Збірники наукових праць ЦНТУ
Permanent URI for this communityhttps://dspace.kntu.kr.ua/handle/123456789/1
Browse
3 results
Search Results
Item Вплив параметрів розподільника на якість розсіювання добрив у підлаповому просторі(ЦНТУ, 2020) Дейкун, В. А.; Артеменко, Д. Ю.; Дейкун, С. І.; Deikun, V.; Artemenko, D.; Deikun, S.; Артёменко, Д. Ю.; Дейкун, С. И.У статті представлені результати теоретичного дослідження процесу транспортування та розподілу гранул мінеральних добрив після відбиття від площини розподільника у підлаповому просторі плоскоріжучого робочого органу. Обґрунтовані геометричні параметри та кути розташування площини відбиття. The aim of the work is to substantiate the geometric parameters of the distributor, which are able to provide the maximum range of fertilizer particles in the subclavian space, based on the analysis of all factors affecting the material particles during their transportation to the surface of the distributor. The result of research is to achieve a uniform distribution of fertilizers on the width of the capture and, accordingly, on the area. It is known that the particles of material sent in accordance with the given trajectories in the pre-provided areas of the surface of the furrow formed by the working body, in contact with the soil are significantly redistributed and the meaning of the traditional approach to uniformity is completely lost. In addition, it is necessary to take into account that for placing fertilizers in the soil, in most cases, flat-cutting working bodies are used. For normal operation, in terms of deepening into the ground, they must be installed with a forward tilt at an angle of up to 3°. As a result, the bottom of the furrow, which they form, acquires a conical shape with a slope to the center. In this case, it becomes obvious that the material must be fed not evenly across the width of the working body, and most of it to be directed at a clearly defined distance in the direction perpendicular to its axis. The numerical value of this distance is determined by the nature of the redistribution of the granules as a result of contact with the soil. In the process of rolling the granules or particles to the center, the uniformity of distribution will be restored. In this case, it becomes obvious that the material must be fed not evenly across the width of the working body, and most of it to be directed at a clearly defined distance in the direction perpendicular to its axis. The numerical value of this distance is determined by the nature of the redistribution of the granules as a result of contact with the soil. In the process of rolling the granules or particles to the center, the uniformity of distribution will be restored. In this regard, there is a need to solve the problem of ensuring the maximum range of particles in the transverse direction using the simplest geometry of the distributor surface. In our opinion, such a surface can be a prism. In the article the results of theoretical research of process of portage and distributing of granules of mineral fertilizers are resulted after a reflection from the plane of reflection in sub paw space of trivial cutting of working organ. Geometrical parameters and corners of location of reflecting plane are grounded. The obtained dependences allow to reasonably establish geometrical parameters of the distributor which will provide the set range of flight of particles of material for working bodies of various width of capture and to reach desirable result taking into account laws of their redistribution at contact with soil. В статье представлены результаты теоретического исследования процесса транспортировки и распределения гранул минеральных удобрений после отражения от плоскости распределителя в подлаповом пространстве плоскорежущего рабочего органа. Обоснованы геометрические параметры и углы расположения плоскости отражения.Item Результати дослідження процесу роботи нового комбінованого робочого органа(ЦНТУ, 2018) Дейкун, В. А.; Deikun, V.За результатами проведених лабораторних досліджень процесу роботи експериментального комбінованого робочого органа оснащеного туконапрямником та розподільником для одночасного з основним безполицевим обробітком ґрунту внутрішньогрунтового внесення гранульованих мінеральних добрив з рівномірним їх розміщенням по площі в підлаповому просторі, встановлено технологічні та кінематичні параметри, які суттєво впливають на якість виконання технологічного процесу. Проведено оцінку впливу швидкості польоту гранул добрив на виході з туконапрямника, висоти розташування розподільника над поверхнею нижнього обрізу лапи, кута нахилу ребра призми та кута між її гранями на дальність поперечного польоту основної маси добрив та рівномірність їх розподілу за конструктивною шириною захвату. Конструкція комбінованого робочого органа для внутрішньоґрунтового внесення гранульованих мінеральних добрив обладнана пристроєм з обґрунтованими параметрами, який дозволяє спрямувати потік гранул добрив до точки їх контакту з гранями призми розподільника, після відбиття від якого вони спрямовуються у заданому напрямку. Запропонований робочий орган дозволяє рівномірно розмістити встановлену дозу мінеральних добрив на необхідну глибину з одночасною їх заробкою, що дозволяє знизити енерговитрати на виконання технологічної операції. По результатам проведенных лабораторных исследований процесса работы экспериментального комбинированного рабочего органа, оборудованного туконапрямителем и распределителем для одновременного с основной безотвальной обработкой почвы внутрипочвенного внесения гранулированных минеральных удобрений с равномерным их размещением по площади в подлапному пространстве, установлены технологические и кинематические параметры, которые существенно влияют на качество выполнения технологического процесса. Произведена оценка влияния скорости полета гранул удобрений на выходе из туконапрямителя, высоты расположения распределителя над поверхностью нижнего обреза лапы, угла наклона ребра призмы и угла между ее гранями на дальность поперечного полета основной массы удобрений и равномерность их распределения по конструктивной ширине захвата. Конструкция комбинированного рабочего органа для внутрипочвенного внесения гранулированных минеральных удобрений оборудована устройством с обоснованными параметрами, которое позволяет направить поток гранул удобрений к точке их контакта с гранями призмы распределителя, после отражения от которого они направляются в заданном направлении. Предложенный рабочий орган позволяет равномерно разместить установленную дозу минеральных удобрений на необходимую глубину с одновременной их заделкой, что позволяет снизить энергозатраты на выполнение технологической операции. According to the results of laboratory investigations of the work of the experimental combined work body. equipped with a tupon and a distributor for simultaneously with the main non-polar treatment of soil intra-ground introduction of granulated mineral fertilizers with uniform placement of them in the area under the slap space, technological and kinematic parameters that significantly affect the quality of the process, the impact of the flight speed of fertilizer granules on the exit from the tupon-strap, the height of the distributor's position above the surface of the lower edge of the paw, the angle of inclination of the edge of the prism and the angle between its faces on the distance the transverse flight of the main mass of fertilizers and the uniformity of their distribution on the design width of the trap. The design of a combined working body for intragrating granular mineral fertilizers is equipped with a device with well-defined parameters that allows the flow of granules of fertilizers to the point of their contact with the edges of the distributor prisms, after reflection of which they are directed in a given direction. The proposed working body allows uniform placement of the prescribed dose of mineral fertilizers to the required depth with their simultaneous earnings, which reduces energy costs for the implementation of technological operations.Item Дослідження дальності польоту частинок твердих мінеральних добрив шляхом моделювання(КНТУ, 2009) Ловейкін, В. С.; Човнюк, Ю. В.; Дитюк, А. І.; Loveykin, V.; Chovnyuk, U.; Dityuk, A.Завдяки проведеному всебічному дослідженню швидкості руху частинок твердих мінеральних добрив у середовищі з опором (повітрі), встановлено розмірний ефект, який визначає дальність польоту частинок добрив в залежності від їх фізико-механічних властивостей, параметрів їх польоту в момент сходження з розкидального диску, висоти установки диска над поверхнею поля, тощо. Because of the conducted investigations of the speed of the particle motion of the solid mineral fertilizers on Wednesday with the resistance (to air medium) is established size effect which it determines the flying range of particles depending on their physicomechanical properties, parameters of their flow at the moment of flight from the throwing about disk, height of the installation of the disk above the surface of field and others.