Збірники наукових праць ЦНТУ
Permanent URI for this communityhttps://dspace.kntu.kr.ua/handle/123456789/1
Browse
16 results
Search Results
Item Surface Topography of Arc-Sprayed Coatings by Cored Wires of Different Compositions and Its Influence on the Wear Mechanism(ЦНТУ, 2025) Hvozdetskyi, V.; Lukyanenko, A.; Markovych, S.; Student, M.; Zadorozhna, Kh.; Mozola, N.; Гвоздецький, В. М.; Лук`яненко, О. Г.; Маркович, С. І.; Студент, М. М.; Задорожна, Х. Р.; Моцола, Н. З.The purpose of this work is to study the influence of the components of the composition of powder wires on the surface characteristics of sanded electric arc coatings. For the application of coatings used electric spray and powder wires with a diameter of 1.8 mm containing powders FeSi, FeTi, FeMn, pure metals Al and Cr and carbide B4C with a filling factor reached 24%. Spray parameters: current – 150 A, voltage – 32 V, air stream pressure – 0.6 MPa, spray distance – 120 mm. The surface topography revealed the plate structure of the coating with slats of different chemical composition. In coating are presence of carbides and borides, a significant amount of iron oxides and oxides of alloyed elements at the slats. Provisions from a considerable height contribute to intense wear due to reducing the friction steam surface. The interaction is regulated by the ratio of the depth of the projections (H) to the radius of its sharp tip (r). When H/r <0.02, there is only elastic interaction, with the material of counteraction elastic. In the range of 0.02 < H/r <0.7, the projections induce plastic deformation of the counter-body. If H/r > 0.7, sharp projections are cut to the surface, generating micro -cutting. Reducing the number and size of inclusions and increasing their rounding radii are critical for improving wear resistance etc. Робота присвячена дослідженню впливу компонентів складу порошкових дротів на поверхневі характеристики відшліфованих електродугових покриттів. Для нанесення покриттів застосовувався електродуговий розпилювач та порошкові дроти діаметром 1,8 мм, що містять порошки FеSі, FеTі, FеMn, чисті метали Al і Cr та карбід B4C з коефіцієнтом наповнення досяг 24%. Параметри розпилення: струм – 150 А, напруга – 32 В, тиск повітряного струменя – 0,6 МПа, відстань розпилення – 120 мм. Топографія поверхні виявила пластинчасту структуру покриття з ламелями різного хімічного складу і мікротвердості, наявність карбідів та боридів, значну кількість оксидів заліза та оксидів легованих елементів на межах ламелей. Виступи з значної висоти сприяють інтенсивному зносу через зменшення поверхні пари тертя тощо.Item Вплив матеріалу металевої основи на механічні характеристики електродугових покриттів(ЦНТУ, 2024) Гвоздецький, В. М.; Студент, М. М.; Задорожна, Х. Р.; Маркович, С. І.; Hvozdetskii, V.; Student, M.; Zadopozna, K.; Markovych, S.В роботі проведено дослідження впливу матеріалу металевої основи (алюмінієвого сплаву Д16 та сталі Ст 3) на механічні характеристики електродугових покриттів. Покриття з порошкового дроту наносились в режимах дозвукового (тиск 0,6 МПа) та надзвукового повітряного струменю (тиск 1,2 МПа). При цьому виявлено наявність дисперснішої структури, меншу кількість пор і мікротріщин. Для оцінки роботоздатності покриттів введено новий параметр, а саме – співвідношення між величинами залишкових напружень розтягу І роду та когезивної міцності – σкол/σв. Визначено, що утворення тріщин починається при значеннях цього показнику σкол/σв 0,75, тоді як за σкол/σв 0,85 у покриттях виникає мережа тріщин. Рівень напружень розтягу першого роду у покриттях напилених на алюмінієву основу є меншим ніж у покриттях напилених на сталь, що зумовлено більшим коефіцієнтом термічного розширення алюмінієвого сплаву ніж сталі. Aluminum alloys are characterized by low abrasive wear resistance, which significantly hinders their widespread use in technological environments, especially in the presence of abrasive particles. Recently, there has been a trend to replace steels with aluminum alloys with wear-resistant coatings. This makes it possible to reduce, firstly, the weight of parts, and secondly, carbon dioxide emissions into the atmosphere and the greenhouse effect. In