Збірники наукових праць ЦНТУ
Permanent URI for this communityhttps://dspace.kntu.kr.ua/handle/123456789/1
Browse
Search Results
Item Огляд впливу повзучості бетону на роботу попередньонапружених сталезалізобетонних конструкцій споруд цивільного захисту(ЦНТУ, 2023) Гасенко, А. В.; Дарієнко, В. В.; Бібік, М. В.; Бібік, Д. В.; Слонь, В. В.; Hasenkо, А.; Dariienko, V.; Bibik, М.; Bibik, D.; Slon, V.Реологічні властивості бетону в основному визначаються його властивостями повзучості. У випадку попереднього напруження сталезалізобетонної конструкції відбувається перерозподіл зусиль в її перерізі між сильно навантаженими і малонавантаженими елементами, а саме між сталевим армуванням і бетоном. У роботі проаналізовано загальні відомості про повзучість бетону та її вплив на втрати під час попереднього напруження, в тому числі із застосуванням сучасних програм скінченно-елементного моделювання, що дозволяють задавати фізичну нелінійність бетону і його реологічні властивості. The rheological properties of concrete are mainly determined by its creep properties, which affect the stress-strain state of the structure over time. In the case of pre-stressing a steel-reinforced concrete structure, forces are redistributed in its section between highly loaded and lightly loaded elements, namely between steel reinforcement and concrete. It should be noted that the supporting frame of buildings and structures (in addition to reliability, safe operation and economic feasibility) must guarantee functional suitability. It is impossible to determine the functional suitability of the structure without a correct prediction of the redistribution of stresses in time between the concrete and the reinforcement, which occurs as a result of the creep of concrete. According to the current norms of DBN B.2.6-98:2009 and EN (Eurocode 2), the criterion for the appearance of the limit state of reinforced concrete structures is the achievement of limit values by the deformations of compressed concrete. Therefore, a detailed study of the rheological properties of prestressed reinforced concrete is undoubtedly an urgent issue. The paper analyzes general information about the creep of concrete and its effect on losses during prestressing, including with the use of modern finite element modeling programs, which allow not only physically nonlinear characteristics of concrete to be specified when creating models of reinforced concrete structures, but also take into account the geometric nonlinearity of the work of composite reinforced concrete structure, but also to specify the rheological properties of concrete, in particular, creep characteristics.Item Експериментальні випробування попередньо напружених несучих елементів огороджувальних конструкцій з холодноформованих сталевих профілів на косий згин(ЦНТУ, 2023) Дроботя, О. В.; Drobotia, О.Несучими елементами легкого зовнішнього стінового огородження будівель слугують стінові прогони. Зовнішнім навантаженням на них є вертикальне навантаження від власної ваги стінового огородження та горизонтальне вітрове навантаження, що приблизно рівні між собою. Тому стінові прогони працюють на згин в двох площинах та їх необхідно проектувати рівноміцними в цих площинах. У роботі автором досліджено можливість застосування та доведена доцільність попереднього напруження в одній площині сталебетонних прогонів із зменшеною металоємністю саме в цій площині. Wall purlins serve as load-bearing elements of the light external wall girders of buildings. Structurally, such wall girders are horizontal beam elements. The external load on the wall girders is the vertical load from the own weight of the wall enclosure and the horizontal wind load. Thus, wall girders work for bending in two planes or the so-called oblique bending. The wide application of elements operating in conditions of oblique bending requires a comprehensive theoretical and experimental study of their operation. The load from the own weight of the wall enclosure, made of light sandwich panels, is approximately equal to the wind load on the territory of Ukraine. Therefore, in this case, the wall girders are designed with equal strength in two planes. To find out the real operation of obliquely bent elements, it is necessary to determine all the parameters that can affect the picture of the destruction of such elements. The purpose of the work is to study experimentally the possibility of applying pre-stressing in one plane of reinforced concrete girders with reduced metal capacity in this plane. The subject of the study is the stress-strain state and bearing capacity of a reinforced concrete rod prestressed in this way. The investigated steel-concrete girders were made of bent channel No. 10 with a wall thickness of 3 mm, the inner cavity of which was filled with concrete of class C20/25. Before concreting the inner cavity, a preliminary bending of the steel profile opposite to the operational one was carried out. The magnitude of the previous bending of the steel profile compensated for its reduced geometric characteristics in this plane. The use of a pre-stressed trough-shaped steel profile in the form of a bent channel No. 10 with a wall thickness of 3 mm for a wall run, followed by its concreting, allows you to reduce steel consumption by up to 38,5% compared to, for example, the use of an 80×3 mm pipe of the same bearing capacity for a run.