Збірники наукових праць ЦНТУ
Permanent URI for this communityhttps://dspace.kntu.kr.ua/handle/123456789/1
Browse
7 results
Search Results
Item Визначення запасу міцності деталей при нестандартній зміні напружень(ЦНТУ, 2024) Невдаха, Ю. А.; Пукалов, В. В.; Пирогов, В. В.; Невдаха, Н. А.; Васильковський, М. О.; Nevdakha, Yu.; Pukalov, V.; Pirogov, V.; Nevdakha, N.; Vasylkovskyi, M.В сучасному машинобудуванні широко використовують машини, механізми, верстати та інше обладнання, яке працює при змінних навантаженнях. Під час виконання роботи від дії змінних навантажень в деталях машин відповідно виникають і зміні напруження. Невірно визначений запас міцності деталей при нестандартній зміні напружень призведе до поломок та руйнування, а також і аварій машин. Таким чином виникає необхідність в більш точному визначенні запасу міцності у деталях, в яких максимальні напруження циклу, змінюються за ступінчастим законом. In modern mechanical engineering, the search for machines, mechanisms, machine tools and other equipment that works under variable loads is widely conducted. During work from the actions of variable loads in machine parts according to the result and changes in stress. Incorrectly defined margin of safety of parts with non-standard changes will lead to breakdowns and destruction, as well as machine accidents. Thus, a more precisely defined safety margin is required in parts in which the maximum stress cycles vary according to a step law. The purpose of the article is to study the processes of a non-standard mode of voltage change, which change according to a step law and receive the number of cycles after which the destruction of the part occurs. The task takes place in the investigated values of the equivalent stress, according to the parameters of which the coefficient of production of the safety margin under the action of non-standard stresses.Item Уточнений розрахунок котків фрикційних механізмів(ЦНТУ, 2022) Невдаха, Ю. А.; Дубовик, В. О.; Пукалов, В. В.; Невдаха, Н. А.; Можейко, Д. В.; Nevdakha, Yu.; Dubovyk, V.; Pukalov, V.; Nevdakha, N.; Mozheiko, D.Робота фрикційних механізмів заснована на використанні сил тертя, які виникають між його рухомими ланками. Оскільки фрикційні механізми працюють на основі використання сил тертя, то в першу чергу слід визначити величину нормального тиску між котками, необхідну для передачі заданого обертового моменту. Тому в роботі розглядаються і уточнюються кінематичні розрахунки, геометричні і силові параметри варіаторів. Виконується дослідження впливу силових параметрів на працездатність фрикційних передач різних типів та забезпечення їх довговічності. Пропонуються нові підходи до вирішення цих задач. Приводяться рекомендації щодо вибору матеріалів фрикційних котків. As is known, friction mechanisms are used to convert rotational motion between parallel shafts or whose axes intersect with a constant or variable gear ratio. In the latter case, they are called variators. The operation of friction mechanisms is based on the use of friction forces that occur between its moving parts. Since the mechanisms under consideration work on the basis of the use of friction forces, it is clear that first of all it is necessary to determine the amount of normal pressure between the rollers required to transmit a given torque. Therefore, the work unravels and refines the kinematic calculations, geometric and force parameters of the variators. A study of the influence of force parameters on the performance of friction gears of different types and ensuring their durability. New approaches to solving these problems are proposed. Recommendations for the choice of friction roller materials are given. It is stated that the materials for friction rollers must have a high coefficient of friction, contact strength, wear resistance, as well as a high modulus of elasticity to reduce the elastic slip of the rollers.Item Збільшення запасу міцності різьбових з’єднань, що працюють при змінних навантаженнях(ЦНТУ, 2022) Невдаха, Ю. А.; Пирогов, В. В.; Невдаха, Н. А.; Олійніченко, Л. С.; Васильковський, М. О.; Nevdakha, Yu.; Pirogov, V.; Nevdakha, N.; Olijnichenko, L.; Vasylkovsky, M.В останні часи ми бачимо зростання цікавості конструкторів до розрахунків різьбових з’єднань, що працюють при змінних напруженнях. Це пояснюється тим, що у більшості механізмів, зокрема автомобілебудівної галузі, різьбові з’єднання працюють при змінних напруженнях, але невірно визначений запас міцності різьбових з’єднань призводить до поломок та руйнування механізмів. Виникає необхідність в дослідженні більш точних розрахункових формул для визначення запасу міцності різьбових з'єднань, що і є результатом перевірочного розрахунку. One of the most common types of plug-in connections are threaded connections. In any machine, unit, the number of parts of threaded connections (bolts, studs, nuts, washers, etc.) is calculated by dozens and hundreds of pieces. It follows from this that the issue of designing and calculating threaded connections is of great importance in the design of machines and devices. One of the most important elements of bolts and screws is the thread, which is the surface of the protrusion formed during the helical movement of an arbitrary flat contour on the side surface of a cylinder or cone. Threaded connections are widely used in various mechanisms (internal combustion engines, etc. products). Their use is due to simplicity, high load-bearing capacity, reliability, as well as the convenience of connecting and disconnecting parts. The calculation of tightened threaded connections operating under alternating stresses is a check calculation. Based on the simplified statement of the problem, the preliminary dimensions of the main elements of the threaded connection are determined. Then the layout of the connecting node is carried out, and after the design is fully determined, they begin to perform the verification calculation. In recent times, we have seen an increase in the interest of designers in the calculations of threaded connections operating under variable stresses. This is explained by the fact that in most mechanisms, in particular in the automotive industry, threaded connections work under variable stresses, but an incorrectly determined margin of strength of threaded connections leads to breakdowns and destruction of mechanisms. Thus, there is a need to study more accurate calculation formulas for determining the margin of strength of threaded connections, which is the result of a verification calculation.Item До розрахунку зубців прямозубих циліндричних передач на згин(ЦНТУ, 2020) Невдаха, Ю. А.; Дубовик, В. О.; Невдаха, Н. А.; Златопольський, Ф. Й.; Nevdakha, Yu.; Dubovyk, V.; Nevdakha, N.; Zlatopolskiy, F.; Дубовик, В. А.; Златопольский, Ф. И.