Збірники наукових праць ЦНТУ
Permanent URI for this communityhttps://dspace.kntu.kr.ua/handle/123456789/1
Browse
7 results
Search Results
Item Розробка цифрового інтерфейсу для керування імпульсним блоком живлення(ЦНТУ, 2024) Баранюк, О. Ф.; Каліч, В. М.; Baraniuk, O.; Kalich, V.Викладено результати розробки цифрового інтерфейсу до імпульсних блоків живлення з аналоговим контуром керування. Показано, що регулювання напруги блоку живлення можна здійснити шляхом ін’єкції струму у вихідний вимірювальний подільник напруги. Запропонований метод дозволяє одержати лінійну залежність приросту вихідної напруги від величини додаткового струму. Для цифрового керування блоком живлення може бути використаний набір ключів на польових транзисторах або цифро-аналоговий перетворювач. Most switching power supplies are not designed to change their output voltage. However, situations arise where a different voltage from the power source is needed. The purpose of this article is to develop a practical interface scheme for digitally controlling the output voltage of a switching power supply with an analog feedback loop.Item Combined system of automatic flow stabilization bread mass at the entry of the thresher of the grain harvester(ЦНТУ, 2024) Osadchy, S.; Vikhrova, L.; Kalich, V.; Miroshnichenko, M.; Осадчий, С. І.; Віхрова, Л. Г.; Каліч, В. М.; Мірошніченко, М. С.The research conducted in this article is devoted to solving the actual problem of loading the grain harvester with bread mass at the entrance of the thresher. It is possible to achieve the minimum level of fluctuations in the flow of bread mass at the entrance of the threshing-separating device only in appropriately designed optimal multidimensional stabilization systems. At the same time, the methods of dynamic design and analytical design should be used for the construction of similar systems. Проведені у даній статі дослідження присвячені вирішенню актуальної проблеми завантаження зернозбирального комбайну хлібною масою на вході молотарки. Досягти мінімального рівня коливань потоку хлібної маси на вході молотильно-сепаруючого пристрою можна тільки у відповідним чином спроектованих оптимальних багатовимірних системах стабілізації. При цьому слід застосовувати методи динамічного проектування та аналітичного конструювання за побудови подібних систем.Item Інформаційна технологія проектування системи автоматичної стабілізації потоку хлібної маси на вході до молотарки зернозбирального комбайну(ЦНТУ, 2022) Осадчий, С. І.; Віхрова, Л. Г.; Каліч, В. М.; Мірошніченко, М. С.; Osadchiy, S.; Vikhrova, L.; Kalich, V.; Miroshnichenko, M.В статті наведено нову методологію створення інформаційної технології проектування комбінованої системи стабілізації потоку хлібної маси на вході до молотарки зернозбирального комбайну. Окреслено характерні риси подібної методології. Це дозволяє здійснювати проектування систем керування технологічними процесами на комбайні з урахуванням зовнішніх впливів, які мають стохастичний характер. Обґрунтовано стадії створення інформаційної технології синтезу оптимальної комбінованої системи стабілізації зі зворотнім зв’язком за відхиленням хлібної маси від середнього значення та корекцією за зміною врожайності. The article presents a new methodology for creating information technology for the design of a combined system for stabilizing the flow of bread mass at the entrance to the combine thresher. The characteristic features of such a methodology are outlined. This allows the design of process control systems on the combine, taking into account external influences that are stochastic in nature. The stages of creation of information technology for the synthesis of the optimal combined stabilization system with feedback on the deviation of the bread weight from the average value and correction for changes in yield are substantiated. The article substantiates the composition and determines the content of operations of the new information technology of designing a combined system of stabilization of the flow of bread mass at the entrance to the thresher of the combine. The new technology has several distinctive features. First, its introduction allows to obtain differential equations of the combine harvester, which take into account the dynamic properties and design features of hydraulic transmissions operating in the mode of constant load change. Secondly, it allows you to design process control systems on the combine, designed for external influences that are stochastic in nature. Third, the new technology allows the synthesis of optimal combined stabilization systems under the conditions of two multidimensional independent sources of disturbance at the input and output of the stabilization object.Item Метод синтезу оптимального багатовимірного фільтру для виділення регулярного сигналу на фоні випадкових перешкод(ЦНТУ, 2021) Осадчий, С. І.; Дідик, О. К.; Сербул, О. М.; Каліч, В. М.; Osadchiy, S.; Didyk, O.; Serbul, O.; Kalich, V.