Збірники наукових праць ЦНТУ
Permanent URI for this communityhttps://dspace.kntu.kr.ua/handle/123456789/1
Browse
6 results
Search Results
Item Попередні дослідження пасивного струнного решета(ЦНТУ, 2022) Васильковський, О. М.; Лещенко, С. М.; Петренко, Д. І.; Мороз, С. М.; Нестеренко, О. В.; Vasylkovskyi, O.; Leshchenko, S.; Petrenko, D.; Moroz, S.; Nesterenko, О.У статті викладені результати досліджень роботи моделі оригінального струнного решета. На основі аналізу наукових праць сформульовано гіпотезу щодо підвищення ефективності сепарації зерна і зниження енергетичних витрат шляхом використання струнних пасивних решіт з шнурів Dyneema. Попередні дослідження моделі підсівного решета були проведені шляхом реалізації плану повного факторного експерименту. Встановлено працездатність і виявлені основні показники роботи оригінального решета. Виявлені недоліки конструкції і сформульовані завдання для подальших досліджень. The article presents the results of research into the operation of the model of the original string sieve. The sieve is equipped with synthetic strings made of ultra-small diameter Dyneema braided cord. The purpose of this study is to evaluate the performance and identify the main indicators of the technological efficiency of the proposed fixed sieve installed at an angle to the horizon. Preliminary studies of the sowing sieve model were carried out by implementing the plan of a full factorial experiment. The experiments were carried out on a model of a seed sieve with holes of 2 mm. In the course of experiments, a post-harvest heap of winter wheat with natural clogging was used. The criterion for evaluating the efficiency of separation is the mass of seeding, and the specific feed and the angle of inclination of the sieve are the operating factors. The operational efficiency was established and the main performance indicators of the model were identified. The statistical mathematical model of the process allows us to assert the linear dependence of the criterion on the operating factors and to obtain a quantitative assessment of their influence on the process of cleaning the grain mixture. The surface of the response of the mass of the selected seeding from the specific loading of a unit of the sieve area and the angle of its inclination is constructed. An analysis of the regression equation and the response surface was carried out, during which design flaws were identified and tasks for further research were formulated. The factor that was found to be influential in the course of the previous experiments – the angle of inclination at the minimum value does not fully ensure guaranteed performance, since during the experiments clogging and accumulation of piles on the separating surface were periodically observed. An increase in the mass of the selected seeding is achieved by reducing the angle of the passive sieve to 17º and increasing the specific supply to 160 kg/dm2 ◌ּh. A decrease in feed worsens the sieving process, especially at a small angle of inclination of the sieve, however, according to the Student's test, it is not significant. The resulting non-classical dependence may indicate the imperfection of the layout, the influence of unforeseen factors, etc., and requires further research.Item Обґрунтування конструктивної схеми пневморешітного сепаратора зерна(ЦНТУ, 2021) Васильковський, О. М.; Лещенко, С. М.; Нестеренко, О. В.; Петренко, Д. І.; Якименко, С.М.; Vasylkovskyi, O.; Leshchenko, S.; Nesterenko, O.; Petrenko, D.; Iakymenko, S.Статтю присвячено удосконаленню конструкції відцентрового пневморешітного сепаратора для розділення компонентів зернових сумішей. Базова конструкція задовільно виконує технологічний процес, однак має відносно великі вертикальні габарити за рахунок використання замкненої системи аспірації з подвійним очищенням зернової маси повітряним потоком. В роботі наведено концепцію удосконалення системи аспірації, що дозволить суттєво зменшити висоту, а також викладено методику проектного конструкторського розрахунку параметрів удосконаленої машини. The aim of the article is to improve the design of the original centrifugal grain separator. The separator is designed to separate the components of grain materials by size and aerodynamic properties. The basic design satisfactorily performs the technological process, but has large dimensions vertically. Reducing the size will simplify the design and reduce the cost of the machine. The article proposes to replace the double pneumatic cleaning of grain material with a single one. At the same time the car gets rid of the closed aspiration system. The closed aspiration system has operational advantages, however difficult adjustment reduces indicators