Збірники наукових праць ЦНТУ
Permanent URI for this communityhttps://dspace.kntu.kr.ua/handle/123456789/1
Browse
3 results
Search Results
Item Дослідження впливу схеми розташування ножів котка-подрібнювача на показники якості подрібнення стебел соняшнику(ЦНТУ, 2021) Шейченко, В. О.; Черновол, М. І.; Вольський, В. А.; Коцюбанський, Р. В.; Sheichenko, V.; Chernovol, M.; Volskyi, V.; Kotsiubanskyi, R.Роботу присвячено удосконаленню технологічного процесу подрібнення стебел соняшнику завдяки дослідженню впливу схеми розташування ножів котка-подрібнювача на показники якості подрібнення. Розроблено та виготовлено дослідний зразок котка-подріюнювача, ріжучі ножі у якого розміщено по всій ширині захвату у шаховому порядку з можливістю змінювати кут нахилу до осі обертання барабана в діапазоні 5…20°. Дoслiджено вплив рoзтaшування рiжучoї крoмки пoдрiбнюючoго нoжa кoтка нa пoказники якocті викoнання опeрацiй пoдрібнeння і зaгортaння стeбeл coняшнику. The study of the arrangement of the blades of the roller-grinder on the quality of grinding. It is The work is devoted to the improvement of the technological process of grinding sunflower stalks due to the study of the influence of the arrangement of the blades of the roller-grinder on the quality of grinding. in the range of 5… 20 °. It is noted that under 800 kg by loading the roller with the right location of the chopping knives, the lowest value of mathematical expectations of the distribution of crushed stem particles is set at 18.6 km / h. This value is 14%, 30%, 40% and 20% less than the speed , respectively, 7.45 km/h, 10.08, 13.6, 22 km/h. Exceedance of values of mathematical expectations of distributions of particles of stalks at a roller-shredder with the left scheme of an arrangement of knives over the right, for loading of 800 kg, at all speeds investigated is established. The lowest value of mathematical expectation for the right layout of the knives was set at a speed of 18.6 km / h, and for the left - at a speed of 13.6 km / h. The highest value of the mathematical expectation of the distribution of parts of sunflower stalks at the left location of the knives is set at a speed of 10.08 km/h, and for the right scheme - at a speed of 13.6 km/h. Exceeding the lowest value of mathematical expectation over the highest within one scheme of placement of knives was - on the left 48%, on the right 41%. In the roller with the left location of the cutting edge of the knives, with a load of 600 kg in the range of 51–100 mm, the percentage of crushed particles of sunflower stalks exceeded the corresponding values with a load of 800 kg. At speeds of 10.08 km/h, 13.6, 18.6 and 22 km/h, this excess was 1.9 times, 1.44, 1.96 and 1.99 times, respectively.Item Вплив рослинних решток на інтенсивність абразивного зношування робочих органів ґрунтообробних машин(ЦНТУ, 2020) Борак, К. В.; Borak, K.Абразивний знос один з найпоширеніших видів зношування, на його долю припадає до 50% всіх відмов деталей машин. Дослідження закономірностей процесу абразивного зношування є безумовно актуальною задачею. В роботі розглянуто вплив хімічного фактору, а саме наявність рослинних решток в абразивній масі, на інтенсивність зношування робочих органів ґрунтообробних машин. Лабораторні дослідження проводили за методом «крильчатки», а експлуатаційні – на універсальному дисковому агрегаті УДА 4,5 в умовах Овруцького району Житомирської області (ґрунти супіщані). В результаті проведення досліджень з’ясовано, що при виділені соків (патоки) підвищується інтенсивність абразивного зношування в лабораторних умовах на 13,5…21,5%, а в експлуатаційних умовах – на 8%. Абразивне зношування робочих органів ґрунтообробних машин є доволі складним процесом і не може розглядатися тільки механічної точки зору. Abrasive wear is one of the most common types of wear accounting for up to 50% of all failures of machine parts. The study of laws governing the process of abrasive wear process is undoubtedly a critical task. The paper is dedicated to the effect that the chemical factor, in particular the presence of plant remains in the abrasive mass, has on the tilling machine movable operating parts abrasive wear rate. Laboratory researches were performed with the Impeller technique, while the field tests – with a multipurpose disk tiller UDA-4.5 in the conditions of the Ovruch district of Zhytomyr region (sandy loam soil). As follows from the study, the ooze of the sap (syrup) leads to an increase of the abrasive wear rate by 