В роботі аналізуються розрахункові схеми циліндричної прямозубої передачі на згин зубців. Розглядається найбільш поширена розрахункова схема злому зубця, де небезпечний переріз злому зуба відбувається у основі ножки вище кола діаметра западини зубців. На практиці реальний же злом зубця лежить нижче діаметра западини зубців і має опуклу форму перерізу. Для більш точного розрахунку зубців на згин досліджували коефіцієнт форми зубців. В результаті встановлено, що коефіцієнт форми зуба зменшується зі збільшенням кількості зубців. The aim of the work is to improve the calculations of spur cylindrical wheels per bend, due to the fact that the existing formulas do not give the actual value of the maximum stress, and the diagram does not correspond to the real law of stress distribution. In order to obtain satisfactory results, it is more correct to calculate the teeth at the maximum local stress. Combining the coefficients and substantiating the calculated dependence to determine the value of the coefficient of the shape of the tooth under load, applied at any point of the working profile of the tooth, to obtain formulas for the bending strength of the teeth of the gear and wheel. When calculating the bending teeth, the calculation is based on the stresses arising at the base of the tooth, under the load applied at the top of the tooth. Consider first the most common calculation scheme. Dangerous section of the tooth as seen from the plot of total stresses indicates that the maximum normal stress occurs on the non-working side of the tooth - the compression side, however, since fatigue cracks occur at the base of the tooth on the stretching side, the calculation is based on tensile stress on the working side. The hypothesis of non-curvature of flat sections is unfair for short beams of variable cross section, so the total diagram does not correspond to the real law of stress distribution. But at the base of the tooth near the transition curve is the place of stress concentration. The actual dangerous cross-section lies below the cross-section of the depression, this is confirmed by the fact that the fatigue cracks form an angle with the load curve close to straight, and the fracture of the tooth has a convex shape. In this case, it is more correct to calculate the teeth at the maximum local stress. Combining the coefficients obtained a calculated dependence to determine the value of the coefficient of the shape of the tooth under load, applied at any point of the working profile of the tooth. As a result of the study it was found that the coefficient of tooth shape decreases with increasing number of teeth. This result was expected because as the number of teeth increases, the angle between the teeth decreases, and neighboring teeth perceive part of the stress that occurs in the loaded tooth. The formulas for checking the bending strength of gear teeth and wheels are obtained. The above refinement calculations of the teeth on the bend reflect the beneficial effect of improving the accuracy of the manufacture of teeth. В работе анализируются расчетные схемы цилиндрической прямозубой передачи на изгиб зубцов. Рассматривается наиболее распространенная расчетная схема излома зубцов, где опасное сечение излома зубьев происходит в основе ножки выше круга диаметра впадины зубцов. На практике реальный же излом зубьев лежит ниже диаметра впадины зубьев и имеет выпуклую форму сечения. Для более точного расчета зубьев на изгиб исследовали коэффициент формы зубьев. В результате установлено, что коэффициент формы зуба уменьшается с увеличением количества зубьев.Item Загальні підходи до оцінки дотримання підприємством принципу безперервності діяльності(КНТУ, 2006) Невдаха, Н. А.Розглянуто проблемні питання оцінки дотримання підприємством принципу безперервності діяльності. Запропоновано напрямки визначення аналітичних процедур на даному етапі аудиторської перевірки. The problem questions of estimation of maintenance by the enterprise of principle of continuity of activity are considered and offered definite analytical procedures on the given stage of public accountant verificationItem Теоретичні засади аудиту фінансового стану підприємства(КНТУ, 2005) Шалімова, Н. С.; Невдаха, Н. А.Досліджуються проблеми теорії і практики проведення аудиту фінансового стану підприємства в сучасних умовах. Запропонована модель аудиту фінансового стану, яка включає такі елементи як об‘єкти аудиту, критерії ефективності, методи отримання аудиторських доказів.The problems of theory and practice of audit of enterprise`s financial state under present-day conditions are investigated. The model of financial state audit which cosists of such elements as objects of the audit, creterion of the effectivness, methods of achieving the audit evidence is proposed.Item Фінансовий аналіз як складова аналізу господарської діяльності підприємства(КНТУ, 2009) Невдаха, Н. А.; Nevdaha, N.У статті досліджено на основі вітчизняних та зарубіжних наукових джерел роль та місце фінансового аналізу в аналізі господарської діяльності підприємства. Розглянуті основні групи користувачів аналітичним матеріалом та їх інформаційні потреби. In the article a role and place of financial analysis in the economic analysis of enterprise is explored on the basis of home and foreign scientific sources. The basic groups of users by analytical material and their informative necessities are considered.