В даній статті приводиться дослідження можливості застосування комплексування вимірювальної інформації в умовах, коли корисна інформація являє собою вектор регулярних сигналів, а завади вимірювання – багатовимірний стаціонарний випадковий процес. In terms of [1] we formulate the problem of synthesis of a complex system of allocation of a useful regular signal. Suppose that a multidimensional stationary filter best processes the input information about the same regular signal r(t), which is obtained by several "non-ideal" meters, and the result is transmitted to the evaluation system. In this article, a multi-channel measurement system, which is connected to the input of a multidimensional data transmission system, the dynamics of which is described by a system of linear differential equations. The input of the measuring system receives an n-dimensional vector of measured signals r (t), the components of which are deterministic functions. The vector r (t) belongs to the main group of "non-ideal" meters. Measurements are accompanied by interference, which is a random stationary process with zero mathematical expectation and a known fractional-rational matrix of spectral densities. An integral indicator of the quality of the system is the sum of the weighted integral quadratic error of the regular signal estimation and the variance of the random component of the error. Thus, a new algorithm for the synthesis of a complete optimal regular signal extraction system against the background of a multidimensional stationary random interference is obtained, which allows to find the structure and parameters of a multidimensional optimal filter taking into account the dynamics of the information transmission system.Item Технології організації дистанційного навчання в Україні(ЦНТУ, 2021) Голик, О. П.; Каліч, В. М.; Жесан, Р. В.; Волков, І. В.; Holyk, O.; Kalich, V.; Zhesan, R.; Volkov, I.В статті виконано огляд та аналіз технологій для дистанційної форми навчання в Україні, їх переваги та недоліки. Запропоновано заходи для покращення ефективності організації дистанційної форми навчання. To prevent the spread of coronavirus infection, educational institutions from time to time switch to distance learning. The article reviews the ways of organizing distance learning in Ukraine, existing technologies for distance learning, electronic resources, and educational platforms. The most common web services for online learning are considered. The advantages and disadvantages of distance learning in the conditions of classical education are determined. As a result, it was found that the disadvantages outweigh the advantages, which significantly affects the quality of education as a whole. The main disadvantages: the low level of digital literacy, insufficient control over the acquisition of knowledge, and lack of social interaction between peers. Despite these shortcomings, the organization of distance learning by the Ministry of Education and Science of Ukraine and educational institutions is performed at a sufficient level. However, this process needs to be improved in terms of privacy, data protection and digital literacy. To address the lack of proper parental control, it is proposed at the state level to provide parents with the opportunity to be present directly during their children's distance learning, while being able to maintain their jobs and wages.Item Дослідження САУ процесу РОД на верстаті з електромеханічним приводом. ІI. Інформаційно-вимірювальний комплекс для проведення експериментальних досліджень(КНТУ, 2012) Савеленко, Г. В.; Єрмолаєв, Ю. О.; Каліч, В. М.; Savelenko, G.; Ermolaev, Y.; Kalich, V.В статті розглянутий інформаційно-вимірювальний комплекс, що дозволяє проводити реєстрацію основних технологічних параметрів процесу РОД на верстаті розмірної обробки дугою з електромеханічним приводом. The article discusses the information measuring system which allows registration of the main technological parameters of the ROD on the machine dimensional processing of arc with an electromechanical drive.Item Математичне і комп’ютерне моделювання розподілу температур в теплиці для створення системи управління(КНТУ, 2011) Віхрова, Л. Г.; Каліч, В. М.; Прокопенко, Т. О.; Vikhrova, L.; Kalich, V.; Prokopenko, T.На основі розробленої математичної моделі і створеного програмного забезпечення проведений чисельній аналіз розподілу температури в приміщенні теплиці. Комп’ютерне моделювання температурних полів важливе при прогнозуванні параметрів мікроклімату теплиці в залежності від зовнішніх і внутрішніх факторів та забезпеченні іх необхідного діапазону і стабільності. On the basis of the developed mathematical model and created software an analysis of features of distributing of temperature was conducted numeral in the apartment of hothouse. The design of the computer temperature fields is important at prognostication of parameters of microclimate of hothouse depending on external and internal factors and providing of their necessary range and stability.