of technological efficiency of pneumatic cleaning of grain. The original pneumatic cleaning system allows you to remove light impurities without creating significant air resistance, due to the lack of countercurrent movements. In addition, the use of an inclined pneumatic channel does not require the creation of high-speed airflow. As a result of the proposed improvement simplifies the structure and regulation of the separator, as well as reduces its size and weight. In addition to the modernization of the design of the pneumatic-sieve separator, the article presents the method of design engineering calculation of its basic geometric parameters. Depending on the specific capacity of the upper (ear) sieve and the characteristics of the grain mixture is determined by its length and angle. The remaining geometric parameters are derived from the above. Based on preliminary calculations, the following conclusions can be drawn. The use of the proposed scheme will reduce the height and weight of the centrifugal pneumatic sieve grain separator. Replacing the double air cleaning with a single one will simplify the adjustment of the machine. Experimental establishment of indicators of technological efficiency of the proposed separator will theoretically determine the dimensions and automate the design process of grain cleaning machines created by a similar scheme.Item До створення концепції «ідеального» решета зернового сепаратора(ЦНТУ, 2020) Васильковський, О. М.; Лещенко, С. М.; Мороз, С. М.; Нестеренко, О. В.; Молокост, Л. А.; Vasylkovskyi, O.; Leshchenko, S.; Moroz, S.; Nesterenko, O.; Molokost, L.; Васильковский, А. М.; Лещенко, С. Н.; Мороз, С. Н.; Нестеренко, А. В.У статті викладені міркування щодо створення умов для інтенсифікації процесу сепарації зерна за геометричними ознаками. Проведено огляд конструкцій і аналіз роботи відомих решітних поверхонь з позиції можливості забезпечення високих показників технологічної ефективності за рахунок прискорення орієнтації часток відносно отворів решета. Встановлено, що найбільш сприятливі умови орієнтації забезпечують поверхні, утворені повздовжніми елементами малого перерізу обтічної форми, що мінімізують можливість розташування на них часток в положеннях стійкої рівноваги. Виявлено теоретичні можливості збільшення площ живого перерізу та коефіцієнтів живого перерізу решітних полотен, що не мають поперечних перетинок. Наведені залежності сумарної ширини повздовжніх перетинок і коефіцієнта живого перерізу решіт від ширини повздовжніх перетинок для різних решіт. Це дає можливість візуальної оцінки необхідності збільшення живого перерізу решіт шляхом зменшення ширини повздовжніх перетинок, які їх утворюють. Суттєве зменшення ширини перетинок стає можливим завдяки використання нових матеріалів – плетених шнурів з надвисокомолекулярних поліетиленів типу Spectra/Dyneema, що забезпечують високі показники механічної міцності і зносостійкості при «абсолютній» нерозтяжності. The article presents considerations for creating conditions for the intensification of the process of grain separation by geometric features. The review of constructions and the analysis of work of known sieve surfaces from a position of possibility of maintenance of high indicators of technological efficiency at the expense of acceleration of orientation of particles concerning sieve apertures is carried out. It is established that the most favorable orientation conditions are provided by the surfaces formed by longitudinal elements of small cross-section of streamlined shape, which minimize the possibility of placing particles on them in positions of stable equilibrium. Theoretical possibilities of increasing the living cross-sectional areas and live cross-sectional coefficients of sieve canvases without cross-sections are revealed. The dependences of the total width of the longitudinal sections and the coefficient of the living cross section of the sieves on the width of the longitudinal sections for different sieves are given. This makes it possible to visually assess the need to increase the living cross section of the sieves by reducing the width of the longitudinal sections that form them. A significant reduction in the width of the partitions is possible due to the use of new materials - braided cords made of ultra-high molecular weight polyethylene type Spectra / Dyneema, which provide high mechanical strength and wear resistance with «absolute» inextensibility. В статье изложены соображения по созданию условий для интенсификации процесса сепарации зерна по геометрическим признакам. Проведен обзор конструкций и анализ работы известных решетных поверхностей с позиции возможности обеспечения высоких показателей технологической