Збірники наукових праць ЦНТУ
Permanent URI for this communityhttps://dspace.kntu.kr.ua/handle/123456789/1
Browse
2 results
Search Results
Item Експериментальне дослідження деформації пружно-гвинтового хона(ЦНТУ, 2022) Щербина, К. К.; Підгаєцький, М. М.; Мажара, В. А.; Гречка, А. І.; Дяченко, Т. В.; Shcherbyna, K.; Pidhaietskyii, M.; Mazhara, V.; Hrechka, A.; Dyachenko, T.В статі описується процес регулювання радіального розміру пружно-гвинтового хона, який відбувається на підставі пружних деформацій замкненого гвинтового тіла. Розглядаються математичні моделі процесу деформації пружно-гвинтового хону в осьовому напрямку при статичних навантаженнях в умовах додаткового опору пружнім деформаціям. В результаті експериментального дослідження пружно-гвинтового хона визначена теоретична та експериментальна залежність величини приросту діаметра та сили деформації від осьової пружної деформації. Також представлені математичні моделі отримані в результаті проведеного експериментального дослідження залежності приросту діаметра від величини прикладеної сили та осьового пружного переміщення. One of the important issues in the development of agricultural engineering is to increase the efficiency of finishing processes of machining the surfaces of controlling parts of the hydraulic machines equipment and the fuel system of internal combustion engines. High accuracy and quality of parts influence the performance of functional indicators and the consistency of their performance. One of the processes of finishing machining is honing of precision holes. The factor that impacts the accuracy and quality of the machined hole is the ability to influence the process of formation of macrogeometry and microgeometry due to the flexibility of the process. The quality of the micro-relief is influenced by the kinematics of the formation of a grid of traces. The formation of macrogeometry, in turn, is influenced by the principle of formation of geometric production lines, taking into account copying of existing deviations and the transfer of wear of diamond-abrasive bars. To level the impact of existing deviations of the machined hole it is necessary to carry out a flexible control of the process of adjusting the radial size. To ensure the flexibility of the process of honing holes, a helix honing tool is proposed, which eliminates the shortcomings of the existing diamond-abrasive tool by using elastic deformations to increase the radial size and placement of diamond-abrasive bars at an angle of 45º. To study the process of adjusting the radial size of the helix honing tool, the calculated scheme of elastic deformation of the geometric axis and a mathematical model describing the deformation process are presented. An experimental setup of the deformation of the helix honing tool in the axial direction is also given. As a result of the experimental study of the helix honing tool, the theoretical and experimental dependence of the magnitude of the increase in diameter and the force of deformation on the axial elastic deformation is determined. There are also mathematical models obtained as a result of the experimental study of the dependence of the diameter increase on the magnitude of the applied force and axial elastic displacement.Item Динамічний аналіз традиційної кінцевої ланки хонінгувальної головки(ЦНТУ, 2019) Підгаєцький, М. М.; Щербина, К. К.; Мажара, В. А.; Дяченко, Т. В.; Подгаецкий, М. М.; Pidhaietskyii, M.; Shcherbyna, K.; Mazhara, V.; Dyachenko, T.В статі розглядається динамічний аналіз роботи традиційної кінцевої ланки системи регулювання радіального розміру хонінгувальної головки. Обґрунтовано доцільність проведення дослідження кінцевої ланки традиційної хонінгувальної головки у вигляді клинової кінематичної пари в зоні малих переміщень. Визначені математичні моделі передавальних функції клинової кінематичної пари в статиці та динаміці з врахуванням функціонування в зоні малих переміщень. З врахування отриманих математичних моделей побудована перехідна характеристика функціонування клинової кінематичної пари в динаміці, що вказує на наявність інерційності процесу регулювання радіального розміру. В статье рассматривается динамический анализ работы традиционной конечного звена системы регулирования радиального размера хонинговальные головки. Обоснована целесообразность проведения исследования конечного звена традиционной хонинговальные головки в виде клиновой кинематической пары в зоне малых перемещений. Определены математические модели передаточных функции клиновой кинематической пары в статике и динамике с учетом функционирования в зоне малых перемещений. С учета полученных математических моделей построена переходная характеристика функционирования клиновой кинематической пары в динамике, что указывает на наличие инерционности процесса регулирования радиального размера. The purpose of the article is to study the operation of the tail end of the traditional honing head in the conditions of transient mode in the zone of small motions. The expediency of the study is related to the unstable operation of the tail end in the form of a wedge kinematic pair under the conditions of transition, taking into account the action of friction forces. At low velocities of slip of the tail ends of the wedge kinematic pair (below the critical value) there is a sharply defined uneven motion, which has a stick-slip nature with periodic jumps and stops. The analysis of the operation of the traditional tail end in the form of a wedge kinematic pair in statics with obtaining mathematical models of transfer functions taking into account the action of friction forces was carried out. In order to identify the influence of friction forces in the zone of small motions at low sliding speeds, the analysis was made in the dynamics in the zone of transition. Dynamic analysis was performed on the basis of the theory of automatic control with the construction of the required dynamic characteristics. On the basis of the performed dynamic analysis, mathematical models of the transfer function of the wedge kinematic pair in the dynamics were obtained taking into account the action of kinetic forces of friction. Based on the obtained models, a transient characteristic of the process of the wedge kinematic pair was constructed, as well as logarithmically amplitude-frequency characteristics and logarithmic phase-frequency characteristics were constructed. The transition function of a wedge kinematic pair does not reach its constant value immediately, but according to the aperiodic law. Thus, the tail end reflects the inertia of the process under study and is therefore sometimes called inertial, which leads to the formation of a stick-slip motion, which impairs its accuracy of radial size regulation. The reason is the presence of static and kinetic friction with nonlinear characteristic in the zone of small motions.