the process of spraying wear-resistant coatings on a steel base, significant tensile stresses arise in the coating, which can lead to the appearance of micro and macro cracks in the coatings. There is no reliable data in the literature on the cohesive strength and level of stresses that are formed in powder wire coatings sprayed on a base of aluminum alloys, which hinders the development of a technology for restoring aluminum alloy parts by electric arc spraying.Item Залежність структури електродугових покриттів від параметрів напилення деталей транспортної техніки(ЦНТУ, 2023) Студент, М. М.; Маркович, С. І.; Задорожна, Х. Р.; Гвоздецький, В. М.; Student, М.; Markovych, S.; Zadopozna, K.; Hvozdetskii, V.Досліджено умови плавлення та структуру покриттів, напилених методом електродугового напилення залежно від тиску повітряного струменю. Показано, що збільшення тиску металоповітряного потоку від 0,6 до 1,2 МПа підвищує швидкість струменю від 300 до 600 м/с, при цьому дисперговані краплини досягають швидкості від 120 до 220 м/с. Відповідно це викликає зменшення товщини ламелей електродугового покриття, а також сприяє формуванню підвищеної кількості оксидної фази на поверхні ламелей. Це збільшує мікротвердість покриття із У8 із 350-400 HV за тиску 0,6 МПа. до 450...500 HV за тиску 1,2 МПа. Мікротвердість покриттів із 90Х17Р3ГС зростає від 600 до 740 HV. The use of special flux-cored wires for electric arc spraying allows for coatings with high wear resistance. However, the insufficient adhesion and cohesion of the resulting coatings does not allow these coatings to be used under increased operating loads. To improve the mechanical characteristics of gas-thermal coatings, a supersonic gas jet is used to transport molten droplets to the sprayed surface, increasing their kinetic energy. It is proposed to apply a supersonic air jet using a Laval nozzle and increasing the air jet pressure from 0.6 to 1.0...1.2 MPa. The aim of the study is to determine the effect of air jet pressure on the structure of electric arc coatings.Item Дослідження впливу температури електроліту при імпульсному анодуванні на властивості поверхневих шарів технічного алюмінію(ЦНТУ, 2023) Гвоздецький, В. М.; Маркович, С. І.; Задорожна, Х. Р.; Студент, М. М.; Hvozdetskii, V.; Markovych, S.; Zadorozhna, К.; Student, М.Імпульсне анодування формує оксидні шари на алюмінієвих сплавах, що дозволяє отримати поверхневі шари з високою твердістю (до 2000 HV), низьким коефіцієнтом тертя, високою адгезією до металевої основи та низькою екологічною небезпекою. Проведено дослідження впливу температури імпульсного анодування на структуру та зносостійкість анодованих шарів. Встановлено, шо більше молекул води та сірки в анодованому шарі, то менша його мікротвердість та абразивна зносостійкість. Мінімальний знос анодованого шару, а значить найвищу його зносостійкість, зафіксовано для шарів, синтезованих за температури анодування -8ºС, а максимальний знос та найменшу зносостійкість за температури анодування -5ºС. Висока зносостійкість анодованих шарів, синтезованих за температур електроліту від -8 до +10ºС за умов тертя без мащення зумовлена наявністю кристалічної води в анодованому шарі. luminum alloys are characterized by low abrasive wear resistance, which significantly restricts their wide use in technological environments, especially if they contain abrasive particles. The method of pulse anodizing, which consists in periodically changing the current density, allows to improve the hardness and abrasive wear resistance. However, the influence of temperature on these processes has not been sufficiently studied.Item Вплив складу шихти порошкових дротів на механічні властивості та корозійну стійкість електродугових покриттів(ЦНТУ, 2023) Студент, М. М.; Маркович, С. І.; Гвоздецький, В. М.; Задорожна, Х. Р.; Student, М.; Markovych, S.; Hvozdetskii, V.; Zadopozna, К.