Збірники наукових праць ЦНТУ
Permanent URI for this communityhttps://dspace.kntu.kr.ua/handle/123456789/1
Browse
6 results
Search Results
Item Модернізація спеціальної оправки з торцевою фрезою-протяжкою, яка працює за схемою прогресивного фрезерування(ЦНТУ, 2017) Анастасенко, С. М.; Григурко, І. О.; Будуров, В. Л.; Anastasenko, S.; Grigyrkо, І.; Bydyrov, V.У статті представлена модернізація конструкції спеціальної оправки для торцевої фрези зі зміщеним центром обертання. Розроблено схему прогресивного фрезерування поверхонь за допомогою спеціальної оправки для фрези-протяжки, яка забезпечує знімання припуску від 10 до 30 мм за один прохід. The article presents the design upgrading of a special mandrel for a face milling cutter with a displaced center of rotation in order to decrease labor intensity when milling surfaces with large allowances, to reduce the production cost and to increase the cutting power of inserts of the broach milling cutter. An upgraded design of a special mandrel with a displaced center of rotation for the broach milling cutter has been proposed. The design upgrading of the special mandrel with a displaced center of rotation of the cutter for the face broach milling cutter allows to multiply the cutting power of inserts of the broach milling cutter by about 3 times and reduce the labor intensity of manufacturing per part by 4-5 times, which significantly affects the reduction of the unit cost production. A scheme of advanced milling of surfaces with the help of a special mandrel for the broach milling cutter, which ensures the removal of the allowance from 10 to 30 mm in one pass, has been devised.Item Вплив режимів різання на збереження стійкості інструмента : проблеми та шляхи їх вирішення(КНТУ, 2016) Анастасенко, С. М.; Будуров, В. Л.; Григурко, І. О.; Anastasenko, S.; Bydyrov, V.; Grigyrkо, І.У статті визначено вплив чинників на стійкість інструмента. Досліджено наступні чинники: швидкість різання, подача, глибина різання, задній кут, головний кут в плані, допоміжний кут в плані, радіус при вершині, передній кут, змінні багатогранні пластини (ЗБП). Встановлено і систематизовано причини зниження стійкості інструмента та запропоновано шляхи збереження стійкості інструмента. Research of the influence of cutting speed, feeding, cutting depth, end-clearance angle, plan approach angle, minor cutting edge angle, tip radius and the face angle on the tool durability. Materials that are used for manufacturing of cutting tools are expensive. Therefore the cost of cutting tools is rather high, as well as the production cost of goods produced by means of such tools. Thus one has to decide how to reduce manufacturing costs. There are two ways to solve the problem. The first way is to create some new materials to make the cutting tools more resistant than the existing ones, and the second way is to optimize cutting conditions to ensure maximum performance while maintaining the tool durability. The first way is quite long and the cost of the new tools will be not lower than the existing one. The second way is more realistic. The study identified and systematized the factors that affect the tool durability. The study allows to conclude that all cutting parameters in one way or another affect the tool durability and production costs. Therefore the need for compliance of the cutting parameters is crucial for ensuring the stability of the cutting tool, and as much for the competitiveness of products.Item Можливість модернізації механічної обробки багатоступінчастих валів на токарних верстатах застарілої конструкції(КНТУ, 2013) Анастасенко, С. Н.; Григурко, І. О.; Капура, І. А.; Anastasenko, Sergey; Grigyrko, Ivan; Kapyra, ІgorПредставлена модернізація токарних верстатів застарілої конструкції з реконструкцією гідрокопіювальних супортів для обробки багатоступінчастих валів та улаштування для автоматизованого завантаження, закріплення і зняття заготовок. При конструкторській розробці на заводі можливо враховувати виробничі можливості ремонтних і інструментальних цехів, на котрі покладається задача переобладнання верстатів і ретельного розрахунку економічних показів, які визначають рентабельність реконструкції і степені автоматизації. В більшості випадків при автоматизації верстатів для роботи за замкнутим циклом виготовлення простих деталей можемо рекомендувати пневмомеханічні улаштування, комбінуючи механічний барабанний привід супорту з пневматичними затискними улаштуваннями. It is presented the putmoded turn bench with reengineering of hydro-copying carrage for multiplediameters part processing and computerized work pieces loading, fixture and relieving devices. At designer development at the plant it is possible to take into account production mo-zhlivosti of repair and instrumental workshops upon which the task of re-equipment of machine-tools and careful calculation of economic pokazkiv, yaki depends determine profitability of reconstruction and degrees of automation. In most cases during automation of machine-tools for work after the reserved cycle of vigotov-lennya of simple details can recommend the pneumomassage arranging, combining a mechanical drum occasion support from.Item Рідкопластичне формування поверхонь бабітових вкладишів(КНТУ, 2014) Ошовський, В. Я.; Григурко, І. О.; Капура, І. А.; Oshovsky, V.; Grigurko, I.; Kapura, І.