/123456789/1
Browse
6 results
Search Results
Item Вплив рослинних решток на інтенсивність абразивного зношування робочих органів ґрунтообробних машин(ЦНТУ, 2020) Борак, К. В.; Borak, K.Абразивний знос один з найпоширеніших видів зношування, на його долю припадає до 50% всіх відмов деталей машин. Дослідження закономірностей процесу абразивного зношування є безумовно актуальною задачею. В роботі розглянуто вплив хімічного фактору, а саме наявність рослинних решток в абразивній масі, на інтенсивність зношування робочих органів ґрунтообробних машин. Лабораторні дослідження проводили за методом «крильчатки», а експлуатаційні – на універсальному дисковому агрегаті УДА 4,5 в умовах Овруцького району Житомирської області (ґрунти супіщані). В результаті проведення досліджень з’ясовано, що при виділені соків (патоки) підвищується інтенсивність абразивного зношування в лабораторних умовах на 13,5…21,5%, а в експлуатаційних умовах – на 8%. Абразивне зношування робочих органів ґрунтообробних машин є доволі складним процесом і не може розглядатися тільки механічної точки зору. Abrasive wear is one of the most common types of wear accounting for up to 50% of all failures of machine parts. The study of laws governing the process of abrasive wear process is undoubtedly a critical task. The paper is dedicated to the effect that the chemical factor, in particular the presence of plant remains in the abrasive mass, has on the tilling machine movable operating parts abrasive wear rate. Laboratory researches were performed with the Impeller technique, while the field tests – with a multipurpose disk tiller UDA-4.5 in the conditions of the Ovruch district of Zhytomyr region (sandy loam soil). As follows from the study, the ooze of the sap (syrup) leads to an increase of the abrasive wear rate by 13,5…21,5% in the laboratory conditions. As a result, it was found that the rate of mass wear of the disk working bodies (multipurpose disk tiller UDA-4.5) on the field after corn was increased by 8% compared to the rate of wear of the disk working bodies on the field without plant residues. Results of the field tests confirm those of the laboratory studies, although the latter have demonstrated an increase in the wear rate, which is by 13,5% greater than got upon the field tests. Such a deviation is conditioned by a higher concentration of the corn crop remains in the abrasive mass during laboratory testing. Abrasive wear of the tilling machine movable operating parts may not be identified as a simple mechanical process, as the working surface wear rate may be significantly increased by the chemical factor when subject to wear in the real soil. Абразивный износ один из самых распространенных видов износа, на его долю приходится до 50% всех отказов деталей машин. Исследование закономерностей процесса абразивного износа является, актуальной задачей. В работе рассмотрено влияние химического фактора, а именно наличие растительных остатков в абразивной массе, на интенсивность износа рабочих органов почвообрабатывающих машин. Лабораторные исследования проводили по методу «крыльчатки», а эксплуатационные – на универсальном дисковом агрегате УДА 4,5 в условиях Овруцкого района Житомирской области (почвы супесчаные). В результате проведения исследований установлено, что при выделении соков (патоки) повышается интенсивность абразивного износа в лабораторных условиях на 13,5...21,5%, а в эксплуатационных условиях – на 8%. Абразивный износ рабочих органов почвообрабатывающих машин это очень сложный процесс и не может рассматриваться только механической точки зрения.Item Дослідження зносостійкості сталі 65Г з різними фізико-механічними властивостями при зношуванні в абразивній масі(КНТУ, 2016) Дворук, В. І.; Борак, К. В.; Добранський, С. С.; Dvoruk, V.; Borak, К.; Dobranskyi, S.Досліджено вплив природи, твердості абразивного матеріалу та тиску абразивної маси на зносостійкість сталі 65Г з різними фізико-механічними властивостями при зношуванні в абразивній масі, що імітує ґрунт. The purpose of research – to investigate the influence of nature and abrasive hardness and pressure abrasive wear resistance to steel weight 65Г with different physical and mechanical properties in wear in abrasive mass. The work for predicting the durability of the tillage work reinforced by electrical discharge machining, studies were conducted relative and absolute wearing ability of soils with different fractional composition, and to take account of the impact speed and pressure of the soil surface was made two-factor experiment. The criterion of optimization in the studies were offered: σW - durability km/h. As a result of the research might draw the following conclusions: - increased durability samples at reduced speed, due to the increase of dynamic loads on the surface friction. - surface wear resistance is significantly reduced with increasing pressure on the specific sample is explained by the fact that the increase in pressure may cause such negative processes as mikrorizannya metal surface with abrasive grains. - 65 G enhanced wear resistance of steel during quenching and tempering average of 15 ... 