Збірники наукових праць ЦНТУ
Permanent URI for this communityhttps://dspace.kntu.kr.ua/handle/123456789/1
Browse
4 results
Search Results
Item Підвищення довговічності турбокомпресора в внаслідок ремонтного впливу(ЦНТУ, 2021) Кулєшков, Ю. В.; Черновол, М. І.; Красота, М. В.; Руденко, Т. В.; Солових, Є. К.; Осін, Р. А.; Kuleshkov, Yu.; Chernovol, M.; Rudenko, T.; Krasota, M.; Solovykh, Ye.; Osin, R.Для відновлення деталей машин можуть застосовуватися різноманітні способи відновлення і зміцнення. Однак далеко не всі способи можуть забезпечити необхідний ресурс для відновлення і зміцнення деталей, що працюють в абразивному та корозійному середовищі середовищах. Одним із сучасних напрямків підвищення зносостійкості та іншими властивостями відновлювальних покриттів є використання композиційних матеріалів. В цій статті представлені результати досліджень щодо розробки нового способу відновлення і зміцнення деталей композиційними матеріалами заснованими на використанні хімічного парофазного осадженням металів CVD - методу (Chemicikal Vapor Deposition) шляхом розкладання металоорганічних сполук. Показано, що розроблений композит матеріал, отриманий CVD – методом розкладання металоорганічних забезпечує підвищення зносостійкості не менше ніж в 2,0…2,2 раз в порівняні з новими деталями. A turbocharger is a unit of modern internal combustion engines designed to boost it. Since a drive of the turbocharger is most often carried out from the energy of the exhaust gases, the conditions of its operation can not be called favorable: the temperature of the exhaust gases sometimes reaches 7000C, high chemical activity of the exhaust gases, high speed of rotation of the turbine. The consequence of difficult operating conditions is the wear of its elements. One of the main causes of wear of the active elements of the turbocharger is abrasive wear. Various methods of restoration and strengthening can be used to restore machine parts. However, not all methods can provide the necessary resource for the restoration and strengthening of parts working in abrasive and corrosive environments. One of the modern directions of increasing the wear resistance and other properties of reducing coatings is the use of composite materials. This article presents the results of research on the development of a new method for restoring and strengthening parts with composite materials based on the use of chemical vapor deposition of metals CVD - method (Chemicikal Vapor Deposition) by decomposition of organometallic compounds. It is shown that the developed composite material obtained by the CVD-method of decomposition of organometallic compounds provides an increase in wear resistance of at least 2.0...2.2 times in comparison with new parts composite material. Vapor-phase deposition of metals, Chemicikal Vapor Deposition-method, decomposition of organometallic compounds.Item Получение и исследование восстановительных покрытий на деталях машин с использованием механокомпозитов, содержащих TiCиTiB2(ЦНТУ, 2017) Лузан, С. А.; Сидашенко, А. И.; Лузан, А. С.; Лузан, С. О.; Сідашенко, О. І.; Лузан, А. С.; Luzan, S.; Sidashenko, О.; Luzan, А.В статье описано исследование восстановительных износостойких покрытий для деталей сельскохозяйственных машин с использованием композиционных материалов, представляющих собой смесь матричного материала и механокомпозита, полученного с применением СВС-процесса. В результате разработан композиционный материал на основе самофлюсующегося сплава системы Ni-Cr-B-Si, модифицированный механокомпозитом, содержащим карбид и диборид титана. У статті описано дослідження відновлювальних зносостійких покриттів для деталей сільськогосподарських машин з використанням композиційних матеріалів, що представляють собою суміш матричного матеріалу і механокомпозиту, отриманого з застосуванням СВС-процесу. В результаті розроблений композиційний матеріал на основі самофлюсуючого сплаву системи Ni-Cr-B-Si, модифікований механокомпозитом, що містить карбід і диборид титану. The article describes the study of restorative wear-resistant coatings for agricultural parts using composite materials, which are a mixture of matrix material and mechanocomposite obtained using the SHS process. As a result, a composite material based on a self-fluxing Ni-Cr-B-Si alloy modified with a mechanocomposite containing carbide and titanium diboride was developed. The microstructure of surfaced coatings is the matrix material, which is the granulated powder 10 grinded cladding powder 01 alloy, in which solid inclusions are uniformly distributed, presumably, these are titanium diboride (TiB2), iron carbide (Fe3C) particles.Item Дослідження зносостійкості відновлювальних покриттів системи Ni-Cr-B-Si, модифікованих механоактивованими СВС-матеріалами(ЦНТУ, 2017) Сідашенко, О. І.; Лузан, А. С.; Сидашенко, А. И.; Sidashenko, O.; Luzan, A.