Збірники наукових праць ЦНТУ
Permanent URI for this communityhttps://dspace.kntu.kr.ua/handle/123456789/1
Browse
4 results
Search Results
Item Електродугове фрезерування(КНТУ, 2015) Боков, В. М.; Bokov, ViktorЗапропоновано та досліджено спосіб електродугового фрезерування, зокрема пазів. Обґрунтовано технологічну схему формоутворення. Отримано математичні моделі технологічних характеристик, які дозволяють керувати процесом та прогнозувати його. The objective of the work is reasoning of technological pattern for shaping grooves by electric arc and prognostication for technological properties of electric-arc milling. The work shows the results of electric-arc groove milling research: - analysis and research of different technological patterns of shaping grooves; - designing of graphite electrode tool of composite structure which ensures working liquid pumping through a narrow parallel-plate duct; - mathematical modeling of technological properties of electric-arc milling. Conclusions. There has been offered a method of cavity working, grooves in particular, by electric-arc milling. There was given experimental reasoning for technological pattern of groove shaping by electric arc with use of graphite electrode tool of composite structure. There have been received mathematical models of technological properties of groove electric-arc milling which enable to control and forecast them.Item Обробка дугою отворів з використанням мідного електрода-інструмента(КНТУ, 2014) Боков, В. М.; Bokov, ViktorРозроблено основи прогнозування технологічних характеристик процесу обробки електричною дугою отворів мідними електродами-інструментами. Запропоновано та випробувано новий ефективний спосіб обробки малих отворів. The objective of the work is to forecast technological parameters and increase of efficiency of the process of dimensional treatment of holes by the arc using copper electrochemical machining electrodes. The work presents the results of experimental research of the following technological parameters: relative linear wear of a copper electrochemical machining electrode, roughness of the treated surface, flank spark gap, treatment productivity, specific output of treatment and unit discharge of energy. Conclusions: - theoretical and practical principles of forecasting technological parameters and increase of efficiency of the process of treatment of holes by the arc using copper electrochemical machining electrodes were worked out; - the simulator of relative linear wear of copper electrochemical machining electrode was received which enabled showing the conditions to minimize wear; - new effective way of treatment of small holes by the arc was suggested and tested.Item Моделювання показників міцності механічного компенсатора похибок системи «прес-штамп» із застосуванням метода скінченних елементів(КНТУ, 2014) Мірзак, В. Я.; Боков, В. М.; Mirzak, Vladimir; Bokov, ViktorРозроблено теоретичні та практичні основи прогнозування показників міцності механічного компенсатора похибок системи «прес-штамп» із застосуванням метода скінченних елементів. Отримані математичні моделі даних показників та на їх основі запропоновано і створено новий компенсатор, що здатний витримати номінальне зусилля преса. The objective of the work is to forecast the strength indicators and creation of a new compensator of defects of the system “press-punch” which can withstand nominal pressing force. The work has the results of: - systematic analysis of the elements of the structure of mechanic compensators; - modeling the indicators of strength of mechanic compensator with spherical concave sleeve bearing using the method of final elements; - modeling deformation pattern of the compensator under load. Conclusion: - theoretical and practical grounds for the forecasting the indicators of strength of mechanic compensator of defects in the system “press-punch” were worked out; - a new mechanic compensator with optimal geometric parameters which is able to withstand the nominal pressing force was created and suggested. This compensator is used to increase quality of separating thin sheet-metal stamping.Item Засоби динамічного моніторингу якості тонколистового розділового штампування в системі «прес-штамп»(КНТУ, 2015) Мірзак, В. Я.; Боков, В. М.; Mirzak, Vladimir; Bokov, ViktorСтаття присвячена засобам динамічного моніторингу якості тонколистового розділового штампування в системі «прес-штамп». Наведено технічні характеристики пристрою контролю точності для пресів номінальним зусиллям 0,4...0,63 МН, його схему, опис роботи й методику розрахунку основних параметрів. Запропоновано пристрій для динамічного моніторингу деформаційного стану штампа в процесі виконання технологічної операції. The aim of the work is the development of facilities of the dynamic monitoring of quality of thin-sheet dividing stamp in the system “press-stamp”. The analysis of the existent control of precision of press equipment and stamps was carried out. The recommendations on application of the appliances of dynamic monitoring of the deformation state of press onloading in the conditions of press-construction plants and devices for dynamic monitoring of the deformation state of stamp in the process of implementation of technological operation were made. Measuring complexes for the control of precision of press equipment on-loading with possibility of application of gamma–presses and monitoring of the deformation state of stamp in the process of technological loading were worked out. Application of the complexes increases the precision and quality of the production of press equipment as well as technological processes of parts stamping of high precision.