Збірники наукових праць ЦНТУ
Permanent URI for this communityhttps://dspace.kntu.kr.ua/handle/123456789/1
Browse
5 results
Search Results
Item Моніторинг технічного стану ЗПРК за керівними матеріалами на їх експлуатацію(ЦНТУ, 2022) Новицький, А. В.; Nоvitskiy, A.В статті представлено моніторинг інструкцій з обслуговування та експлуатації машин, керівних матеріалів на використання з позиції їх інформативності щодо реалізації вимог надійності. Моніторинг технічного стану проводився для зарубіжних зразків засобів для приготування і роздавання кормів з горизонтальними змішувально-подрібнювальними механізмами. Проаналізовано механізми з позицій наявності інформації про особливості конструкції, характерні несправності та відмови, основні способи відновлення працездатності. Забезпечення надійності включає кілька напрямків діяльності на протязі всіх життєвих циклів. Встановлені основні положення для оцінки технічного стану та підвищення надійності машин при використанні керівних матеріалів. До складу положень входять: інформація про показники надійності машин, механізмів, робочих органів; періодичність технічного обслуговування і ремонту машин, відновлення робочих органів; відомості про трудомісткість технічного обслуговування і ремонту машин, відновлення робочих органів; схеми монтажу-демонтажу механізмів; інформація про характерні відмови та послідовність їх усунення; інформація про критерії граничного стану; технології відновлення робочих органів; інформація про вимоги при встановлення на зберігання. The efficiency of use and increase the reliability of agricultural machinery depends on the regulatory and technical documentation governing the requirements for its technical condition and operation. The analysis of the existing normative-technical and guiding documents on ensuring the reliability of means for preparation and distribution of fodder is given. To effectively carry out maintenance and repair of means for the preparation and distribution of feed should know: the criteria for disability; maximum and permissible parameters of technical condition; indicators of the transition of equipment from working to inoperable condition. The article presents the monitoring of instructions for maintenance and operation of machines, guide materials for use from the standpoint of their informativeness on the implementation of reliability requirements. Monitoring of technical condition was carried out for foreign samples of means for preparation and distribution of feed with horizontal mixing and grinding mechanisms. The mechanisms are analyzed from the standpoint of the availability of information about the features of the structure, the characteristic faults and failures, the main ways to restore efficiency. Ensuring reliability includes several activities throughout the life cycle. The main provisions for assessing the technical condition and improving the reliability of machines when using guide materials. The provisions include: information on the reliability of machines, mechanisms, working bodies; periodicity of maintenance and repair of machines, restoration of working bodies; information on the complexity of maintenance and repair of machines, restoration of working bodies; schemes of assembly and disassembly of mechanisms; information on typical failures and the sequence of their elimination; information on the limit state criteria; technologies for the restoration of working bodies; information on installation requirements. The current normative documents of the system of general technical requirements for the means for the preparation and distribution of feed do not fully meet the organizational and methodological aspects of ensuring their reliability.Item Методичні підходи до формування програми забезпечення надійності сільськогосподарської техніки(ЦНТУ, 2022) Новицький, А. В.; Nоvitskiy, A.Представлені етапи Програми забезпечення надійності засобів для приготування і роздавання кормів на стадії експлуатації та обслуговування. Встановлені основні складові етапів реалізації Програми забезпечення надійності. Підтверджена необхідність дослідження експлуатаційної надійності машин як складних технічних систем з використанням кількісних методів розрахунку. Визначені рекомендації для підвищення надійності засобів для приготування і роздавання кормів: підготовка персоналу який займається їх монтажем та експлуатацією, технічним обслуговуванням та ремонтом; організація системи збирання інформації про надійність; забезпечення системи технічного обслуговування і ремонту; дослідження причин відмов відремонтованих об’єктів; функціонування автоматизованого контролю технічного стану об’єкту. Modern trends in agriculture involve the use of the latest reliable equipment. The specified requirements are met by samples of equipment manufactured by well-known global and domestic machine-building plants. A part of the agricultural machinery market of Ukraine is occupied by means for preparing and distributing fodder. The effectiveness of the use of agricultural machinery depends on the existing regulatory and technical documentation for its operation and measures to ensure reliability. The purpose of the research is to increase the efficiency of the operation of agricultural machinery due to the formation and implementation of the Program for ensuring its reliability. The stages of the Program for ensuring the reliability of means for preparing and distributing fodder at the stage of operation and maintenance are presented. The main components of the implementation stages of the Reliability Assurance Program have been established. The need to study the operational reliability of machines as complex technical systems using quantitative calculation methods is confirmed. Recommendations for increasing the reliability of means for preparing and distributing fodder are defined: training of personnel engaged in their installation and operation, maintenance and repair; organization of the reliability information collection system; maintenance and repair system provision; research into the causes of failures of repaired objects; functioning of the automated control of the facility's technical condition.Item Дослідження процесу теплопередачі в циліндрах двигуна внутрішнього згоряння(ЦНТУ, 2020) Сиволапов, В. А.; Новицький, А. В.; Хмельовський, В. С.; Бистрий, О. М.; Suvolapov, V.; Novitskiy, A.; Khmelevski, V.; Bustruy, O.; Новицкий, А. В.; Хмелёвский, В. С.; Быстрый, А. Н.