Збірники наукових праць ЦНТУ
Permanent URI for this communityhttps://dspace.kntu.kr.ua/handle/123456789/1
Browse
7 results
Search Results
Item Експериментальне дослідження залежності стійкості інструменту від інтенсивності охолодження і режимів різання(ЦНТУ, 2019) Лисих, А. Ю.; Будуров, В. Л.; Лысых, А. Ю.; Lisikh, A.; Bydyrov, V.У статті представлено експериментальне дослідження залежності стійкості інструмента від кількості мастильно-охолоджувальної рідини і витрат потужності при свердлінні свердлами зі змінними багатогранними пластинами, що дозволить збільшити період стійкості і зменшити витрати потужності при використанні багатогранних змінних пластин. В статье представлено экспериментальное исследование зависимости периода стойкости от расхода смазочно-охлаждающей жидкости и затрачиваемой мощности при сверлении свердлами с сменными многогранними пластинами, что позволит увеличить период стойкости и уменьшить затрачиваемою мощность при использовании многогранных сменных пластин. В статье представлено экспериментальное исследование зависимости периода стойкости от расхода смазочно-охлаждающей жидкости и затрачиваемой мощности при сверлении свердлами с сменными многогранними пластинами, что позволит увеличить период стойкости и уменьшить затрачиваемою мощность при использовании многогранных сменных пластин. It is presented in article experimental researches of the period of stability of variable many-sided plates of the cutting tool and power when drilling from intensity of cooling in a cutting zone. Such analysis is necessary for improvement of metal working of new structural materials and is of scientific and practical interest. The purpose of work is experimental researches on necessary amount of cooling liquid for ensuring the maximum stability of the tool that will allow to reduce expenses on the tool and will reduce prime cost of the manufactured products. The research concerning determination of necessary amount of cooling liquid for ensuring the maximum stability of the tool and also reduction power expenses is conducted. The experiment was conducted on the machine the processed center SPACE TURN LB 3000EX of Oruma to which the hydrometer in the system of supply of cooling liquid and a stop watch for fixation of time of measurement was built in. As the cutting tool it was used drills with replaceable plates of the following diameters of Ø20, Ø24, Ø28 of SEKO. As cooling liquid Akvol cooling liquid which similar to foreign brands was used. It is carried out to 10 single measurements of a consumption of cooling liquid and the period of stability and also capacities behind each of the modes it is sharp and calculation of average value is carried out. Results of a research are given in a type of graphic dependences that is confirmed by work conclusions. The analysis of the received results is made. Experimental researches are conducted showed that thanks to supply lubricant cooling liquid in a zone of cutting the coefficient of friction decreases and temperature in a cutting zone at the expense of what decreases the stability period to the tool increases. It is also established that at increase in giving of the tool and speed of cutting the period of stability decreases and increases power expenses. Practical application of these experimental researches will allow to reduce expenses on the tool and to reduce prime cost of the manufactured products.Item Алгоритм визначення допустимої товщини стінок напірних трубопроводів(КНТУ, 2014) Ковальчук, Н. В.Розроблена блок-схема розрахунку допустимої товщини стінок напірних трубопроводів для систем водопостачання дозволяє за будь-якою програмою виконати багато варіантів цих розрахунків за короткий час, а також визначити оптимальну товщину для кожного діаметра трубопроводу.Item Дослідження процесу взаємодії коренеплодів з витком шнека очисника(КНТУ, 2012) Дубчак, Н. А.; Dubchak, N.У статті наведено результати теоретичних досліджень процесу контактної взаємодії коренеплодів які рухаються на поверхні робочої гілки пруткового транспортера з робочими поверхнями шнека, який розташований над прутковим транспортером і поперечно напрямку руху його робочої гілки. Побудовано математичну модель, яка характеризує зміну кута відбивання коренеплодів після їх співудару з витком шнека залежно від параметрів процесу. На основі проведеного аналізу напрямку руху коренеплодів або кута відбивання коренеплодів після їх взаємодії з витком шнека обґрунтовано основні межі зміни конструктивно-кінематичних параметрів комбінованого очисника вороху коренеплодів. In the article the results of theoretical researches of process of contact co-operation of root crops are resulted which move on-the-spot working branch of twig conveyer with the workings surfaces of screw which is located above a twig conveyer and transversal direction of motion his working branch. A mathematical model which characterizes the change of corner of reflection of root crops after their hitting with the coil of screw depending on the parameters of process is built. On the basis of the conducted analysis of direction of motion of root crops or corner reflection of root crops after their co-operating with the coil of screw grounded basic limits of change structurally of kinematics parameters of purifier of lots of root crops.Item Розрахунок втрат тиску в об’ємних гідроприводах сільськогосподарських машин(КНТУ, 2011) Ковальчук, Н. В.; Мещишена, Л. Г.; Kovalchuk, N.; Meshishena, L.Запропонована програма розроблена для розрахунку втрат тиску в об’ємних гідроприводах, яка дозволить за мінімальний термін виконати розрахунки по декількох варіантах температурних показників, робочих рідин, гідроапаратури та обрати з них найбільш оптимальний. Suggested software is designed for multiple swift calculations of pressure losses in a hydraulic servo unit whilst operating with different liquids under variable temperature ranges. It allows selecting the best suitable hydraulic liquid and optimal servo unit operating temperature envelope.Item Алгоритм розрахунку розгалуженої мережі водопостачання(КНТУ, 2010) Ковальчук, Н. В.; Мещишена, Л. Г.; Kovalchuk, N.; Meshishena, L.Розроблена блок-схема розрахунку розгалуженої мережі водопостачання дозволяє за будь-якою програмою виконати багато варіантів цих розрахунків за короткий час, а також визначити оптимальні економічно-вигідні діаметри трудопроводів. Designed algorithm of agriculture water supply systems` hydraulic and cost-efficiency evaluation is an easy-touse approach for computer-assisted finding of the best values of water main network parameters.Item Передумови нормування мінливості вирівняності стеблостою льону-довгунцю(КНТУ, 2008) Лімонт, А. С.Досліджена мінливість висоти і діаметра стебел льону-довгунцю. Відшуканий кореляційний зв’язок між коефіцієнтами варіації вказаних характеристик рослин. The paper investigates the variability of fiber flax stem height and diameter. The correlation connction between the above characteristics variation coefficients has been found.Item Програма для визначення характеристики відцентрового насоса після обточки робочого колеса(КНТУ, 2012) Ковальчук, Н. В.; Kovalchuk, N.В статті представлена програма розрахунку діаметра обточеного робочого колеса відцентрового насоса при його регулюванні або підборі, що дає можливість в короткий термін не тільки визначити параметри його обточки, але і нові характеристики насоса, і координати точок спільної роботи насоса з трубопроводом. In the article the program of diameter calculation for turning driving wheel of centrifugal pump by regulation or selection is presented, it gives the opportunity to determine not only the parameters of turning, but new pump characteristics and points of coordinates for joint work of pump with conduit .