Збірники наукових праць ЦНТУ
Permanent URI for this communityhttps://dspace.kntu.kr.ua/handle/123456789/1
Browse
3 results
Search Results
Item До розрахунку зубців прямозубих циліндричних передач на згин(ЦНТУ, 2020) Невдаха, Ю. А.; Дубовик, В. О.; Невдаха, Н. А.; Златопольський, Ф. Й.; Nevdakha, Yu.; Dubovyk, V.; Nevdakha, N.; Zlatopolskiy, F.; Дубовик, В. А.; Златопольский, Ф. И.В роботі аналізуються розрахункові схеми циліндричної прямозубої передачі на згин зубців. Розглядається найбільш поширена розрахункова схема злому зубця, де небезпечний переріз злому зуба відбувається у основі ножки вище кола діаметра западини зубців. На практиці реальний же злом зубця лежить нижче діаметра западини зубців і має опуклу форму перерізу. Для більш точного розрахунку зубців на згин досліджували коефіцієнт форми зубців. В результаті встановлено, що коефіцієнт форми зуба зменшується зі збільшенням кількості зубців. The aim of the work is to improve the calculations of spur cylindrical wheels per bend, due to the fact that the existing formulas do not give the actual value of the maximum stress, and the diagram does not correspond to the real law of stress distribution. In order to obtain satisfactory results, it is more correct to calculate the teeth at the maximum local stress. Combining the coefficients and substantiating the calculated dependence to determine the value of the coefficient of the shape of the tooth under load, applied at any point of the working profile of the tooth, to obtain formulas for the bending strength of the teeth of the gear and wheel. When calculating the bending teeth, the calculation is based on the stresses arising at the base of the tooth, under the load applied at the top of the tooth. Consider first the most common calculation scheme. Dangerous section of the tooth as seen from the plot of total stresses indicates that the maximum normal stress occurs on the non-working side of the tooth - the compression side, however, since fatigue cracks occur at the base of the tooth on the stretching side, the calculation is based on tensile stress on the working side. The hypothesis of non-curvature of flat sections is unfair for short beams of variable cross section, so the total diagram does not correspond to the real law of stress distribution. But at the base of the tooth near the transition curve is the place of stress concentration. The actual dangerous cross-section lies below the cross-section of the depression, this is confirmed by the fact that the fatigue cracks form an angle with the load curve close to straight, and the fracture of the tooth has a convex shape. In this case, it is more correct to calculate the teeth at the maximum local stress. Combining the coefficients obtained a calculated dependence to determine the value of the coefficient of the shape of the tooth under load, applied at any point of the working profile of the tooth. As a result of the study it was found that the coefficient of tooth shape decreases with increasing number of teeth. This result was expected because as the number of teeth increases, the angle between the teeth decreases, and neighboring teeth perceive part of the stress that occurs in the loaded tooth. The formulas for checking the bending strength of gear teeth and wheels are obtained. The above refinement calculations of the teeth on the bend reflect the beneficial effect of improving the accuracy of the manufacture of teeth. В работе анализируются расчетные схемы цилиндрической прямозубой передачи на изгиб зубцов. Рассматривается наиболее распространенная расчетная схема излома зубцов, где опасное сечение излома зубьев происходит в основе ножки выше круга диаметра впадины зубцов. На практике реальный же излом зубьев лежит ниже диаметра впадины зубьев и имеет выпуклую форму сечения. Для более точного расчета зубьев на изгиб исследовали коэффициент формы зубьев. В результате установлено, что коэффициент формы зуба уменьшается с увеличением количества зубьев.Item Определение соотношения между прогибом нейтральной оси и образующей при деформации осесимметричных тел(КНТУ, 2013) Пукалов, В. П.; Пукалов, В. В.; Петренко, Н. Н.; Златопольский, Ф. И.; Pukalov, V.; Petrenko, N.; Zlatopolskyy, F.; Златопольський, Ф. Й.; Петренко, М. М.На основе метода начальных параметров разработана математическая модель деформации образующей цилиндрической поверхности калиброванных валков, лежащих на двух шарнирных опорах. Полученный результат позволяет оптимизировать разработку процесса сортовой прокатки с заданной точностью. На основі методу початкових параметрів розроблена математична модель деформації створюючої циліндрової поверхні каліброваних валків, що лежать на двох шарнірних опорах. Отриманий результат дозволяє оптимізувати розробку процесу сортового прокатування із заданою точністю. The purpose of work is a calculation of betweenness bending of neutral axis and formative axisymmetrical bodies – rollers, in the process of rolling. On the basis of method of initial parameters the mathematical model of deformation of formative cylindrical surface of the calibrated rollers, lyings on two joint supports is developed. The got result allows to optimize development of process of high quality rolling with the set exactness.Item Определение прогиба образующей цилиндрической поверхности и нейтральной оси при деформации осесимметричных тел(КНТУ, 2013) Пукалов, В. П.; Пукалов, В. В.; Златопольский, Ф. И.; Петренко, Н. Н.; Pukalov, V.; Zlatopolskyy, F.; Petrenko, N.; Златопольський, Ф. Й.; Петренко, М. М.На основе теории упругости двумерной задачи получено уравнение определяющее соотношение между прогибом нейтральной оси образующей цилиндрической поверхности калиброванных валков, опирающихся на две шарнирные опоры и нагруженных сосредоточенной силой в произвольном сечении. Установлено, что прогиб образующей цилиндрической поверхности меньше, чем прогиб нейтральной оси. Эта разница в случае коротких валков, может достигать до 11,25%. На основі теорії пружності двовимірного завдання отримано рівняння визначальне співвідношення між прогином нейтральної осі створюючої циліндрової поверхні каліброваних валків, які спираються на дві шарнірні опори і навантажених зосередженою силою в довільному перерізі. Встановлено, що прогин створюючої циліндрової поверхні менший, ніж прогин нейтральної осі. Ця різниця в разі коротких валків, може досягати до 11,25%. The purpose of work is a calculation of difference of bending between a formative cylindrical surface and bending of neutral axis during deformation of axisymmetrical bodies. On the basis of theory of resiliency of two-dimensional task equalization is got determining betweenness bending of neutral axis of formative cylindrical surface of the calibrated rollers, leanings against two joint supports and loaded with the concentrated force in an arbitrary section. It is set that bending of formative cylindrical surface less than, than bending of neutral axis. This difference in the case of short rollers, can arrive at to 11,25%.