Розглянуто рідкопластичне формування поверхонь бабітових вкладишів при безпосередньому їх суміщенні з валом. Доведено, що це покращує збіг геометрії поверхонь їх контакту та підвищує ресурс спряження. The defects of geometry are described for the surfaces of friction of slidewaies from a babbit, which are used in compressors and ICE for agriculture technique. For the increase of resource of machines it is offered to form geometry for the bearing surface of slideway by a billow. For this purpose, surfaces from a babbit in the fluidplastic condition are offered to form by the polished surface of neck of billow. The interval of temperatures for a surface at forming is offered on the basis of analysis of process of crystallization of babbit. The method of heating is offered for formation of rought tolerance for grinding in of bearing surface to the billow. The same forming is recommended to execute and for the bronze bearings of covered preliminary by the layer of babbit. Such treatment of surface liquidates formation on her of regions of enhanceable specific pressure. The results of researches show that, liquidplastic forming in a complex with grinding in allows to increase the resource of compressors or ICE of agricultural technique.Item Модернізація вузлів обладнання для механічної обробки гільзи циліндрів двигуна на токарних верстатах застарілої конструкці(КНТУ, 2015) Анастасенко, С. М.; Григурко, І. О.; Ошовський, В. Я.; Будуров, В. Л.; Anastasenko, Sergey; Grigyrko, Ivan; Ohsovsrsy, Victor; Bydyrov, VasilyУ статті представлена модернізація токарних верстатів застарілої конструкції з реконструкцією гідрокопіювальних супортів для механічної обробки гільзи циліндра двигуна та улаштування для автоматизованого завантаження, закріплення і зняття заготовок. При конструкторській розробці на заводі можливо враховувати виробничі можливості ремонтних і інструментальних цехів, на котрі покладається задача переобладнання верстатів і ретельного розрахунку економічних показників,які визначають рентабельність реконструкції і степені автоматизації. В більшості випадків при автоматизації верстатів для роботи за замкнутим циклом виготовлення простих деталей можемо рекомендувати пневмомеханічні улаштування, комбінуючи механічний барабанний привід супорту з пневматичними затискними улаштуваннями. In article modernization of lathes of an outdated design with reconstruction of hydrocopy calipers is provided for machining of a cylinder liner of the engine and the device for the automated loading, fastening and removal of preparations. At design development at plant it is possible to consider production capabilities of maintenance and tool shops to which the problem of re-equipment of machines and careful calculation of economic indicators which define profitability of reconstruction and extent of automation is assigned. In many cases at automation of machines for work behind the closed cycle production of simple details is recommended the pneumomechanical devices combining a mechanical drum drive gear of a caliper with air clamping devices. Re-equipment of the machine is reduced to installation of tightening cylinders, to production of mandrels and the rotating spindle of the rear grandma. Cylinders and cranes of steering and shops. Lathe productivity with a hydrocopy caliper and loading organization will increase by 10 times equalizing it with a productivity at manual service, and expenses will pay off approximately in three months.Item Вихровий метод фрезерування трапецоїдної різьби(КНТУ, 2009) Григурко, І. О.; Доценко, С. М.Розглянута конструкція пристосування для фрезерування трапецоїдної різьби вихровим методом на ходових гвинтах канатоукладача лебідки. Дана конструкція пристосування підвищить продуктивність праці і дозволить знизити собівартість виробів. The construction adapted for milling trapezium-shaped carvings by the whirlwind method with the help of device for laying rope of the winch has been examined. This construction will increase the labour productivity and reduce the cost of the product.