Збірники наукових праць ЦНТУ
Permanent URI for this communityhttps://dspace.kntu.kr.ua/handle/123456789/1
Browse
3 results
Search Results
Item Технічне забезпечення ін’єкційного зрошення овочевих культур(ЦНТУ, 2021) Васильковська, К. В.; Ковальов, М. М.; Андрієнко, О. О.; Vasylkovska, K.; Kovalov, M.; Andriienko, O.В статті запропоновано схему краплинного зрошення ін’єкційного типу для вирощування овочевих культур на присадибній ділянці. В запропонованій конструкції для краплинного зрошення розраховано схему та необхідну кількість розміщення трубок з крапельницями та мікротрубок із кілочками для подачі води в підґрунтовий простір кореневої системи рослин. На ділянці під овочеві культури використано ємність для фертигації – введення рідини в зрошувальну систему для підживлення рослин, задля захисту їх від стресів, покращення розвитку та збільшення врожайності. Проведена серія досліджень із забезпечення вологою ділянки у зоні формування коренів і збереження повітрообміну ґрунту та їх впливу на врожайність томатів. Використання краплинного зрошення ін’єкційного типу дало змогу збільшити врожайність до 40% та при цьому економно витрачати воду. With the change of climatic conditions, both in Ukraine and in the world, there is a need to provide vegetable crops with light, air and water in full, so the use of injectable irrigation for agricultural production is a prerequisite for sustainable future crops and a new challenge for producers of agricultural products. In climate change, irrigation of vegetable crops has a decisive impact on yields, especially in dry and hot summers. The technological process of growing vegetable crops necessarily includes the following components: quality seeds with high genetic potential, irrigation, fertilizers, plant prot ection and mechanization of all stages of the technological process. Combining these main elements of technology with strict adherence to the rules of application and timing of all operations, is the basis for obtaining high and stable yields of vegetable crops. Therefore, drip irrigation is an indispensable component of this technological process, its powerful stabilizing factor. The article proposes a scheme of injectable drip irrigation for growing vegetables in the backyard. In the proposed design for drip irrigation, the scheme and the required number of placement of tubes with droppers and microtubes with pegs for water supply to the subsoil space of the root system of plants are calculated. In the area under vegetable crops, a container for fertigation was used - the introduction of liquid into the irrigation system to feed the plants, to protect them from stress, improve development and increase yields. A series of studies was conducted to provide moisture to the area in the area of root formation and preservation of soil air exchange and their impact on tomato yield. The use of injectable drip irrigation has increased yields by up to 40% while saving water. Thus, with the change of climatic conditions, most of the Kirovohrad region fell into the zone of risky agriculture, due to which there was an urgent need for the use of irrigation systems for agricultural plants. Injection-type drip irrigation is most effective in intensive cultivation of row crops and vegetables, when the condition of the plant largely depends on the accuracy of maintaining the humidity in the root zone and plant nutrition. Drip irrigation of the injection type allows you to increase the yield of vegetable crops while economically using water resources.Item Технічне та технологічне забезпечення краплинного зрошення овочевих культур(ЦНТУ, 2020) Васильковська, К. В.; Ковальов, М. М.; Молокост, Л. А.; Vasylkovska, K.; Kovalov, M.; Molokost, L.; Васильковская, К. В.; Ковалев, Н. Н.В статті запропоновано схему краплинного зрошення для вирощування овочевих культур на присадибній ділянці. Проведена серія досліджень із забезпечення вологою ділянки та збереження повітрообміну ґрунту. Запропоновано розрахунок та схему краплинного зрошення стрічкового типу. В запропонованій конструкції для краплинного зрошення ділянки під овочеві культури використано ємність з водою для забезпечення невеликого постійного тиску води в стрічках. Це дало змогу здійснювати полив за необхідністю, а також використовувати ємність для розчину для підживлення рослин, захисту їх від стресів, покращення розвитку та збільшення врожайності. Використання краплинного зрощення дало змогу з’явитись першим плодам на декаду раніше та збільшити врожайність на 25-50%. The article proposes a scheme of drip irrigation for growing vegetables in the backyard. In the conditions of change of climatic conditions, the question of lack of moisture sharply arises. For growing vegetables in areas of risky agriculture, irrigation is an important condition for obtaining high yields. In order to increase the technological efficiency of growing vegetables at the department of general agriculture of the Central Ukrainian National Technical University developed a prototype of a drip irrigation system for vegetables. A series of studies was conducted to provide moisture to the site and preserve soil air exchange. With the use of conventional irrigation, possible negative consequences in the form of soil flooding, the root system of plants is not able to develop evenly and is