Досліджено механічні властивості, хімічну мікрогетерогенність та корозійну стійкість у 3% водному розчині NaCl електродугових покриттів з порошкових дротів (ПД) залежно від компонентного складу шихти, використаного під час їх виготовлення. Показано, що покриттям з ПД властива висока неоднорідність за хімічним складом, що відрізняє їх від покриттів, отриманих розпилюванням суцільних дротів. Адже подрібнені повітряним струменем краплини розплаву ПД, що формують покриття, суттєво різняться за хімічним складом. Такий градієнт спричинений неповним розплавленням і змішуванням складників шихти та сталевої оболонки в дузі між торцями ПД під час електродугового напилювання покриттів. Запропоновано додавати до складу шихти ПД порошки, які забезпечили би в краплинах розплаву ПД необхідну кількість хрому, бору, вуглецю. А саме, додавання до шихти ПД порошків ферохрому (ФХ), карбіду бору (B4C), ферохромбору (ФХБ), феросплавів (FeSi, FeMn) та самофлюсу ПГ10Н-01 дало змогу підвищити гомогенність розплаву ПД та активізувати утворення евтектик між складниками шихти ПД 90Х17РГС та ПД 90Х17Р3ГС. Завдяки цьому добились нижчої хімічної мікрогетерогенності отриманих покриттів та забезпечили їм високу корозійну тривкість, близьку до корозійної тривкості нержавіюча сталі Х18Н9Т. Electric arc spraying of coatings is common in many branches of industrial production, in particular to restore the geometry of machine parts worn in operational conditions, to increase their protection against abrasive and gas-abrasive wear (at the same time, both at climatic and at technologically determined elevated temperatures). Coatings sprayed using powdered wires are characterized by high chemical heterogeneity, which significantly distinguishes them from electric arc coatings made of solid wires. This is due to the different chemical composition of the droplets formed from the molten powder wires and carried by the air jet to the surface of the substrate, forming a coating on it. The charge with alloying elements in its composition (including difficult-to-melt ones such as FH, B4C, FHB) does not have time to fully melt and mix with the melt of the steel shell. It is clear that because of this, the melt droplets of flux-cored wires dispersed by an air jet will have a different chemical composition and , as a result, the coatings formed from these droplets on the surface of the substrate will be characterized by high heterogeneity and significant chemical heterogeneity, which will affect their physical and mechanical properties at different operating temperatures and especially when exposed to corrosive environments.Item Підвищення абразивної зносостійкості алюмінієвих ливарних сплавів Al-Si АК-9 та АК-12 плазмо-електролітною обробкою(ЦНТУ, 2022) Студент, М. М.; Погрелюк, І. М.; Маркович, С. І.; Гвоздецький, В. М.; Задорожна, Х. Р.; Топчій, В. І.; Student, M.; Pogrelyuk, I.; Markovych, S.; Hvozdetskii, V.; Zadopozna, K.; Topchiy, V.Досліджено структуру, мікротвердість та абразивну зносостійкість алюмінієвих ливарних сплавів Al-Si АК-9 та АК-12 силумінів. Фазовий аналіз показав, що оксидний ПЕО шар складається із двох оксидних фаз αAl2O3, γAl2O3 та силікатної фази Al2SiO3. Кремній є присутній у структурі оксидного шару проте його є менше ніж у структурі силумінів. Встановлено, що в процесі плазмо-електролітної обробки кремній розчиняється у лужному електроліті. Показано, що плазмоелектролітна обробка силумінів АК-9 та АК-12 підвищує їх мікротвердість до 1000 …1300 HV, це спричиняє підвищення їх абразивної зносостійкості у 14...57 разів. Додаток в електроліт перекису водню H2O2 у кількості 3% мас. підвищує абразивну зносостійкість силумінів після плазмоелектролітної обробки ще на 30...70%. Це зумовлено збільшенням оксидних фаз та зменшенням силікатної фази Al2SiO3 у структурі покриття. Aluminum casting alloys are used in machine-building, automobile, aviation, electrical and textile enterprises. However, aluminum alloys have low abrasive wear resistance, which significantly hinders their use in technological environments where abrasive particles are present. However, aluminum alloys have low abrasive wear resistance, which significantly hinders their use in technological environments where abrasive particles are present. The method of plasma electrolytic oxidation of plasma electrolyte treatment on aluminum alloys provides high hardness up to 2000 HV, low friction coefficient, high adhesion to the metal base, high environmental friendliness. However, this method does not allow the