Збірники наукових праць ЦНТУ
Permanent URI for this communityhttps://dspace.kntu.kr.ua/handle/123456789/1
Browse
2 results
Search Results
Item Дослідження процесу затвердіння та прогнозування структури литих чавунних молольних тіл(ЦНТУ, 2018) Ломакін, В. М.; Клименко, В. В.; Пукалов, В. В.; Кузик, О. В.; Дубодєлов, В. І.; Горюк, М. С.; Ломакин, В. Н.; Кузык, А. В.; Дубоделов, В. И.; Lomakin, V.; Klymenko, V.; Pukalov, V.; Kuzyk, O.; Dubodelov, V.; Goriuk, M.Розглядається використання методу скінченних елементів для чисельного розрахунку процесу затвердіння виливків молольних тіл циліндричної і сферичної форми в кокілі в залежності від хімічного складу сплаву та для прогнозування співвідношення між кількістю ледебуриту, що визначає зносостійкість молольних тіл, та кількістю аустеніто-графітної евтектики. Рассматривается использование метода конечных элементов для численного расчета процесса затвердевания отливок мелющих тел цилиндрической и сферической формы в кокиле в зависимости от химического состава сплава и для прогнозирования соотношение между количеством ледебурита, что определяет износостойкость мелющих тел, и количеством аустенито-графитный эвтектики. The aim of the study was to calculate the kinetics of crystallization and to determine the rational mode for cooling castings of a crushing cylinder and a crushing ball in metallic form to ensure that the surface wear-resistant bleached layer does not have more than a third of the size (or radius of the ball) from the surface of the body. The use of the finite element method for numerical calculation of solidification of castings of grinding bodies of cylindrical and spherical bodies in chill molds is considered depending on the chemical composition of the alloy and for predicting the ratio between the amount of ledeburite, which determines the wear resistance of grinding bodies, and the amount of austenite-graphite eutectic. The experimental chemical composition of cast iron for grinding bodies: 3-3.9% C, 2.8-4% Si, 0.6-1.2% Mn; less 0.03% P, less 0,02% S. For cylindrical and spherical bodies, the thermal conductivity functional was obtained and the kinetics of crystallization of castings was calculated. The data obtained indicate an inhomogeneity in the distribution of the linear rate of solidification along the cross-section of cast products. At the beginning of the process, the solidus front has a relatively high velocity (0.08 mm / s), which rapidly decreases with increasing thickness of the crust. Further, with the passage of time, the thickness of the two-phase zone gradually decreases and in the central part of the casting the rate of solidification is ~ 0.005 mm / sec. It is established that the microstructure of low-chromium cast iron (~ 1% Cr) is perlite-ledeburite. The carbide phase is represented by doped cementite (Fe, Cr)3С. A comparative analysis of the operational properties and the cost of their achievement showed that in today's conditions, it is a compromise to make cast grinding bodies from low-alloyed cast iron (0.8-1% Cr). The data obtained by the calculation method are in good agreement with the results of production tests of cast grinding bodies, which made it possible to optimize the technology for manufacturing such products.Item Дослідження впливу кінетики кристалізації на властивості кокільних виливків чавунних цильпебсів(КНТУ, 2016) Ломакін, В. М.; Клименко, В. В.; Пукалов, В. В.; Ломакін, А. В.; Lomakin, Viktor; Klimenko, Vasil; Pukalov, Viktor; Lomakin, AndriyРозглядається використання методу математичного моделювання для визначення часу початку і закінчення процесу кристалізації легованих чавунів у кокілі в залежності від хімічного складу сплаву та для прогнозування співвідношення між кількістю ледебуриту, що визначає зносостійкість цильпебсів (молольних циліндрів), та кількістю аустеніто-графітної евтектики. The aim of this work is studying how speed of hardening and chromium's modified additives affect to structure of cast iron's cylinder in metallic form for rising of the shock and abrasive durability. Here is examined use of mathematical modeling to identify the start time and end time of hardening alloying metal, depending on the chemical composition of the alloy, and to predict the ratio between amount of ledeburite, which determines the durability of the cylinder, and number of austenite-graphite eutectic. Comparative analysis of performance properties and value of its achievements showed that today the best compromise is to manufacture grinding bodies from cast iron . The cast iron has to be low alloyed by the chromium(0.8-1%).