эффективности за счет ускорения ориентации частиц относительно отверстий решета. Установлено, что наиболее благоприятные условия ориентации обеспечивают поверхности, образованные продольными элементами малого сечения обтекаемой формы, которые минимизируют возможность расположения на них частиц в положениях устойчивого равновесия. Выявлены теоретические возможности увеличения площади живого сечения и коэффициента живого сечения решетных полотен, которые не имеют поперечных перегородок. Приведены зависимости суммарной ширины продольных перегородок и коэффициента живого сечения решет от ширины продольных перегородок для различных решет. Это дает возможность визуальной оценки необходимости увеличения живого сечения решет путем уменьшения ширины продольных перегородок, которые они образуют. Существенное уменьшение ширины перепонок становится возможным благодаря использованию новых материалов - плетеных шнуров их сверхвысокомолекулярных полиэтиленов типа Spectra/Dyneema, обеспечивающих высокие показатели механической прочности и износостойкости при «абсолютной» неростяжимости.Item Експериментальні дослідження енергоємності роботи відцентрового прямоточного сепаратора зерна(ЦНТУ, 2019) Васильковський, О. М.; Лещенко, С. М.; Мороз, С. М.; Петренко, Д. І.; Васильковский, А. М.; Лещенко, С. Н.; Мороз, С. Н.; Петренко, Д. И.; Vasylkovskyi, O.; Leshchenko, S.; Moroz, S.; Petrenko, D.У статті наведено результати експериментальних досліджень енергоємності роботи оригінального відцентрового прямоточного повітряно-решітного очисника зернового вороху, в основу якого покладено багатофункціональний робочий орган – лопатевий ротор. У попередніх дослідженнях нами встановлені основні закономірності зміни енергетики даного сепаратора при роботі в режимі холостого ходу. Проведена нова серія експериментальних досліджень дозволила отримати залежності повної потужності на привід лопатевого ротора та потужності, що витрачається на розгін і переміщення зерна по решету від основних конструктивних та технологічних параметрів відцентрового прямоточного сепаратора зерна. В статье приведены результаты экспериментальных исследований энергоемкости работы оригинального центробежного прямоточного воздушно-решетного очистителя зернового вороха, в основу которого положен многофункциональный рабочий орган - лопастной ротор. В предыдущих исследованиях нами установлены основные закономерности изменения энергетики данного сепаратора при работе в режиме холостого хода. Проведенная новая серия экспериментальных исследований позволила получить зависимости полной мощности на привод лопастного ротора и мощности, расходуемой на разгон и перемещения зерна по решету от основных конструктивных и технологических параметров центробежного прямоточного сепаратора зерна. The purpose of the work is an experimental study of the components of the power on the drive of the original centrifugal pneumatic grate grain separator, as well as to determine the dependence of power on the basic design parameters of the impeller rotor and machine performance. Obtaining these regularities allows the design of centrifugal direct-flow grain-cleaning machines of different performance and to predict their energy performance in advance. The experiments were performed on a grain mixture of wheat with a moisture content of 13.6%. Contamination with small impurities was 5%. The main studies were performed on a laboratory stand that completely reproduces the experimental separator. The basis of the separator is the original arcuate sieve sieve and the blade rotor - grain accelerator. The number of rotor blades was 24. Determination of power per drive was carried out using the device K-50. During the experiments, two factors were changed - productivity (flow) and the kinematic index, which is a complex indicator and takes into account the radius and angular velocity of the rotor blade. As a result of the experiment, the dependences of the full power consumption for the drive of the blade rotor on the feed were obtained for different values of the kinematic mode index. Taking into account the previous experiments on determining the idling power, we determined the dependence of the power costs for the movement of grain on the arcuate sieve of a centrifugal flow separator from the feed for different values of the kinematic mode index. The total power on the drive of the rotor blade is proportional to the feed and is in the range of 100… 194 watts at kinematic indexes 113… 314 at feeds of 0.2… 1.25 kg / s. The power consumed to move the grain along the sieve is 10… 78 watts. In this case, there is a decrease in power gain with a proportional increase in flow, which can be explained by the movement of particles between layers. Additional tests are required to test the hypothesis of the relative movement of particles between layers.Item Дослідження енергоємності холостого ходу відцентрового сепаратора зерна(ЦНТУ, 2018) Васильковський, О. М.; Лещенко, С. М.; Мороз, С. М.; Петренко, Д. І.; Васильковский, А. М.; Лещенко, С. Н.; Мороз, С. Н.; Петренко, Д. И.; Vasylkovskyi, O.; Leshchenko, S.; Moroz, S.; Petrenko, D.