Збірники наукових праць ЦНТУ
Permanent URI for this communityhttps://dspace.kntu.kr.ua/handle/123456789/1
Browse
Search Results
Item Підвищення ефективності використання транспортних машин у агропромисловому виробництві узгодженням їх експлуатаційних характеристик та умов функціонування(ЦНТУ, 2022) Аулін, В. В.; Гриньків, А. В.; Лисенко, С. В.; Голуб, Д. В.; Лівіцький, О. М.; Aulin, V.; Hrinkiv, А.; Lysenko, S.; Holub, D.; Livitskyi, O.В даній роботі розглянуто питання підвищення ефективності використання транспортних машин у агропромисловому виробництві узгодженням їх експлуатаційних характеристик та умов функціонування. Запропоновано підхід узгодження експлуатаційних характеристик машин з умовами функціонування, який базується на структурній та імітаційних моделях системи "транспортна машина- умови її функціонування". Пропонується ітераційне рішення імітаційної моделі з пошуком оптимальних параметрів. В якості інтегрального критерію ефективності використання транспортної машини на підприємстві агропромислового виробництва взято питому витрату палива на здійснення транспортної роботи. Специфічність умов експлуатації транспортних машин запропоновано характеризувати коефіцієнтом узгодженості, який відображає вплив умов функціонування на питому витрату палив при транспортних роботах. Узгодження характеристик транспортних машин з умовами функціонування, обґрунтування їх оптимальних конструкційних параметрів, проводили підбором параметрів трансмісії, що забезпечують покращення умов частковим демпфіруванням коливань навантаження. Представлені результати параметрів демпфіруючого вузла трансмісії автомобіля КамАЗ-4308 для різних режимів руху. Для цих умов проведені базові, теоретичні, експериментальні оцінки коефіцієнта узгодженості, а також дано рекомендовані режими руху транспортних машин при вивезенні зернових від комбайна для автомобілів КамАЗ-4308 та тракторних агрегатів МТЗ-82+2ПТС4. This paper examines the issue of increasing the efficiency of the use of transport vehicles in agroindustrial production by harmonizing their operational characteristics and operating conditions. The approach of matching the operational characteristics of machines with the conditions of operation is proposed, which is based on structural and simulation models of the "transport machine-conditions of its operation" system. An iterative solution of the simulation model with the search for optimal parameters is proposed. The specific fuel consumption for carrying out transport work is taken as an integral criterion for the efficiency of the use of a transport vehicle at an agro-industrial production enterprise. The specificity of the operating conditions of transport vehicles is proposed to be characterized by the consistency coefficient, which reflects the influence of operating conditions on the specific fuel consumption during transport operations. This coefficient takes into account the influence of the characteristics of the engine, cargo and external load. the corresponding system of equations is given as a mathematical model, which was supplemented with auxiliary dependencies that determine the boundary conditions of the operation of individual subsystems of transport machines, their control conditions and transitions of the model from a dynamic state based on a simulation model, the characteristics of machines and their structural elements in time are calculated for cases of partial high-speed and loading modes and transitions between them. Matching the characteristics of transport vehicles with the operating conditions, justifying their optimal design parameters, was carried out by selecting the transmission parameters, which ensure the improvement of conditions by partial damping of load fluctuations. The results of the parameters of the damping assembly of the transmission of the KamAZ-4308 car for different driving modes are presented. For these conditions, basic, theoretical, and experimental evaluations of the consistency coefficient were carried out, as well as recommended driving modes of transport vehicles when removing grain from the КамАЗ-4308 combine for cars and МТЗ-82+2ПТС4 tractor units.Item Використання методів теорії сенситивів при розв'язанні завдань технічних, транспортних і виробничих систем і процесів(ЦНТУ, 2022) Аулін, В. В.; Aulin, V.На прикладі функції технічного стану систем і агрегатів машин як функції діагностичних параметрів побудовано критерій її відносної чутливості (сенситив). Розглянуто відносний критерій чутливості (сенситив) і для кожного діагностичного параметру і функції стану від вагомих факторів та від напрацювання. Використовуючи властивості сенситивів та методику реалізації теорії чутливості функцій, отримано частинні критерії відносної чутливості. Розглядаючи сукупність функцій діагностичних параметрів і функції надійності, як функції ймовірності безвідмовної роботи від напрацювання, показано, що вони параметрично задані. Встановлено зав'язок сенситивів діагностичних параметрів з рівнем надійності систем, агрегатів і машин в цілому. Розроблено блок-схему методу визначення характеру динамічного розвитку діагностичних параметрів та показників надійності технічного стану систем і агрегатів машин. На основі даних експериментальних досліджень побудовано математичні моделі відносної чутливості (сенситиву) для найбільш інформативно значущих діагностичних параметрів силових агрегатів та трансмісій. Показано, що математичні моделі сенситивів діагностичних параметрів дають можливість визначити локальні значення сенситиву на діапазонах напрацювання і є ефективним інструментом для відбору діапазонів напрацювання, на яких варто контролювати певні діагностичні параметри щоб забезпечити належний рівень надійності систем, агрегатів та машини в цілому. The criterion of its relative sensitivity (sensitivity) is constructed on the example of the function of technical condition of systems and units of machines as a function of diagnostic parameters. The relative criterion of sensitivity (sensitivity) for each diagnostic parameter and function of the state of weighting factors and operating time is considered. Using the properties of sensitivities and the method of realization of the theory of sensitivity of functions, partial criteria of relative sensitivity are obtained. Considering the set of functions of diagnostic parameters and reliability functions as functions of probability of trouble-free operation, it is shown that they are parametrically set. The connection of sensitivities of diagnostic parameters with the level of reliability of systems, units and machines in general is established. The block diagram of a method of definition of character of dynamic development of diagnostic parameters and indicators of reliability of a technical condition of systems and units of cars is developed. Mathematical models of relative sensitivity (sensitivity) for the most informatively significant diagnostic parameters of power units and transmissions are built on the basis of experimental research data. It is shown that mathematical models of sensitivity of diagnostic parameters allow to determine local values of sensitivity on operating ranges and are an effective tool for selection of operating ranges on which certain diagnostic parameters should be controlled to ensure proper reliability of systems, units and machines as a whole.