synthesis of oxide layers with high abrasive wear resistance on cast alloys - silumin. Plasma electrolyte treatment layers synthesized on the most widely used Al-Si foundry alloys have significant disadvantages: low rate of synthesis of the oxoceramic layer - 0.5 - 1 μm / min., Low thickness - up to 140 μm, low microhardness (700- 1000 HV) and low abrasion resistance. Plasma electrolyte treatment layers were synthesized on the surface of 30x30 mm plates with a thickness of 4 mm from aluminum casting alloys AK-9 (9% Si) and AK-12 (12% Si) in electrolyte - 3 g / l KOH + 2 g / l Na2SiO3 (aqueous solution of liquid glass) without and with the addition to the electrolyte of 3 g / l of hydrogen peroxide H2O2, pulsed current at a frequency of 50 Hz in the cathode-anode mode at a ratio of currents (Ik / Ia) = 1 and a current density of 20 A / dm2. The thickness of the coatings after synthesis for 120 min was 120 -130 μm .. [4]. Metallographic studies were performed on a scanning electron microscope ZEISS EVO 40XVP with X-ray microanalysis system INCA Energy. The phase composition of the surface layers was investigated using a DRON-3M diffractometer in Cu-K radiation. Conclusions: 1. Plasma-electrolyte treatment of silumins AK-9 and AK-12 increases their microhardness up to 1000… 1300 HV, which causes an increase in their abrasive wear resistance by 14 ... 57 times. 2. Addition to the electrolyte of hydrogen peroxide H2O2 in the amount of 3% of the mass. increases the abrasive wear resistance of silumins after plasma electrolyte treatment by another 30 ... 70%. This is due to the increase in the content of oxide phases αAl2O3, γAl2O3 and the decrease in the content of the silicate phase of sillimanite - Al2O3 · SiO2 in the coating structure.Item Зносостійкі покриття на алюмінієвих сплавах(ЦНТУ, 2022) Студент, М. М.; Маркович, С. І.; Гвоздецький, В. М.; Задорожна, Х. Р.; Сірак, Я. Я.; Кравчишин, Т. М.; Student, M.; Markovych, S.; Hvozdetskii, V.; Zadorozhna, K.; Sirak, Ya.; Кrаvchyshyn, T.Досліджено абразивну зносостійкість алюмінієвого сплаву Д16 з покриттями нанесеними методами: гальванічного хромування, надзвукового газополуменевого напилення (HVOF – High Velocity Oxygen Fuel Flame Spraying process), плазмо-електролітного оксидування, твердого анодування та електродугового напилення покриттів. Показано, що досліджені покриття підвищують абразивну зносостійкість алюмінієвого сплаву Д16 в 20...90 разів за умов випробовувань закріпленим абразивом та в 3...10 разів за умов випробовувань незакріпленим абразивом. Застосування цих методів підвищує зносостійкість деталей із алюмінієвих сплавів до рівня сталевих та дозволяє замінювати сталь і чавун на алюмінієві сплави із покриттями, щоб зменшити вагу деталей та викиди вуглецю в атмосферу. Aluminum alloys are widely used in industry. Recently, they are used as a replacement for steel for the manufacture of pulleys, gears, columns of hydraulic rotary transmissions of grabs, etc. This reduces the weight of the parts and reduces carbon emissions into the atmosphere. However, aluminum alloys have low abrasive wear resistance, so their use is possible with coatings on the surface. High-speed gas flame spraying (HVOF) was carried out on the equipment (Diamond Jet Hybrid gun). Arc coatings with a thickness of 500 µm were applied using FMI metallizer and FMI-2 powder wire (Cr6Al6B3Fe-base). PEO (oxido ceramic) coatings were synthesized on D16T aluminum alloy in an electrolyte of 3 g/l KOH + 2 g/l liquid glass (sodium silicate) with a pulsed current at a frequency of 50 Hz, with the ratio of the densities of the cathode and anode currents Jc/Ja+15/15 A /dm2. The duration of the PEO process is 60 min. The open porosity of the coatings was determined by the method of hydrostatic weighing. The phase composition of the surface layers was studied using a DRON-3.0 diffractometer. HVOF (VC) and PEO coatings have been found to have 3 to 4 times higher wear resistance than high carbon hardened steel 100Cr6 and 2 times higher than galvanic chromium coatings, but have high energy consumption. Two methods have the lowest energy consumption: electric arc spraying of coatings and hard anodizing. At the same time, the