13,5…21,5% in the laboratory conditions. As a result, it was found that the rate of mass wear of the disk working bodies (multipurpose disk tiller UDA-4.5) on the field after corn was increased by 8% compared to the rate of wear of the disk working bodies on the field without plant residues. Results of the field tests confirm those of the laboratory studies, although the latter have demonstrated an increase in the wear rate, which is by 13,5% greater than got upon the field tests. Such a deviation is conditioned by a higher concentration of the corn crop remains in the abrasive mass during laboratory testing. Abrasive wear of the tilling machine movable operating parts may not be identified as a simple mechanical process, as the working surface wear rate may be significantly increased by the chemical factor when subject to wear in the real soil. Абразивный износ один из самых распространенных видов износа, на его долю приходится до 50% всех отказов деталей машин. Исследование закономерностей процесса абразивного износа является, актуальной задачей. В работе рассмотрено влияние химического фактора, а именно наличие растительных остатков в абразивной массе, на интенсивность износа рабочих органов почвообрабатывающих машин. Лабораторные исследования проводили по методу «крыльчатки», а эксплуатационные – на универсальном дисковом агрегате УДА 4,5 в условиях Овруцкого района Житомирской области (почвы супесчаные). В результате проведения исследований установлено, что при выделении соков (патоки) повышается интенсивность абразивного износа в лабораторных условиях на 13,5...21,5%, а в эксплуатационных условиях – на 8%. Абразивный износ рабочих органов почвообрабатывающих машин это очень сложный процесс и не может рассматриваться только механической точки зрения.Item Перспективні напрямки вдосконалення конструкцій технічних засобів для подрібнення рослинних решток(КНТУ, 2016) Богатирьов, Д. В.; Сало, В. М.; Кислун, О. А.; Bohatyrov, Dmitriy; Salo, Vasyl; Kuslyn, OlegНаведений напрям розробки та вдосконалення сільськогосподарських машин для подрібнення рослинних решток в Україні є новим та дуже актуальним. Представлено аналіз результатів польових випробовувань двох типів подрібнювачів рослинних решток вітчизняного виробництва. Основним показником роботи даного типу машин обрано співвідношення розмірів решток стебел після подрібнення в залежності від використання граблин. Одним із способів підвищення якості подрібнення є встановлення додаткового пасивного робочого органу - граблини, для орієнтації стебел перпендикулярно лезам ножів робочих органів подрібнювачів. Наведені результати випробовувань свідчать про доцільність використання граблин для даного типу сільськогосподарської техніки. Worldwide production trend of environmentally friendly crop production leads to the search for new technologies for growing crops and developing the necessary technology. The need for fertilizers feed plants are always topical issue, but man-made pollution fertilizers fertile soil affects the quality of agricultural products, which can lead to increased morbidity. The widespread use of pesticides has created specific problems related to the acquisition of weeds, pests and pathogens resistance to them. Our country is not enough attention paid to the established type of agricultural machinery, whose work would be aimed at improving topsoil naturally, that is - the creation of the ground layer of crushed plant residues with partial wrapping them. Such a layer of crushed stems (plant residues) will naturally maintain soil micro flora and will not only maintain but also increase over time humus content. Reproduced the direction of development and improving agricultural machines for crushing plant in Ukraine remains a new and very important. The analysis of the results of field tests of two types Choppers residues domestic production. The main indicator of the type of machines chosen aspect ratio remains after crushing the stems, depending on the use of guides. One way to improve the quality of grinding is an extra passive working body - guides for orientation stems perpendicular edges of working blades shredder. The results of the tests show the feasibility of using guides for this type of agricultural machinery. One way of improving your grinding plant residues can be input to the famous design of additional working machines. However, providing high efficiency of their work requires theoretical justification of rational design and process parameters.