Збірники наукових праць ЦНТУ
Permanent URI for this communityhttps://dspace.kntu.kr.ua/handle/123456789/1
Browse
2 results
Search Results
Item Зміцнення деталей з алюмінієвих сплавів мікродуговоговим оксидуванням(ЦНТУ, 2021) Кулєшков, Ю. В.; Красота, М. В.; Руденко, Т. В.; Осін, Р. А.; Крошка, В. Д.; Kuleshkov, Yu.; Krasota, M.; Rudenko, T.; Osin, R.; Kroshka, V.У статті наведено результати аналізу можливості використання нового способу зміцнення робочих поверхонь деталей – мікродугового оксидування для підвищення зносостійкості робочих поверхонь деталей, виготовлених з алюмінієвих сплавів, зокрема корпусів шестеренних насосів типу НШ. У роботі викладена сутність процесу зміцнення деталей мікродуговим оксидуванням, представлені основні фізико-механічні характеристики зміцнюючого покриття. Відзначено, що міцність зчеплення і механічні властивості покриття багато в чому залежать від стану зміцнюючої поверхні, зокрема від методу попередньої обробки. При цьому встановлено, що зміцнюючі покриття металу після пластичного деформування мають більшу міцність зчеплення, більшу товщиною і твердістю. Представлені основні відомості про мікродугове оксидуванні, які на думку авторів будуть сприяти освоєнню маловивченого способу зміцнення в ремонтному виробництві. The purpose of the research is to analyze the scientific and technical information to determine the possibility of strengthening the parts of aluminum alloys by microarc oxidation, in particular gear pump housings. The article presents the results of the analysis of possibility of using a new method of hardening roboczych surfaces - micro-arc oxidation to enhance the wear resistance of working surfaces of parts made of aluminum alloys, in particular housings, gear pumps NSH. The paper describes the essence of the process of hardening parts by microarc oxidation, presents the main physical and mechanical characteristics of the hardening coating. It is noted that the adhesion strength and mechanical properties of the coating largely depend on the state of the surface to be strengthened, in particular, on the method of pretreatment. At the same time, it was found that the strengthening coating of the metal after plastic deformation has a greater adhesion strength, greater thickness and hardness. The paper presents the basic information about microarc oxidation, which, according to the authors, will contribute to the development of the method in the poorly studied method of hardening in repair production. It can be concluded that the ceramic coatings obtained by microarc oxidation can be recommended for the restoration and strengthening of aluminum parts of gear pumps, in particular the pump housing.Item Використання мікродугового оксидування при зміцненні деталей з алюмінієвих сплавів, відновлених пластичним деформуванням(ЦНТУ, 2017) Кулєшков, Ю. В.; Красота, М. В.; Руденко, Т. В.; Матвієнко, О. О.; Kuleshkov, Y.; Krasota, M.; Rudenko, T.; Matvienko, A.У статті приведений аналіз можливості використання нового способу зміцнення - мікродугового оксидування для підвищення зносостійкості деталей, виготовлених з алюмінієвих сплавів, зокрема корпусів шестеренних насосів типу НШ. У роботі викладена сутність процесу зміцнення деталей мікродуговим оксидуванням, представлені основні фізико-механічні характеристики зміцнюючого покриття. Відзначено, що міцність зчеплення і механічні властивості покриття багато в чому залежать від стану поверхні, що зміцнюється, зокрема від методу попередньої обробки. При цьому встановлено, що зміцнюючі покриття після пластичного деформування деталей мають вищу міцність зчеплення, твердість і більшу товщину. У роботі представлені основні відомості про мікродугове оксидуванні, які на думку авторів будуть сприяти застосуванню маловивченого способу зміцнення в ремонтному виробництві. The objective of the research is to analyse the scientific and technical information on hardening of parts of aluminium alloys by micro-arc oxidation, particularly the parts, which were repaired by hot plastic deformation. This article presents the analysis of the possibility to apply a new method of hardening of working surfaces of parts by micro-arc oxidation to increase wearability of working surfaces of the parts made of aluminium alloys, in particular the bodies of gear pumps. The work presents the essence of the process of hardening of details by micro-arc oxidation and the main physical and chemical characteristics of the hardening coating. It was stated that the adhesive strength and mechanical characteristics of the coating largely depend on the condition of the surface under hardening, in particular on the method of preparatory processing. It was established that the hardening coating of metal after plastic deformation gets better adhesive strength, thickness and hardness. The work presents basic information on micro-arc oxidation which will facilitate further application of the hardening method in repair industry.