Збірники наукових праць ЦНТУ
Permanent URI for this communityhttps://dspace.kntu.kr.ua/handle/123456789/1
Browse
2 results
Search Results
Item Теоретичне дослідження конусного стабілізатора потоку сипкого матеріалу установки безперервної дії для завантаження сипких матеріалів(КНТУ, 2016) Оришака, О. В.; Гуцул, В. І.; Артюхов, А. М.; Oryshaka, О.; Gutsul, V.; Artiuhov, А.Отримані залежності швидкості руху сипкого матеріалу по конусному стабілізатору залежно від величини кута конуса, відстані від конусного стабілізатора до заслінки клапана і коефіцієнта тертя сипкого матеріалу, зазору між торцем матеріалопровода і конусним стабілізатором, товщини шару сипкого матеріалу, що сходить з поверхні конуса. The resulting dependence of the speed of the free-flowing material in the feed device from the height of the free flight, the coefficient of friction, angle of inclination of the side walls of the receiving receiving hopper, as for the case of fixed position receiving hopper, and for the case of circular motion of the funnel for different values of the angular velocity. When you increase the angle of the surface of the cone to the horizontal and V0 the speed of descent of granular material from the cone increases, and the thickness of the layer of bulk material flow that is coming off the cone decreases. A significant impact on the speed of descent of granular material from the cone and the thickness of the layer of bulk material flow that is coming off the cone f has. For large values of the coefficient of friction of the granular material on the surface of the cone, the surface of the cone to cover the materials with small values of the coefficient of friction.Item Обгрунтування постачального пристрою установки безперервної дії для завантаження сипких матеріалів(КНТУ, 2014) Оришака, О. В.; Гуцул, В. І.; Артюхов, А. М.; Oryhsaka, O.; Gutsul, V.; Artiukhov, А.Визначений вплив параметрів постачального пристрою на швидкість руху сипкого матеріалу в каналах патрубків в стаціонарному положенні і при обертанні пристрою, зміна лінійної питомої маси сипкого матеріалу в патрубках, а також центр мас сипкого матеріалу. Установлено, що швидкість руху сипкого матеріалу в каналах патрубків при обертанні пристрою збільшується відносно його стаціонарного положення, що виключає порушення технологічного процесу із-за забивання каналів патрубків. Modern machines for loading friable materials into valve bags require a considerable amount of energy, allow the loss of fasoo material, as well as the violation of technological process at boot friable materials, so the improvement of modern mechanization is an actual scientific problem. The effect of the parameters of the feeding device the speed of movement of the friable material in the channels of the nozzle in a stationary position during rotation of the device, the change of a specific linear mass of granular material in the channel setup. It is established that the speed of the friable material in the channels of the nozzles during rotation of the device increases relative to its stationary position, which eliminates the violation of technological process of plugging nozzles. Resume: 1. The speed of movement of the friable material in patrols postchallenge of the device increases when the rotation of the rotor relative to the stationary position of the rotor. This makes it possible to avoid the accumulation of loose material that could lead to blockage of the channel. 2. With increasing angular velocity of rotation of the rotor the flow of material moves from the lower to the upper wall of the socket. 3. The weight of friable material in patrols, when the rotor is reduced.