Збірники наукових праць ЦНТУ
Permanent URI for this communityhttps://dspace.kntu.kr.ua/handle/123456789/1
Browse
2 results
Search Results
Item Щодо надійності технологічного процесу подрібнення пожнивних решток(ЦНТУ, 2023) Сало, В. М.; Богатирьов, Д. В.; Лещенко, С. М.; Salo, V.; Bohatyrov, D.; Leshchenko, S.Робота присвячена пошукам шляхів вирішення проблеми підвищення надійності технологічного процесу подрібнення пожнивних решток із використанням котків-подрібнювачів, робочі органи яких, виготовлені у вигляді ножових барабанів. Представлений огляд та аналіз існуючих типів машин для подрібнення пожнивних решток, обладнаних приводними та безприводними активними робочими органами, відмічені їх переваги та недоліки. Сформульовані шляхи та способи, на які варто звернути увагу при вирішенні задач підвищення якості подрібнення та надійності протікання даного технологічного процесу. Представлений зміст та методи проведення експериментальних польових досліджень процесу подрібнення пожнивних решток барабаном з ножами, встановленими на його поверхні під певним кутом розхилу між сусідніми рядами та зі зміщенням лінії лез рядів відносно осі самого барабана. Доведено, що при певних значеннях вказаних параметрів можна досягти значного підвищення надійності технологічного процесу, практично позбутися негативного явища забивання міжножового простору частинками рослинних стебел та ґрунтом. The article is devoted to finding ways to solve the problem of increasing the reliability of the technological process of shredding crop residues using shredding rollers with operating parts in the form of knife drums. The research presents a review and analysis of existing types of machines for shredding crop residues equipped with driven and non-driven active operating parts with their advantages and disadvantages. The ways and methods that should be considered when solving problems of improving the quality of grinding and reliability of this technological process are formulated. The article presents the content and methods of conducting experimental field studies of the process of shredding crop residues by a drum with knives installed on its surface at a certain angle of deflection between adjacent rows and with a shift of the line of row blades relative to the axis of the drum itself. It is proved that at certain values of these parameters, it is possible to achieve a significant increase in the reliability of the technological process, to virtually eliminate the negative phenomenon of clogging of the inter-row space with particles of plant stems and soil. The rational values of the angles of the knives on the surface of the chopping drum, substantiated in this work, allow increasing the intensity of chopping crop residues as a result of reducing the distance between the rows of knives. Thus, the approximate length of the particles of chopped plant stems can be reduced from 21.4 cm to 17.4 cm, without negative consequences for the reliability of the technological process.Item Вплив параметрів барабана для подрібнення рослинних решток на надійність протікання технологічного процесу(ЦНТУ, 2021) Сало, В. М.; Лещенко, С. М.; Богатирьов, Д. В.; Salo, V.; Leshchenko, S.; Bohatyrov, D.В роботі проводиться оцінка параметрів барабана для подрібнення рослинних решток на надійність протікання технологічного процесу. Проаналізовано існуючі конструкції котків- подрібнювачів рослинних решток та обґрунтовано взаємозв’язок окремих конструктивних та технологічних параметрів подрібнювачів на якісні показники їх роботи і можливість забивання міжножового простору. Проведені експериментальні дослідження по оцінці впливу кута розхилу між сусідніми ножами та робочої швидкості агрегату на ймовірність забивання міжножового простору. Доведено, що підвищення швидкості руху подрібнювачів та збільшення кута розхилу між ножами сприяють зменшенню забивання міжножового простору рослинно-ґрунтовою масою навіть при підвищеній вологості. The paper presents the assessment of the parameters of a chopping rotor for shredding plant residues for the reliability of the technological process. The general objective of the work is to substantiate the design and experimental identification of rational parameters of crimp-rollers of plant residues based on the condition of preventing clogging of the inter-knife space with plant-soil mass. The existing designs of crimp-rollers of plant residues are analyzed and the interrelation of certain constructive and technological parameters of shredders on qualitative indicators of their operation and possibility of clogging of inter-knife space is substantiated. The design of a large diameter crimp-roller provides simultaneous full contact with soil of two and sometimes three knives, which during the operation of the roller, together with cutting stems, provides them clamping with soil particles between adjacent knives. The probability of clogging between knives with plant and soil mass increases sharply with the humidity level of the material. Experimental studies have been conducted to assess the effect of the angle of inclination between adjacent knives and the operating velocity of the unit on the probability of clogging the inter-knife space. It is proved that increasing the speed of the shredders and increasing the decay angle between the knives help to reduce clogging of the inter-knife space with plant-soil mass, even at high humidity. The introduction of technological processes of effective preparation of plant residues in the production of crop products will allow starting the system of soil conservation at a farm. It is most expedient to grind plant residues with driveless roller shredders, the main operating parts of which are rollers with knives mounted on the cylinder, and depending on the purpose, quantity and type of plant residues, rollers with large and small diameters are practically used. When shredding high-stem plant residues, it is recommended to use crimp-rollers of large diameter with the following parameters: speed of the unit is 7…8 m/s, the decay angle between adjacent knives is 42… 46º. These parameters of the crimp-roller of plant residues reduce the probability of clogging the inter-knife space to 8%.