Збірники наукових праць ЦНТУ
Permanent URI for this communityhttps://dspace.kntu.kr.ua/handle/123456789/1
Browse
2 results
Search Results
Item Аналіз конструктивних особливостей машин для очищення насіння рицини(ЦНТУ, 2025) Теслюк, Г. В.; Головченко, В. В.; Tesliuk, H.; Golovchenko, V.У статті проведено аналіз сучасного стану розвитку технологій очищення насіння рицини та виявлено основні недоліки існуючих рішень. Встановлено, що традиційні методи лущення, засновані на механічному впливі (тертя, стиснення, удар), мають низьку ефективність, призводять до значного пошкодження насіння та потребують удосконалення для підвищення якості очищення. Проведено класифікації принципових схем будови робочих зон машин для розлущування плоду та відокремлення насіння рицини та машин для очищення насіннєвої суміші. Встановлено, що під час технологічних операцій розлущування плоду і відокремлення насіння рицини утворюється суміш, яка містить три основні компоненти: нерозлущені або частково розлущені плоди (великі важкі компоненти), насіння рицини (середні компоненти) і лушпиння (маленькі легкі компоненти). У цьому випадку найкраще використовувати аеродинамічну сепарацію суміші з елементами решітного сепаратора. З урахуванням цього складено технологічну схему машини для очищення насіння рицини, основними робочими органами якої є нерухома гумова дека, рухомий вертикальний конусоподібний гумовий валок, решето і циклонний сепаратор. Надалі передбачено розробку конструкції машини для очищення насіння рицини на базі розробленої технологічної схеми, обґрунтування її конструктивно-технологічних параметрів, виготовлення і впровадження у виробництво. The article analyzes the current state of development of castor seed cleaning technologies and identifies the main drawbacks of existing solutions. It has been established that traditional hulling methods based on mechanical impact (friction, compression, impact) have low efficiency, cause significant seed damage, and require improvement to enhance cleaning quality. A classification of the fundamental structural schemes of working zones in machines for hulling castor fruits, separating castor seeds, and cleaning seed mixtures has been conducted. It has been determined that during the technological operations of hulling castor fruits and separating seeds, a mixture is formed that consists of three main components: unhulled or partially hulled fruits (large heavy components), castor seeds (medium components), and husks (small light components). In this case, the best approach is to use aerodynamic separation of the mixture combined with elements of a sieving separator. Based on this, a technological scheme for a castor seed cleaning machine has been developed, with the main working elements being a stationary rubber deck, a movable vertical conical rubber roller, a sieve, and a cyclone separator. Further work includes the development of the machine’s design based on the proposed echnological scheme, justification of its structural and technological parameters, manufacturing, and implementation in production.Item Виробничі випробування пневматичного сепаратора на попередньому очищенні насіннєвих сумішей цибулі(ЦНТУ, 2019) Бакум, М. В.; Крекот, М. М.; Абдуєв, М. М.; Бакум, Н. В.; Крекот, Н. Н.; Абдуев, М. М.; Bakum, M.; Krekot, M.; Abduev, M.Наведені результати виробничих випробувань модернізованого пневматичного сепаратора з регульованою шириною сепарувального каналу на попередньому очищені дрібнонасіннєвої суміші цибулі з великим вмістом легких домішок. В результаті первинної обробки насіннєвого вороху цибулі, отриманого після машинного збирання насінників, на удосконаленому пневматичному сепараторі відокремлено 48,62% від маси вихідної суміші насіннєвого матеріалу, посівні властивості якого відповідають вимогам державного стандарту на посівний матеріал. Приведены результаты производственных испытаний модернизированного пневматического сепаратора с регулируемой шириной сепарирующего канала на предварительной очистке мелкосеменной смеси лука с большим содержанием легких примесей. В результате первичной обработки семенного вороха лука, полученного после машинной уборки семенников, на усовершенствованном пневматическом сепараторе отделено 48,62% от массы исходной смеси семенного материала, посевные свойства которого соответствуют требованиям государственного стандарта на посевной материал. The arid summer of 2019 significantly complicated the cultivation of crops. This is especially true for crops of medium and late ripening. These crops include most vegetable crops. Weather conditions caused a significant decrease in seed yield and a decrease in their sowing qualities. In addition, they contributed to the drying of stems and inflorescences during the harvesting period. Machine cleaning of such testes leads to the ingress of a significant amount of crushed stems and inflorescences of different sizes into the seed material. Most of them are lighter from the seeds of the main crop. They mainly comprise light impurities of the obtained seed material. A large number of light impurities reduces the flowability of seed material. This significantly reduces the effectiveness of traditional methods of post-harvest processing of seed material. The aim of the work is to study the features of using an improved pneumatic separator with a tilted channel in the preliminary cleaning of fine seed mixtures with a high content of light impurities. Presented are the results of production tests of a modernized pneumatic separator with an adjustable width of the separating channel for preliminary cleaning of onion seed mixture with a high content of light impurities. As a result of the primary processing of onion seed heap obtained after mechanized harvesting of testes on an improved pneumatic separator, 48.62% of the weight of the initial mixture, seed material, the sowing properties of which meet the requirements of the standard for seed, is purified. At the same time, the content of the first receiver, which is 41.16% of the mass of the starting material, or 84.66% of the content of the first two fractions, can be cleaned up to the requirements of the standard by traditional seed cleaning machines. The seed fraction of the second receiver must be further cleaned on an advanced pneumatic separator with modified air flow parameters in order to additionally separate, especially light impurities. The content of the third, fourth and fifth receivers is 51.32% of the mass of the source material, it is advisable to use it for another purpose, which will contribute both to improving the quality of the prepared seed and to reduce the cost of its preparation.