Збірники наукових праць ЦНТУ
Permanent URI for this communityhttps://dspace.kntu.kr.ua/handle/123456789/1
Browse
2 results
Search Results
Item Формозміна пустотілих поковок по типу гільз у процесі протяжки без оправки бійками зі скосами(ЦНТУ, 2025) Марков, О. Є.; Музикін, Є. С.; Музикін, П. С.; Markov, O.; Muzykin, Ye.; Muzykin, P.У статті розроблено новий техпроцес деформування поковок по типу довгих гільз ромбічними бойками з ухилами. Вивчення процесу деформування дозволило з’ясувати закономірності формозмінення пустотілої заготовки для нового технологічного процесу. Досліджувалися кути вирізів та ухилів бойків (10°, 20° і 30°) і довжина подачі заготовки у бойки. При подачах, що дорівнюють 0,1D та куті вирізу ромбічних бойків в 115° проходить мінімальне закриття отвору пустотілої заготовки. Ефективною геометрією деформуючого інструменту для збільшення коефіцієнту витяжки при деформуванні пустотілих гільз слід використовувати ромбічні бойки з ухилом скосів 10...20° і довжиною подачі заготовки b/D=0,1. Кривізна торця отвору дорівнює припуску на мехобробку, що забезпечує отримання потрібних розмірів і форми поковки без використання оправки. The purpose of the work is to increase the efficiency of the processes of deformation of hollow cylindrical blanks without a mandrel by means of scientifically substantiated design of their deformation modes based on the created numerical models, which allow developing and evaluating a new technological process for the deformation of such forgings. The new technological process of deformation will increase the competitiveness of domestic products, which will allow increasing the volume of exports of unique products on the foreign market. The article develops a new technological process for the deformation of forgings of the type of long sleeves with rhombic strikers with slopes. The study of the deformation process made it possible to clarify the regularities of the shape change of the hollow blank for the new technological process. The angles of the cutouts and slopes of the strikers (10°, 20° and 30°) and the length of the workpiece feed into the strikers were studied. At feeds equal to 0.1D and a cut angle of rhombic punches of 115°, the minimum closing of the hole of the hollow workpiece takes place. The effective geometry of the deforming tool to increase the extraction coefficient when deforming hollow sleeves should be rhombic punches with a bevel slope of 10...20° and a feed length of the workpiece b/D=0.1 etc.Item Оптимізація технології холодного об’ємного штампування накидних гайок рукавів високого тиску(КНТУ, 2013) Кришкін, Б. Б.; Kryshkin, B.У статті описано методику моніторингу та оптимізації конструктивних параметрів робочих деталей штампу для холодного об’ємного штампування деталі «Гайка накидна» із візуалізацією отриманих результатів за допомогою програмного комплексу DEFORM 3D. The work purpose - research of cold forging technology of high pressure sleeves cap nuts. In the article methodology of determination of tensions and efforts is described in the working details of instrument for the multiposition cold by volume stamping of detail «cap nut» sleeves high-pressure with the use of programmatic complex DEFORM 3D, because of what the sequence of realization of optimization of the tensely-deformed state of puncheons and matrices is offered before their planning. It is established that use of the program DEFORM 3D complex allows to carry out an exact assessment intense the deformed condition of the tool at multitransitional cold forging.