Збірники наукових праць ЦНТУ
Permanent URI for this communityhttps://dspace.kntu.kr.ua/handle/123456789/1
Browse
5 results
Search Results
Item Експериментальне дослідження залежності стійкості інструменту від інтенсивності охолодження і режимів різання(ЦНТУ, 2019) Лисих, А. Ю.; Будуров, В. Л.; Лысых, А. Ю.; Lisikh, A.; Bydyrov, V.У статті представлено експериментальне дослідження залежності стійкості інструмента від кількості мастильно-охолоджувальної рідини і витрат потужності при свердлінні свердлами зі змінними багатогранними пластинами, що дозволить збільшити період стійкості і зменшити витрати потужності при використанні багатогранних змінних пластин. В статье представлено экспериментальное исследование зависимости периода стойкости от расхода смазочно-охлаждающей жидкости и затрачиваемой мощности при сверлении свердлами с сменными многогранними пластинами, что позволит увеличить период стойкости и уменьшить затрачиваемою мощность при использовании многогранных сменных пластин. В статье представлено экспериментальное исследование зависимости периода стойкости от расхода смазочно-охлаждающей жидкости и затрачиваемой мощности при сверлении свердлами с сменными многогранними пластинами, что позволит увеличить период стойкости и уменьшить затрачиваемою мощность при использовании многогранных сменных пластин. It is presented in article experimental researches of the period of stability of variable many-sided plates of the cutting tool and power when drilling from intensity of cooling in a cutting zone. Such analysis is necessary for improvement of metal working of new structural materials and is of scientific and practical interest. The purpose of work is experimental researches on necessary amount of cooling liquid for ensuring the maximum stability of the tool that will allow to reduce expenses on the tool and will reduce prime cost of the manufactured products. The research concerning determination of necessary amount of cooling liquid for ensuring the maximum stability of the tool and also reduction power expenses is conducted. The experiment was conducted on the machine the processed center SPACE TURN LB 3000EX of Oruma to which the hydrometer in the system of supply of cooling liquid and a stop watch for fixation of time of measurement was built in. As the cutting tool it was used drills with replaceable plates of the following diameters of Ø20, Ø24, Ø28 of SEKO. As cooling liquid Akvol cooling liquid which similar to foreign brands was used. It is carried out to 10 single measurements of a consumption of cooling liquid and the period of stability and also capacities behind each of the modes it is sharp and calculation of average value is carried out. Results of a research are given in a type of graphic dependences that is confirmed by work conclusions. The analysis of the received results is made. Experimental researches are conducted showed that thanks to supply lubricant cooling liquid in a zone of cutting the coefficient of friction decreases and temperature in a cutting zone at the expense of what decreases the stability period to the tool increases. It is also established that at increase in giving of the tool and speed of cutting the period of stability decreases and increases power expenses. Practical application of these experimental researches will allow to reduce expenses on the tool and to reduce prime cost of the manufactured products.Item Теплообмін і тертя турбулентного потоку газу в трубі при малих числах Рейнольдса(ЦНТУ, 2017) Святецький, М. В.; Ошовський, В. Я.; Капура, І. А.; Будуров, В. Л.; Svyatetsky, M.; Oshovsky, V.; Kapura, I.; Budurov, V.В статті проаналізовані відомі результати експериментальних і теоретичних досліджень розглядуваних процесів. Загальним недоліком згадуваних робіт є відсутність належної фізичної обгрунтованості прийнятих напівемпіричних теорій, що не дозволяє достатньо коректно врахувати специфіку процесів турбулентного переносу і істотно обмежує область застосування одержаних результатів. Показано, що врахування взаємодії молекулярного і молярного механізмів переносу, які кількісно порівнянні, дає можливість узгодити експериментальні результати з теоретичними. Таким чином викладений метод дозволяє з єдиних позицій розраховувати характеристики теплообміну і гідродинаміки газового потоку в трубі в широкому діапазоні чисел Рейнольдса. The purpose of the paper is to study the features of turbulent heat and momentum transfer in round tubes at small Reynolds numbers. The article analyzes the results of experimental and theoretical studies of the processes under consideration. The general disadvantage of the above-mentioned works is the lack of proper physical validity of the accepted semi-empirical theories, which does not allow us to properly take into account the specifics of the processes of turbulent transfer and substantially limits the scope of the applicability of the results obtained. It is shown that the account of the interaction of the molecular and molar transport mechanisms which are quantitatively comparable gives the possibility to reconcile the experimental results with the theoretical. The thus expounded method allows from single positions to expect descriptions of heat exchange and hydrodynamics of gas stream in a pipe in the wide range of numbers of Reynolds.Item Модернізація спеціальної оправки з торцевою фрезою-протяжкою, яка працює за схемою прогресивного фрезерування(ЦНТУ, 2017) Анастасенко, С. М.; Григурко, І. О.; Будуров, В. Л.; Anastasenko, S.; Grigyrkо, І.; Bydyrov, V.