deficient in oxygen. The calculation and the scheme of drip irrigation of tape type are offered. In the proposed design for drip irrigation of the area under vegetable crops used a container with water to provide a small constant water pressure in the strips. This made it possible to water as needed, as well as to use a solution tank to feed the plants, protect them from stress, improve development and increase yields. The use of drip splicing allowed the first fruits to appear a decade earlier and increase yields by 25-50%. The use of drip tape irrigation system on the experimental plots allowed to increase the quantity and quality of tomato harvest. Also, the use of drip irrigation allowed to maintain the optimal water-physical regime in the root layer of the soil, which created the conditions for a better harvest. Thus, with the change of climatic situation, most of the Kirovohrad region was looking for in the zone of risky agriculture. Drip irrigation has an almost universal application, is effective in intensive technologies for growing crops and ornamental crops, as well as in garden areas, when the condition of the plant largely depends on the accuracy of maintaining the humidity and nutrition of plants. В статье предложена схема капельного орошения для выращивания овощных культур на приусадебном участке. Проведена серия исследований по обеспечению влагой участка и сохранения воздухообмена почвы. Предложено расчет и схему капельного орошения ленточного типа. В предлагаемой конструкции для капельного орошения участка под овощные культуры использовано емкость с водой для обеспечения небольшого постоянного давления воды в лентах. Это позволило осуществлять полив при необходимости, а также использовать емкость для приготовления раствора для подкормки растений, защиты их от стрессов, улучшения развития и увеличения урожайности. Использование капельного орошения позволило появиться первым плодам на декаду раньше и увеличить урожайность на 25-50%.Item Визначення закономірностей зношування шийок колінчастих валів двигунів транспортних засобів(ЦНТУ, 2019) Ковальов, М. Ф.; Головащук, М. В.; Ковалев, М. Ф.; Kovalov, M.; Holovaschchuk, M.Забезпечення необхідних експлуатаційних показників двигунів транспортних засобів на сучасному етапі розвитку автомобілебудування та авторемонтного виробництва потребує поліпшення їх технічних характеристик. Однією з основних причин передчасного виходу з ладу двигунів транспортних засобів є знос трибосистеми шийки колінчастого вала - підшипника ковзання. В статті проведено аналіз закономірностей зношування корінних і шатунних шийок колінчастих валів двигунів транспортних засобів. Досліджено особливості зносу корінних та шатунних шийок колінчастих валів. Обеспечение необходимых эксплуатационных показателей двигателей транспортных средств на современном этапе развития автомобилестроения и авторемонтного производства требует улучшения их технических характеристик. Одной из основных причин преждевременного выхода из строя двигателей транспортных средств является износ трибосистемы шейки коленчатого вала - подшипника скольжения. В статье проведен анализ закономерностей изнашивания шеек коленчатых валов двигателей транспортных средств. Исследованы особенности износа коренных и шатунных шеек коленчатых валов. The purpose of the article is to analyze the regularities of the wear characteristics of the crankshafts of vehicles engines depending on the magnitude of the load on the friction surface, which continuously changes the gap between the rubbing surfaces, the hardness and cleanliness of the machined surfaces, the speed of relative movement of parts, viscosity, temperature and purity of oil, etc. In accordance with the stated goal, the article explores the peculiarities of the wear of the crankshafts and crankshafts. Providing the necessary operational performance of vehicle engines at the present stage of development of automotive and auto repair production requires improvement of their technical characteristics. One of the main causes of premature failure of vehicles engines is the wear of the tribosystem of the crankshaft neck - the sliding bearing. Wear of the crankshaft necks leads to a gradual change in their size, shape and condition of the surfaces due to the interaction of thin metal surface layers in the friction process. The nature of wear and tear patterns over time is explained by a number of non-random causes. These include: change in the contact area of the elements in the wear probe, change in the physical and mechanical properties of the materials of the parts in depth, increase in dynamic loads and deterioration of lubrication conditions as the gaps in the joints increase, etc. Thus, the leading process of wear of the tribosystem of the neck of the crankshaft - the sliding bearing is mechanical wear, which includes abrasive and fatigue wear. One of the main causes of premature failure of engines after major repairs, and in particular, the crankshaft cervical tribosystem - sliding bearing, is the level of methods used and the quality of strengthening of the crankshaft and crankshaft crankshafts. Therefore, the problem of increasing the wear resistance of the crankshaft crankshafts and crankshafts and in the whole life of the pair of crankshaft friction pairs - the sliding bearing is relevant today.