Збірники наукових праць ЦНТУ
Permanent URI for this communityhttps://dspace.kntu.kr.ua/handle/123456789/1
Browse
2 results
Search Results
Item Уточнений розрахунок котків фрикційних механізмів(ЦНТУ, 2022) Невдаха, Ю. А.; Дубовик, В. О.; Пукалов, В. В.; Невдаха, Н. А.; Можейко, Д. В.; Nevdakha, Yu.; Dubovyk, V.; Pukalov, V.; Nevdakha, N.; Mozheiko, D.Робота фрикційних механізмів заснована на використанні сил тертя, які виникають між його рухомими ланками. Оскільки фрикційні механізми працюють на основі використання сил тертя, то в першу чергу слід визначити величину нормального тиску між котками, необхідну для передачі заданого обертового моменту. Тому в роботі розглядаються і уточнюються кінематичні розрахунки, геометричні і силові параметри варіаторів. Виконується дослідження впливу силових параметрів на працездатність фрикційних передач різних типів та забезпечення їх довговічності. Пропонуються нові підходи до вирішення цих задач. Приводяться рекомендації щодо вибору матеріалів фрикційних котків. As is known, friction mechanisms are used to convert rotational motion between parallel shafts or whose axes intersect with a constant or variable gear ratio. In the latter case, they are called variators. The operation of friction mechanisms is based on the use of friction forces that occur between its moving parts. Since the mechanisms under consideration work on the basis of the use of friction forces, it is clear that first of all it is necessary to determine the amount of normal pressure between the rollers required to transmit a given torque. Therefore, the work unravels and refines the kinematic calculations, geometric and force parameters of the variators. A study of the influence of force parameters on the performance of friction gears of different types and ensuring their durability. New approaches to solving these problems are proposed. Recommendations for the choice of friction roller materials are given. It is stated that the materials for friction rollers must have a high coefficient of friction, contact strength, wear resistance, as well as a high modulus of elasticity to reduce the elastic slip of the rollers.Item До розрахунку міцності різьбових з’єднань(КНТУ, 2016) Невдаха, А. Ю.; Дубовик, В. О.; Nevdaha, А.; Dubovik, V.В статті проведені дослідження метричних різьбових з’єднань, які дозволяють розраховувати коефіцієнт повноти різьби. Це дає можливість збільшити міцність різьбових з’єднань і, як результат, підвищити надійність вузла і машини в цілому. В розрахунках враховували, що сила розподілена по поверхні витка і прикладена в центрі ваги його робочої поверхні. При цьому враховували зусилля, яке руйнує тіло болта, а також силу зрізу різьби болта і зусилля зрізу витка гайки. З отриманих рівнянь зрізу для витків болта і гайки визначили коефіцієнт повноти різьби. В результаті проведених досліджень були отримані умови рівноміцності стержня болта і різьби гайки. Із співвідношень для метричних стандартних різьб і однакових матеріалів болта та гайки визначили висоту гайки, яка відповідає висоті стандартних гайок. The paper studies metric threaded connections which allow to calculate the coefficient of completeness thread. This makes it possible to increase the strength of threaded connections and as a result increase the reliability of the site and the car in general. The calculations take into account that the force is distributed over the surface of the coil and attached to the center of gravity of its working surface. This took into account the efforts that destroys the body bolt and screw thread cut power and effort slice spiral nuts. From these equations for cut turns the bolt and nut factor determined completeness thread. As a result of the research were obtained conditions rivnomitsnosti rod bolt and nut thread. With relations for metric standard thread and the same material bolt nuts and nut height determined which corresponds to the height standard screws.