У статті описано результати досліджень показників енергоємності роботи оригінального інерційного прямоточного сепаратора зерна оснащеного лопатевим ротором. Теоретичний аналіз дозволив встановити, що однією зі складових потужності холостого ходу є коефіцієнт пропорційності, який враховує енергетику внутрішніх процесів. Проведені експериментальні дослідження дозволили отримати залежності приводної потужності та коефіцієнту пропорційності від параметрів лопатевого ротора відцентрового прямоточного сепаратора зерна в режимі холостого ходу. В статье описаны результаты исследований показателей энергоемкости работы оригинального инерционного прямоточного сепаратора зерна оснащенного лопастным ротором. Теоретический анализ позволил установить, что одной из составляющих мощности холостого хода является коэффициент пропорциональности, учитывающий энергетику внутренних процессов. Проведенные экспериментальные исследования позволили получить зависимости приводной мощности и коэффициента пропорциональности от параметров лопастного ротора центробежного прямоточного сепаратора зерна в режиме холостого хода. The article describes the results of studies on the energy intensity of the work of the original inertial direct-flow grain separator equipped with a spindle rotor. An important part of the work of grain cleaning machines is the energy performance. They affect the cost of the final product. The energy of classical separators is sufficiently studied, but the creation of fundamentally new structures requires research. Therefore, the establishment of the power of the drive of the working bodies is an urgent task. The construction of an original centrifugal direct-flow grain separator was created at the Department of Agricultural Engineering of the Kirovohrad National Technical University. The machine allows air and grinding of grain to be cleaned. It is based on an original blade rotor, which performs several functions - air flow, acceleration of grain, cleaning of sieve openings and unloading of a clean product. An important characteristic of the separator is the idle speed. The theoretical analysis allowed to establish that one of its components is the coefficient of proportionality, which takes into account the energy of internal processes. Solving the problem was carried out on a laboratory experimental installation. The conducted empirical studies allowed to obtain the dependence of the drive power and the coefficient of proportionality on the parameters of the shaft rotor of the centrifugal direct-flow grain separator in idle mode. In particular, the following is established. The idle speed of the centrifugal grain separator increases parabolic with an increase in the angular velocity of the blade rotor, while the number of blades does not affect the power. The coefficient of proportionality, characterizing power in idle mode, decreases with increasing angular rotor speed. Increasing the number of blades also reduces the value of the proportionality factor. The obtained results will allow to calculate the parameters of centrifugal direct-current separators at the design stage and to evaluate the energy of already created machines. Determining other components of energy intensity requires further research.Item Технічні засоби для одночасного завантаження та розділення зернового вороху за розмірами(КНТУ, 2014) Мороз, С. М.; Васильковський, О. М.; Анісімов, О. В.; Moroz, Sergey; Vasylkovskii, Aleksey; Anisimov, AleksandrВ статті проведено аналіз конструкцій робочих органів сільськогосподарських машин для одночасного транспортування та решітного очищення зернового вороху від крупних домішок. Проведений аналіз дозволив встановити їх основні переваги та недоліки і запропонувати оригінальну конструкцію нового транспортера-сепаратора зерна. The aim of the article is to determine the most efficient working body for loading and separation of the grain size at the same time. The article is review and analysis of modern facilities for transporting and separating the grain size simultaneously. Exposed advantages and disadvantages of existing structures. A new original conveyor-separator that provides cleaning of grain from large impurities. Application of the new conveyor-separator will reduce grain damage during loading and improve further purification.