В статі проведено аналіз наукових публікацій і літературних досліджень процесів теплопередачі в циліндрах двигунів внутрішнього згоряння. Представлено дослідження температурних полів в двигунах під час їх роботи на різних режимах з використанням програмного комплексу та розрахункового модуля. Проаналізовано результати моделювання та проведення термометрування в однорідній і пластинуваній гільзах циліндрів двигунів. Приведено графічні залежності та розподіл температури по товщині стінки циліндра під час максимальної і мінімальної температури на поверхні циліндра. На основі досліджень встановлено, що при пластинуванні і запресуванні вставки температурні поля в циліндрі двигуна змінюються, підвищується температура на внутрішній поверхні циліндра при пластинуванні на 6,5 С, а при запресуванні – на 4,5 С. Це пояснюється тим, що контактний шар при пластинуванні знаходиться в зоні нестаціонарного режиму, а при запресуванні контактний шар знаходиться в зоні стаціонару і, таким чином, збільшує товщину циліндра на 2 міліметри. Встановлено, що різниця мінімальної і максимальної температур на внутрішній поверхні циліндра практично залишається такою ж як у однорідного циліндра. The article analyzes scientific publications and literary studies of heat transfer processes in cylinders of internal combustion engines. The research of temperature fields in engines during their operation at different modes with the use of a software package and calculation module is presented. The results of modeling and thermo-metering in homogeneous and laminated engine cylinder liners are analyzed. Graphic dependencies and temperature distribution by cylinder wall thickness at maximum and minimum temperature on cylinder surface are given. On the basis of researches it is established that at laminating and pressing of inserts temperature fields in the engine cylinder change, temperature on an internal surface of the cylinder increases at laminating on 6,5 °С, and at pressing - on 4,5 °С. This is explained by the fact that the contact layer during plastification is in the zone of non-stationary mode, and when pressing the contact layer is in the zone of stationary mode and thus increases the thickness of the cylinder by 2 millimeters. It is established that the difference of minimum and maximum temperatures on the inner surface of the cylinder practically remains the same as that of a homogeneous cylinder. Thus, modeling becomes the most effective scientific tool in the development and implementation of long-term evaluation of options for improving ICE. В статье проведен анализ научных публикаций и литературных исследований процессов теплопередачи в цилиндрах двигателей внутреннего сгорания. Представлены исследования температурных полей в двигателях во время их работы на различных режимах с использованием программного комплекса и расчетного модуля. Проанализированы результаты моделирования и проведения термометрирования в однородной и пластинированной гильзах цилиндров двигателей. Приведены графические зависимости и распределение температуры по толщине стенки цилиндра при максимальной и минимальной температуры на поверхности цилиндра. На основании исследований установлено, что при пластинировании и запрессовке вставки температурные поля в цилиндре двигателя меняются, повышается температура на внутренней поверхности цилиндра при пластинировании на 6,5 °С, а при запрессовке – на 4,5 °С. Это объясняется тем, что контактный слой при пластинировании находится в зоне нестационарного режима, а при запрессовке контактный слой находится в зоне стационара и, таким образом, увеличивает толщину цилиндра на 2 миллиметра. Установлено, что разница минимальной и максимальной температур на внутренней поверхности цилиндра практически остается такой же как у однородного цилиндра.Item Оцінка надійності системи «людина-машина» в умовах зниження рівня її працездатності й удосконаленні складової «людина-оператор»(КНТУ, 2013) Бойко, А. І.; Новицький, А. В.; Банний, О. О.; Boyko, A.; Nоvitskiy, A.; Bannyi, O.Розроблена стохастична модель і проведено аналіз системи «Людина-Машина». Отримана модель для визначення ймовірності безвідмовної роботи системи для умови підвищення професійного та психофізіологічного рівня оператора. The aim of the presented paper is to elucidate the changes in the probability of failure-free operation of the "human-machine". A stochastic model and carried out a systematic analysis of the "human-machine" the accumulation of failures. The resulting differential equations of dynamic balance of probabilities states of the system. An analytical dependence for the determination of the probability of system failure in the process of "aging" of the machine and the professional and psycho-physiological level operator.Item Дослідження ремонтопридатності кормодробарок(КНТУ, 2006) Бойко, А. І.; Новицький, А. В.; Карабиньош, С. С.В статті представлено результати дослідження ремонтопридатності кормодробарок, визначено якісні та кількісні їх показники. There is considered the results of investigation of food crusher’s reaper reparability and were fined values quantities and qualities in the article.