Збірники наукових праць ЦНТУ
Permanent URI for this communityhttps://dspace.kntu.kr.ua/handle/123456789/1
Browse
3 results
Search Results
Item Аналіз конструкцій глушників вакуумних насосів(ЦНТУ, 2024) Хмельовський, О. В.; Khmelovskyi, O.Виконано обґрунтування конструкційно-функціональної схеми фільтра-глушника роторно-лопатевого вакуумного насосу, який має можливість відділяти оливу від повітря та збирати її для подальшого переробітку. Запропонована конструкція, завдяки конструкційній особливості, забезпечує гасіння звуку, знижує шум та має мінімальний опір рухові повітряного потоку в середині фільтра-глушника. Конструкція фільтра-глушника, умовно, може бути розділена на дві конструкційні частини, кожна з яких виконує свою функцію. В роботі встановлені аналітичні зв’язки технологічних характеристик процесу відділення оливи від повітря із врахуванням швидкості повітря на вході в глушник. Встановлено взаємозв'язок між продуктивністю насоса і конструктивними параметрами фільтра-глушника. У виробничих умовах досліджено, що відокремлення оливи від повітря, в запропонованому фільтрі-глушнику, складає 93-95%, а величина зниження шуму становить 15-22 дБ. The substantiation of the structural and functional scheme of the muffler filter of the rotary vane vacuum pump, which has the ability to separate oil from air and collect it for further processing, has been completed. The proposed design, due to its design feature, provides sound suppression, reduces noise and has minimal resistance to the movement of the air flow in the middle of the muffler filter. The muffler filter is based on the fact that air, together with the oil that lubricates the vacuum pump nodes, enters the muffler filter through the inlet pipe at a speed of 11...16 m/s, which allows the most complete separation of oil from air. The trajectory of the movement of air in the muffler is described by a helical winding, and therefore, centrifugal force acts on the oil particles in a suspended state, as a result of which the oil particles are thrown to the sieve catcher, the oil is separated from the air and enters the interwall space of the housing and the sieve catcher, and flows down into the oil sump, from where it is drained using a tap. After that, it can be sent for processing, or, after cleaning, enter the pump lubrication system. The oil-free air continues to move over the surface of the screw winding, and due to the change in the pitch of the screw winding, the air decreases its speed, as a result of which the noise level decreases and oil content is cleaned more efficiently. Air passes to the top cover and enters the environment through the outlet pipe.Item Технічне забезпечення гідропоніки, як прогресивного виду вирощування овочевих культур(ЦНТУ, 2022) Васильковська, К. В.; Ковальов, М. М.; Андрієнко, О. О.; Корнічева, Г. І.; Vasylkovska, К.; Kovalov, М.; Andriienko, О.; Kornicheva, Н.В статті запропоновано схему гідропонної установки (NFT) для вирощування зелених овочевих культур в умовах закритого ґрунту. Вирощування зелених овочевих культур в умовах гідропонних систем дає можливість отримувати врожай цілий рік, при чому в об’ємі набагато більшому ніж за ґрунтових умов. Розроблена конструкція гідропонної системи дає можливість отримувати сталий врожай рослин салату при використанні субстрату. Використана установка системи NFT із використанням поживного розчину мінерально-біологічних препаратів дозволяє отримати розсаду з добре розвиненою кореневою системою та надземною частиною. Проведені дослідження дали змогу отримати врожайність, що переважає врожайність в ґрунтових умовах на 10-15%, а в перерахунку на рік – в 5,0-5,5 рази. The aggravation of the food crisis and the impossibility of exporting agricultural products from the ports against the backdrop of the war in Ukraine only exacerbates the issue of food security. The purpose of writing the article is to substantiate the installation scheme for hydroponic cultivation of vegetable crops in closed soil conditions for obtaining stable harvests of vegetable crops throughout the year. To carry out research, a hydroponic plant that works on the principle of a nutrient layer (NFT) was developed and manufactured at the Department of General Agriculture of the Central Ukrainian National Technical University. The installation is designed for growing green vegetable crops. A coconut-agroperlite soil mixture was used as a substrate. The used installation is compact, provided with a lighting system and works in automatic mode. The useful area of the installation is 0.104 m2, so it is possible to grow from 40 to 112 lettuce plants at the same time. The use of a mineral solution in a hydroponic installation had a significant effect on the growth and development of lettuce plants and caused an increase in the area of leaf plates. In the experiment, the yield of Tudela variety lettuce was obtained - 4.9 kg/m2, which is 10-15% more than in soil conditions, and if the installation is used all year round - 5.0-5.5 times more. The advantage of the method is that there is no need to use fungicides. Since, without the presence of soil, there are no such pests as cabbageworm and sciaridis. And the biggest advantage is saving water and controlling the substances they absorb in the process of development. The latest systems of growing green vegetable crops in the conditions of hydroponic systems make it possible to harvest all year round, and in a much larger volume than under soil conditions. The developed design of the hydroponic system makes it possible to obtain a steady crop of lettuce plants when using a coconutagroperlite soil mixture as a substrate. The proposed installation of the NFT system using a nutrient solution of mineral-biological preparations made it possible to obtain seedlings with a well-developed root system and an above-ground part with a yield of 4.9 kg/m2.Item Разработка установки для опреснения воды методом вымораживания(КНТУ, 2013) Барабаш, П. А.; Голубев, А. Б.; Трокоз, Я. Е.; Горин, В. В.; Барабаш, П. О.; Голубєв, О. Б.; Трокоз, Я. Е.; Горін, В. В.; Barabash, Petr; Golubev, Aleksey; Trokoz, Yaroslav; Gorin, YaroslavВ работе представлена установка, предназначенная для опреснения воды методом вымораживания с деформируемой льдогенерирующей поверхностью теплообмена. В роботі наведена установка, яка призначена для опріснення води методом виморожування з дерформуючою льдогенерирующею поверхнею теплообміну. This work presents a plant intended for desalination method of freezing with deformable ice generating heat exchange surface. Developed by installing УОВВ-100 is intended for desalination method of freezing with deformable льдогенерирующей surface heat transfer. Plant capacity - 100 l/h water with salt content 0,001...0,5 g/l (initial≈ 0.5 to 30 g/l). Installations are intended use in medical, food, meat and dairy industries. The main element of desalination plants such freezing type is ice (LH). The efficiency of the LH depends on the efficiency of operation of the plant for desalination method of freezing. Design LH takes into account technical innovations, a set of applications which gives a new technical and economic effect. Energy cost deformation льдообразующей surface significantly lower the energy cost cutting ice. Tests proved the capacity of the proposed design ice machine and allowed to determine the approximate value of the frequency of deformations (ω = 20 min-1) to obtain the maximum specific performance ice machine g= 260 kg/m2h.