В статті описано дослідження ресурсозберігальної технології відновлення робочих органів сільськогосподарських машин, схильних до абразивного зносу в процесі експлуатації. Для відновлення методом електродугової наплавки запропонований композиційний матеріал на основі порошкового матеріалу системи Ni-Cr-B-Si, модифікований механоактивованим матеріалом, отриманим із застосуванням СВС-процесу. Результати дослідження показали, що зносостійкість розробленого копозиційного матеріалу перевищує зносостійкість наплавленого шару порошком марки ПГ-10Н-01 в 2 рази, що дозволяє рекомендувати його для збільшення ресурсу відновлених робочих органів сільськогосподарських машин. В статье описано исследование ресурсосберегающей технологии восстановления рабочих органов сельскохозяйственных машин, подверженных абразивному износу в процессе эксплуатации. Для восстановления методом электродуговой наплавки предложен композиционный материал на основе порошкового материала системы Ni-Cr-B-Si, модифицированный механоактивированным материалом, полученным с применением СВС-процесса. Результаты исследования показали, что износостойкость разработанного копозиционного материала превышает износостойкость наплавленного слоя порошком марки ПГ-10Н-01 в 2 раза, что позволяет рекомендовать его для увеличения ресурса восстановленных рабочих органов сельскохозяйственных машин. The article describes the research of resource-saving technology restoration working organs of agricultural machines, subject to abrasive wear during operation. A composite material based on the Ni-Cr-B-Si powder material modified with mechanically activated material obtained using the SHS process is proposed for restoration by electric arc welding. The results of the research showed that the wear resistance of the developed composite material exceeds the wear resistance of the weld layer by the PG-10N-01 powder by a factor of 2, which allows recommending it for increasing the life of the restored working organs of agricultural machines.Item Комп'ютерне моделювання полів температур та напружень в композиційних матеріалах та покриттях при їх формуванні, терті та зношуванні(КНТУ, 2014) Аулін, В. В.; Бобрицький, В. М.; Aulin, Viktor; Bobrytskyi, VitaliiВ статті за допомогою комп’ютерного моделювання досліджено поле температур та напружено- деформований стан композиційних матеріалів та покриттів на всіх етапах їх життєвого циклу. Визначено розподіл нестаціонарних полів температур та напружень, які виникають в композиційних матеріалах та покриттях в процесі їх формування і тертя та зношування, а також локальні області з максимальною різницею перепаду температур і напружень та вплив на них внутрішніх і зовнішніх факторів. Виявлено тісний взаємозв'язок між складом композиційних матеріалів і покриттів, розмірами і формою їх структурних складових та статистичними і локальними значеннями досліджуваних полів температур і напружень відповідних нестаціонарних полів. Результати комп’ютерного моделювання дають можливість оптимізувати склад та структуру композиційних матеріалів та покриттів для підвищення їх фізико-механічних та триботехнічних характеристик і властивостей. The article by computer simulation investigated the distribution of temperature and stress-strain state of composite materials and coatings at all stages of their life cycle. Determined the distribution of transient temperature fields, stresses and strains that occur in composite materials and coatings in the process of forming and friction and wear , as well as local areas with a maximum difference of temperature and stress and the impact on their internal and external factors. Computer simulation of composite materials and composite coatings made it possible to construct a non-stationary heat field and thermal stress field in composite materials and composite coatings with dispersion - strengthened and eutectic types of structures that arise from stationary sources of heat ( of friction ). It is shown that the configuration of these fields are essentially uniform, there are significant changes in temperature and stress due to heterogeneity of structure heterogeneity thermophysical and mechanical properties of the structural components of composite materials and composite coatings that achieve , depending on the load of friction , melting components, and local stress - up to several GPa. The value of tensile stress and compressive alternating throughout the volume of the composite material and composite coatings. There is a close relationship between the structure of composite materials and composite coatings, the size and shape of structural components and statistical and local values of temperature and stress appropriate nonstationary fields. To minimize temperature changes and thermal stresses to use uniform size structure of the filler with a maximum dispersion of carbides and align the thermal properties of filler and matrix, which must provide high relaxation ability. According to the results of computer simulation can optimize the composition and structure of composite materials and coatings to enhance their physical and mechanical characteristics and tribotechnical.