Збірники наукових праць ЦНТУ
Permanent URI for this communityhttps://dspace.kntu.kr.ua/handle/123456789/1
Browse
2 results
Search Results
Item Аналіз роботи пневмомеханічного висівного апарата з периферійним розташуванням комірок(КНТУ, 2013) Васильковська, К. В.; Петренко, М. М.; Гончарова, С. Я.; Vasylkovska, Ekaterina; Petrenko, Nikoly; Goncharova, SvetlanaПроведено аналіз роботи пневмомеханічного висівного апарата з периферійним розташуванням комірок. Доведено, що для гарантованого сходження зайвого насіння відцентрова сила повинна перевищувати силу тяжіння насінини. Складено диференційне рівняння руху частки в полі діючих сил, при вирішенні якого отримано залежності переміщення частки по лопатці від кута обертання диску при різних кутових швидкостях. Analysis of the design of the proposed sowing device suggests a possibility of capture, seeds, movement and dumping them , even without the use of vacuum. But guaranteed to shift the main seed furrow necessary to use more force that it be kept in the cell. Found that to guarantee convergence excess seed centrifugal force must exceed the force of gravity seed. Done differential equation of motion particle in the field of active forces in dealing with any dependencies particles moving in a pan on the angle of rotation of the disk at different angular velocities. The presence of suction power , can increase the size of the cavity passive trunk seed to 0.26 ... 0.30 radians in angular velocity of the disk 30 ... 25 radians per second. This will guaranteed to remove those extra seeds , as they move around the pan more than half their own diameter. A basic seed, thanks to the force of suction , securely held in a cell and transported to the area of a disk reset.Item Експериментальні дослідження пневмомеханічного висівного апарата для висіву насіння просапних культур(КНТУ, 2014) Васильковський, О. М.; Абрамова, В. В.; Васильковська, К. В.; Петренко, Д. І.; Vasylkovskiy, Aleksey; Abramova, Viktoria; Vasylkovska, Ekaterina; Petrenko, DmitriyВ статті розглядається серія експериментальних досліджень нового пневмомеханічного висівного апарата для висіву насіння просапних культур. Результати досліджень свідчать про можливість підвищення ефективності точного висіву. The aim is to obtain precise seeding evenly placed on the area of the field plants, which, in this case, have the same area and power developing best. The uniformity of seed placement in the line depends on the uniformity of seed placement on the seed disc, which requires properly orient the seed at the stage of seed capture drive. In order to improve precision seeding cultivated crops at the Department of Agricultural Engineering Kirovograd National Technical University has developed and manufactured a prototype of a new pneumomechanical sowing device, the main feature of which is the presence of extra seed disk that thanks to the original design directs seed to suction hole. Moreover, at suction hole located just one seed. If captures two seed, the second seed is above the upper edge of the extra drive and completely removes unnecessary seeds. In the article the new series of experimental studies pneumomechanical sowing device for sowing seeds of cultivated crops. The research results indicate the possibility of increasing the efficiency of precise seeding. Analysis of response surfaces for fill factor cells of seed disk, to determine the optimal values of the studied factors, namely: value of additional disk thickness should be in the range of 1.4 to 1.6 mm; radius cavity additional disk should be in the range of 3 to 3.2 mm; value of vacuum in the vacuum chamber should be in the range of 2.0 to 2.4 kPa; the rotational speed of the sowing disc cells should be in the range of 0.22 to 0.26 m/s.