wear resistance of such coatings is significantly lower than that of coatings obtained by the PEO and HVOF (VC) methods. For the restoration of worn parts, the most appropriate methods are HVOF (VC) and electric arc spraying, as they allow applying thick coatings up to 5 mm. Conclusions: It was established that the studied HVOF (VC), PEO, EDP and hard anodized coatings significantly increase the abrasive wear resistance of aluminum alloy parts. HVOF (VC) and electric arc spraying methods can be used to protect new and worn parts from wear. PEO and hard anodizing methods can be used to protect against wear on new parts only. The use of these methods increases the wear resistance of parts made of aluminum alloys to the level of steel and allows replacing steel and cast iron with aluminum alloys with coatings, reducing the weight of parts and carbon emissions into the atmosphere.Item Зносостійкість оксидних шарів сформованих методом твердого анодування (hard anodic coatings) при зміцненні деталей агропромислової техніки(ЦНТУ, 2021) Студент, М. М.; Маркович, С. І.; Гвоздецький, В. М.; Задорожна, Х. Р.; Ковальчук, І. С.; Дзьоба, Ю. В.; Student, M.; Markovych, S.; Hvozdetskii, V.; Zadorozhna, K.; Kovalchuk, I.; Dzjoba, Yu.Синтез анодованого шару на сплаві алюмінію виконували у 20 % розчині сірчаної кислоти за температури -8…- оС. Під час анодування густина струму становила 5 A/дм2. Час анодування становив 60, 120 та 180 хв. Проводили металографічні дослідження та фазовий аналіз анодованих шарів. Зменшення вмісту вологи проводили за температури 400 оС впродовж 60 хв. Встановлено, що оксидний шар (Al2O3H2O) під час твердого анодування на алюмінієвих сплавах формують не лише йони кисню, які утворюються внаслідок розкладу води, а також його нейтральні атоми, які формуються з розчину. Виявлено, із збільшенням часу анодування зростає мікротвердість та товщина шару. Після термічної обробки кількість молекул води зменшується і мікротвердість зростає. Підвищення мікротвердості сприяє зростанню опору абразивному зношуванню. In the last years in an agroindustrial production there is a tendency on replacement of cast-iron details on a detail from aluminium alloys at execution on поверхю of strengthening layer. An ironmaking is accompanied the extrass of plenty of carbon dioxide in an atmosphere. Substituting of cast-iron details by aluminium will decrease the amount of extrass of carbon dioxide in an atmosphere, and substantially will decrease weight of constructions. Hard anodization is used practically in all of industries of industry: avsup and motor-car industry; hydraulics; electronics; heater platforms and tiles; medical devices. This method will allow to promote mechanical descriptions of aluminium alloys the method of forming of the anodized layers on their surface. The synthesis of the anodized layer on an aluminum alloy was performed in a 20% solution of sulfuric acid at a temperature of (-8…-2 °C). During anodizing, the current density was 5 A / dm2. The anodizing times were 60, 120 and 180 minutes. Conducted metallographic studies and phase analysis of the layers. Reduction of moisture content was performed at a temperature of 400°C for 60 minutes. It was found that the oxide layer (Al2O3 · H2O) during hard anodizing on aluminum alloys forms not only oxygen ions, which are formed due to the decomposition of water, but also its neutral atoms, which are formed from the solution. It was found that the microhardness and layer thickness increase with increasing anodizing time. After heat treatment, the number of water molecules decreases and the microhardness increases. Increasing the microhardness increases the resistance to abrasive wear. Conclusions: The layer of oxide in the composition contains to three molecules of water, which reduce a microhardness, and and wearproofness of the anodized layer substantially. The layers of oxide on aluminium alloys are formed the method of cold anodization at low temperatures -8…-4 °C to 6 time promote abrasive wearproofness of aluminium alloy of D16. Heat treatment for the temperatures of 400°C during 2 hours promotes abrasive wearproofness of aluminium alloy on an order.Item Вплив складу електроліту на характеристики синтезованого під час твердого анодування алюмінію оксидного шару(ЦНТУ, 2021) Студент, М. М.; Гвоздецький, В. М.; Веселівська, Г. Г.; Задорожна, Х. Р.; Мардаревич, Р. С.; Сірак, Я. Я.; Маркович, С. І.; Student, M.; Hvozdetskii, V.; Veselivska, H.; Zadorozhna, K.; Mardarevych, R.; Sirak, Ya.; Markovych, S.