30%, the electrical treatment to 60..80% despite external factors (pressure and speed).Item Методика експлуатаційних досліджень зношування робочих органів дискових ґрунтообробних знарядь(КНТУ, 2009) Герук, С. М.; Борак, К. В.; Geruk, S.; Borak, K.Наведена методика експлуатаційних досліджень зношування робочих органів дискових грунтообробних знарядь. Розроблена методика дозволяє досліджувати закономірності та характер процесу зношування, динаміку зношування, вплив експлуатаційних факторів на зносостійкість та ресурс дискових робочих органів. The method of operating researches of wear of workings organs of disk soil instruments is resulted. The developed method allows to probe conformities to the law and character of process of wear, dynamics of wear, influence of experimental factors on wearproofness and resource of disk workings organs.Item Самозагострювання робочих органів ґрунтообробних знарядь(КНТУ, 2015) Дворук, В. І.; Войтов, В. А.; Борак, К. В.; Dvoryk, Volodymyr; Voytov, Viktor; Borak, KonstantinДосліджено вплив фізико-механічних властивостей матеріалу робочого органу, абразивних властивостей ґрунтів і конструктивних параметрів робочого органу на виникнення ефекту самозагострення. Отримані уточненні умови самозагострювання для робочих органів дискових ґрунтообробних знарядь. Set conditions of independent intensifying working organ soil-cultivating instruments. Influence of mechanical properties of material working organ, abrasive properties soils, structural parameters of working organ is investigational on the origin effect of independent intensifying. Got clarification of condition of independent intensifying for the workings organs of disk soil-cultivating instruments: 1. Value thickness and hardness of the strengthening and base layer should be a lifetime condition to ensure R < Rɞ. 2. The thickness of the base layer should be as short as possible, while providing the necessary increase in strength solid layer. 3. The hardness of hardened layer should be determined in relation to the base layer hardness depending on the abrasive properties of soil. 4. Strengthening and exacerbate the line and must be subject to more intense wear that. 6. Sharpening angle must be at 28Û ... 30Û. To achieve the effect independent intensifying working organ soil-cultivating instruments must fulfill five conditions and the second and the third condition suggested by V.M. Tkachev for plowshares completely fair and intensifying working organ soil-cultivating instruments, the first condition is clarified, and 4 opposite condition is reversed.Item Дослідження зношування робочих органів дискових борін(КНТУ, 2008) Герук, С. М.; Борак, К. В.; Нечипоренко, В. О.Наведено результати досліджень зношування робочих органів дискових борін та встановлено особливості характеру їх спрацювання для вітчизняних і зарубіжних машин. It is presented results of researches of wear process of working organs of disk harrows and it is established features of character of their deterioration for domestic and foreign machines.Item Вплив електроерозійної обробки на хімічний склад та структуру сталі 65Г(КНТУ, 2011) Борак, К. В.; Borak, K.Приведені результати лабораторних досліджень впливу електроерозійної обробки на хімічний склад та структуру сталі 65Г. З’ясовано, що результаті електроерозійної обробки сталі 65Г утворюється поверхневий шар з дрібногольчастою мартенситною структурою. Також поверхневий шар насичується хромом, нікелем, кремнієм та марганцем. В результаті досліджень запропоновано раціональний режим електроерозійної обробки. The resulted results of laboratory researches of influence of electricalerosion treatments are on chemical composition and structure of steel of 65Г. It is found out, that result of electricalerosion threatening of steel of 65Г a superficial layer appears from finely needle by a martensitnoy structure. Also a superficial layer is saturated a chrome, nickel, silicon and manganese. As a result of researches the offered rational mode of electricalerosion treatments.