Збірники наукових праць ЦНТУ
Permanent URI for this communityhttps://dspace.kntu.kr.ua/handle/123456789/1
Browse
3 results
Search Results
Item Аналіз енергетичних характеристик турбомеханізмів(ЦНТУ, 2017) Лобов, В. Й.; Митрофанов, О. В.; Lobov, V.; Mitrofanov, A.Показано, що турбомеханізмиє енергоємними в порівняні з іншими технологічними об’єктами і агрегатами підприємства. Виконано порівняння втрат споживання електричної енергії вентиляторами, використовуючи паспортну номінальну корисну гідравлічну потужність з одної сторони івраховуючи,з іншої сторони,максимальні та мінімальні значення статичних коефіцієнтів корисної дії, статичного тиску та обсяги повітря, що відповідають значенням параметрів вентилятора в точках характеристик. При цьому розрахунок виконано для 25 режимів. Надані результати виконаних розрахунків, які визначають залежність енергоспоживання турбомеханізмами, які залежать від технічних параметрів і режимів роботи та може змінюватися в десятки разів. The purpose of this article is to analyze the characteristics of electrical power of turbo-mechanisms at work in different modes and loads, to establish the power consumption of equipment and find the ways to reduce it. The comparison of electrical power loss consumption of fans using the nameplate nominal effective hydraulic power on the one hand and the maximum and minimum values of the static efficiency coefficient, static pressure and air volume corresponding to the values of fan parameters in the characteristic points on the other hand is carried out. The calculation is performed for 25 modes. The results of the calculations which determine the dependence of turbo-mechanisms energy on technical parameters and operating conditions may ten times vary. To define real power consumption of turbo-mechanisms we should take into account the most rational and possible modes of its operation.To calculate power intensity, defined in the normal turbo-mechanisms operating modes, we must use the minimum and maximum values of static efficiency, static pressure and air volume corresponding to the values of fan parameters performance.In this case we should perform the calculation for the 25 modes.The results of the study prove the dependence of turbo-mechanisms power of technical parameters and operating conditions which may vary by tens of times; therefore, it requires further investigation of equipment automation and devices for its saving.Item Застосування новітніх технологій висіву просапних культур(КНТУ, 2014) Лобов, В. Й.; Дубовик, І. І.; Lobov, Vyacheslav; Dubovik, ІgorДля досягнення оптимальних показників при виконанні сукупних механізованих технологічних операцій за допомогою сільськогосподарської сівалки запропоновано узагальнену схему, яка дозволяє керувати у реальному часі сівалкою з достовірною інформацією про стан посівного поля і машино- тракторного агрегату. To achieve optimum performance when performing comprehensive mechanized process operations using agricultural sowing proposed generalized scheme, which allows you to manage real-time drill with accurate information about the state of the field and sowing machinery tractor unit. Proposed to use the method of operation in which the determined temperature, humidity and humus content in the soil, with subsequent correction executive signals depending on the values of these parameters. The combination of location characteristics defined temperature and humidity settings furrow and the real state of agricultural fields which are defined thermographic device with built-in digital camera, in the mathematical aspect is a scalar quantity in a two-dimensional grid coordinate plane.Item Спосіб сівби насіння просапних сільськогосподарських культур(КНТУ, 2015) Лобов, В. Й.; Vyacheslav, LobovНаведено спосіб висіву насіння, який полягає у визначені в атмосферному повітрі фізико- хімічних властивостей сільськогосподарського пилу - ґрунтову дефляцію, який виникає в робочій зоні при переміщені сівалки, обчислюють гігроскопічність цього пилу, по якому визначають вологість ґрунту, і в залежності від її рівня автоматично керують виконавчими механізмами сошників, наприклад гідроциліндрами, які регулюють потрібні глибини борозен для закладання в них насіння та визначають зусилля для ущільнення борозн, а по коефіцієнту спектральної яскравості сільськогосподарського пилу розраховують гумусові речовини ґрунту та керують потоками водяного розчину добрив і стимуляторів росту. Для пояснення надана блок-схема системи керування сівалкою, яка реалізує запропонований спосіб висіву насіння. The paper presents that to improve the accuracy of seeding and maximum field germination of seeds is necessary to consider the heterogeneity of soil properties, such as its moisture on the length of the rut. This is especially important in modern technology planting row crops is accompanied by a significant increase in performance and speed drills by sowing the field. Given way to seed, which is to determine the properties of the agricultural dust - dirt deflation, which occurs when you move the drill, this is calculated hygroscopic dust, which determine soil moisture, and depending on its level is automatically controlled actuators openers regulators need to lay the depth of furrows in their seeds. The method comprises creating sowing furrows in the soil, feeding them through the seed opener and seal grooves, while additionally provide training seed, combining it with the seed in the furrow by mixing in the opener seed flow with the flow of aqueous solution of fertilizers and growth stimulants and seal combine with the feeding grooves in them and the total flow of seed and fertilizer aqueous growth stimulants planting depth of soil moisture by intensive water, and further working area in the air seeder measuring physic-chemical properties of the agricultural dust (dust soil deflation), which occurs when moved sowing unit. Calculate the hygroscopicity of the dust, which determine the soil moisture content, and depending on its level is automatically controlled actuators sowing coulters, for example, hydraulic cylinders that regulate the depth of the furrows need for seeding. In the seed furrow portion of the water introduced to bring the soil moisture to an optimum state, provides the necessary seed germination if the soil moisture, calculated on the basis of its measurements before and during sowing of seed, less than critical, and determine the coefficient of the spectral brightness agricultural dust (soil dust deflation), which is calculated by soil holmic substances. Depending on the level of control actuators that regulate the flow of organic matter in the grooves, which are necessary for plants to provide the desired fertility. There is provided a block diagram of a control system drill, which realizes the proposed method for seeding.