У статті представлена модернізація конструкції спеціальної оправки для торцевої фрези зі зміщеним центром обертання. Розроблено схему прогресивного фрезерування поверхонь за допомогою спеціальної оправки для фрези-протяжки, яка забезпечує знімання припуску від 10 до 30 мм за один прохід. The article presents the design upgrading of a special mandrel for a face milling cutter with a displaced center of rotation in order to decrease labor intensity when milling surfaces with large allowances, to reduce the production cost and to increase the cutting power of inserts of the broach milling cutter. An upgraded design of a special mandrel with a displaced center of rotation for the broach milling cutter has been proposed. The design upgrading of the special mandrel with a displaced center of rotation of the cutter for the face broach milling cutter allows to multiply the cutting power of inserts of the broach milling cutter by about 3 times and reduce the labor intensity of manufacturing per part by 4-5 times, which significantly affects the reduction of the unit cost production. A scheme of advanced milling of surfaces with the help of a special mandrel for the broach milling cutter, which ensures the removal of the allowance from 10 to 30 mm in one pass, has been devised.Item Вплив режимів різання на збереження стійкості інструмента : проблеми та шляхи їх вирішення(КНТУ, 2016) Анастасенко, С. М.; Будуров, В. Л.; Григурко, І. О.; Anastasenko, S.; Bydyrov, V.; Grigyrkо, І.У статті визначено вплив чинників на стійкість інструмента. Досліджено наступні чинники: швидкість різання, подача, глибина різання, задній кут, головний кут в плані, допоміжний кут в плані, радіус при вершині, передній кут, змінні багатогранні пластини (ЗБП). Встановлено і систематизовано причини зниження стійкості інструмента та запропоновано шляхи збереження стійкості інструмента. Research of the influence of cutting speed, feeding, cutting depth, end-clearance angle, plan approach angle, minor cutting edge angle, tip radius and the face angle on the tool durability. Materials that are used for manufacturing of cutting tools are expensive. Therefore the cost of cutting tools is rather high, as well as the production cost of goods produced by means of such tools. Thus one has to decide how to reduce manufacturing costs. There are two ways to solve the problem. The first way is to create some new materials to make the cutting tools more resistant than the existing ones, and the second way is to optimize cutting conditions to ensure maximum performance while maintaining the tool durability. The first way is quite long and the cost of the new tools will be not lower than the existing one. The second way is more realistic. The study identified and systematized the factors that affect the tool durability. The study allows to conclude that all cutting parameters in one way or another affect the tool durability and production costs. Therefore the need for compliance of the cutting parameters is crucial for ensuring the stability of the cutting tool, and as much for the competitiveness of products.Item Модернізація вузлів обладнання для механічної обробки гільзи циліндрів двигуна на токарних верстатах застарілої конструкці(КНТУ, 2015) Анастасенко, С. М.; Григурко, І. О.; Ошовський, В. Я.; Будуров, В. Л.; Anastasenko, Sergey; Grigyrko, Ivan; Ohsovsrsy, Victor; Bydyrov, VasilyУ статті представлена модернізація токарних верстатів застарілої конструкції з реконструкцією гідрокопіювальних супортів для механічної обробки гільзи циліндра двигуна та улаштування для автоматизованого завантаження, закріплення і зняття заготовок. При конструкторській розробці на заводі можливо враховувати виробничі можливості ремонтних і інструментальних цехів, на котрі покладається задача переобладнання верстатів і ретельного розрахунку економічних показників,які визначають рентабельність реконструкції і степені автоматизації. В більшості випадків при автоматизації верстатів для роботи за замкнутим циклом виготовлення простих деталей можемо рекомендувати пневмомеханічні улаштування, комбінуючи механічний барабанний привід супорту з пневматичними затискними улаштуваннями. In article modernization of lathes of an outdated design with reconstruction of hydrocopy calipers is provided for machining of a cylinder liner of the engine and the device for the automated loading, fastening and removal of preparations. At design development at plant it is possible to consider production capabilities of maintenance and tool shops to which the problem of re-equipment of machines and careful calculation of economic indicators which define profitability of reconstruction and extent of automation is assigned. In many cases at automation of machines for work behind the closed cycle production of simple details is recommended the pneumomechanical devices combining a mechanical drum drive gear of a caliper with air clamping devices. Re-equipment of the machine is reduced to installation of tightening cylinders, to production of mandrels and the rotating spindle of the rear grandma. Cylinders and cranes of steering and shops. Lathe productivity with a hydrocopy caliper and loading organization will increase by 10 times equalizing it with a productivity at manual service, and expenses will pay off approximately in three months.