Тверде анодування виконано за температури –4...0 °С впродовж 60 хв. Як базовий електроліт використано 20%-й водний розчин H2SO4. Під час анодування густина струму становила 5 A/дм2. Щоб з’ясувати вплив сильних окиснювачів на характе¬ристики анодних шарів (оксидних), в електроліт додавали 30; 50; 70 та 100 г/л перекису водню (H2O2). В деяких випадках його продували озоно-повітряною сумішшю з розрахунку 5 мгхв/л озону. Встановлено, що оксидний шар (Al2O3H2O) під час твердого анодування на алюмінієвих сплавах формують не лише іони кисню, які утворюються внаслідок розкладу води, а також його нейтральні атоми, які форму¬ються через розкладання перекису водню та озону. Виявлено, що перекис водню, а також продування електроліту збільшують товщину та мікротвердість анодного шару на 50% внаслідок зниження вдвічі кількості молекул води в оксиді алюмінію. Перекис водню та озон, очевидно, зменшують і товщину бар’єрного шару покриття, крізь який проникають іони кисню та алюмінію, які, з’єднуючись, формують оксидний шар. The aim of the study. By introducing strong oxidizers to the electrolyte form anode layers on the surface of aluminum with increased mechanical characteristics. To determine the effect of the duration of the formation of an anode layer to change its properties. Hard anodizing was performed at a temperature of –4...0°C for 60 min. A 20% aqueous solution of H2SO4 was used as the base electrolyte. During anodizing, the current density was 5 A/dm2. To determine the effect of strong oxidants on the characteristics of the anode layers (oxide), 30 were added to the electrolyte; 50; 70 and 100 г/лof hydrogen peroxide (H2O2). In some cases, it was purged with an ozone-air mixture at a rate of 5 mgmin/l of ozone. It was found that the oxide layer (Al2O3H2O) during hard anodizing on aluminium alloys forms not only oxygen ions, which are formed by the decomposition of water, but also neutral oxygen atoms, which are formed by the decomposition of hydrogen peroxide and ozone. It was found that hydrogen peroxide, as well as blowing the electrolyte with an air-ozone mixture increase the thickness and microhardness of the anodized layer by 50% due to the reduction of the number of water molecules in alumina by half. Hydrogen peroxide and ozone apparently also reduce the thickness of the barrier layer of the coating, through which oxygen and aluminium ions penetrate and which, when combined, form an oxide layer. Conclusions. 1. It has been established that aluminum anodizing for 60 minutes. provides an increase in its properties. Changing the composition of the electrolyte contributes to the growth of microhardness in 1.2 ... 1.7 times. The resistance of abrasive wear increases with the content of different amounts of applications in the electrolyte and the maximum is at 30 g / l H2O2. Blowing the base electrolyte ozone provides an increase in the microhardness of the layer from 380 to 510 HV. The higher loss of mass for higher microhardness is caused by an increase in porosity of coatings. 2. It is determined that an increase in the anodization time in the baseline electrolyte to 120 and 180 minutes contributes to the growth of microhardness to 640 HV compared to an anodized layer for 60 minutes. Loss of mass in the study of abrasive wear is less than 3-4 times with longer anodation than at 60 minutes in the baseline electrolyte.Item Вплив складу шихтових матеріалів порошкових дротів на механічні характеристики та корозійну стійкість електродугових покриттів(ЦНТУ, 2020) Студент, М. М.; Головчук, М. Я.; Гвоздецький, В. М.; Веселівська, Г. Г.; Маркович, С. І.; Яцюк, Р. А.; Student, M.; Golovchuk, M.; Hvozdetskii, V.; Veselivska, H.; Markovych, S.; Yatsyuk, R.Встановлено вплив шихтових матеріалів порошкових дротів на їх механічні характеристики, хімічну мікрогетерогенність та корозійну стійкість у середовищі водного розчину 3%NaCl. Показано, що на відміну від покриттів із суцільних дротів покриття, напилені із використанням порошкових дротів (ПД), мають високу хімічну гетерогенність. Це зумовлено тим, що краплини, які диспергуються із розплаву ПД та формують покриття мають неоднаковий хімічний склад. Спричинено це неповним сплавленням шихти та сталевої оболонки на торцях ПД під час електродугового напилення покриттів. Для зменшення хімічної мікро гетерогенності запропоновано у шихту порошкового дроту що містить хром, бор, вуглець місткі компоненти (Cr, ФХ, ПГ-100, B4C, ФХБ) додавати порошки феросплавів FeSi, FeMn та самофлюсу ПГ-10Н-01, які сприяють утворенню евтектик між складниками шихти, гомогенізують розплав ПД та, як наслідок, зменшують мікрогетерогенність покриттів. Наявність у шихті ПД 90Х17РГС та ПД 75Х19Р3ГС2 хрому, ферохрому, ферокремнію та феромарганцю зумовлює мінімальну хімічну мікрогетерогенність покриттів з цих дротів і, як наслідок забезпечує їх високу корозійну тривкість, що наближається до корозійної тривкості наржавної сталі Х18Н9Т. The influence of charge materials of flux-cored wires on their mechanical characteristics, chemical microheterogeneity and corrosion resistance in an aqueous solution of 3% NaCl was established. It is shown that, in contrast to coatings made of solid wires, coatings sprayed using flux-cored wires (PO) have a high chemical heterogeneity. This is due to the fact that the droplets that disperse from the PD melt and form a coating have different chemical compositions. This is caused by incomplete fusion of the charge and steel shell at the ends of the PD during electric arc spraying of coatings. To reduce the chemical micro-heterogeneity, it is proposed to add powders of ferroalloys FeSi, FeMn and self-flux PG-10H-01 to the charge of powder wire containing chromium, boron, carbon-containing components (Cr, FH, PG-100, B4C, FCB) between the components of the charge, homogenize the melt of PD and, as a consequence, reduce the microheterogeneity of the coatings. The presence of chromium, ferrochrome, ferro-silicon and ferromanganese in the charge of PD 90Х17РГС and PD 75Х19Р3ГС2 determines the minimum chemical microheterogeneity of coatings from these wires and, as a result, ensures their high corrosion resistance, which is close to corrosion steel18. To increase the completeness of fusion of the components of the PD charge between itself and its steel shell, it is proposed to add to the PD charge powders of ferroalloys Fe-Mn, Fe-Si, which have a low melting point, able to interact with refractory components of the charge to form low-temperature eutectics. The addition of ferro-silicon, ferromanganese and self-flux alloy PN-10H-01 powders based on ferrochrobor and ferrochrome provided high hardness of electric arc coatings, low heterogeneity in terms of chromium content in coating lamellae and, as a consequence, high corrosion resistance. Установлено влияние шихтовых материалов порошковых проволок на их механические характеристики, химическую микрогетерогенность и коррозионную стойкость в среде водного раствора 3% NaCl. Показано, что в отличие от покрытий из сплошных проводов покрытия, напыленные с использованием порошковых проволок (ПД), имеют высокую химическую гетерогенность. Это обусловлено тем, что капли, которые диспергируются с расплава ПД и формируют покрытия имеют неодинаковый химический состав. Причины этого вызваны неполным сплавлением шихты и стальной оболочки на торцах ПД при электродуговом напылении покрытий. Для уменьшения химической микрогетерогенности предложено в шихту порошковой проволоки содержащей хром, бор, углерод вместительные компоненты (Cr, ФХ, ПГ-100, B4C, ФХБ) добавлять порошки ферросплавов FeSi, FeMn и самофлюса ПГ-10Н-01, которые способствуют образованию эвтектик между составляющими шихты, гомогенизируют расплав ПД и, как следствие, уменьшают микрогетерогенность покрытий. Наличие в шихте ПД 90Х17РГС и ПД 75Х19Р3ГС2 хрома, феррохрома, ферокремния и ферромарганца приводит к минимальной химической микрогетерогенности покрытий из этих проволок и, как следствие обеспечивает их высокую коррозионную стойкость, которая приближается к коррозионной стойкости наржавеющей стали Х18Н9Т.