Збірники наукових праць ЦНТУ
Permanent URI for this communityhttps://dspace.kntu.kr.ua/handle/123456789/1
Browse
2 results
Search Results
Item Surface Topography of Arc-Sprayed Coatings by Cored Wires of Different Compositions and Its Influence on the Wear Mechanism(ЦНТУ, 2025) Hvozdetskyi, V.; Lukyanenko, A.; Markovych, S.; Student, M.; Zadorozhna, Kh.; Mozola, N.; Гвоздецький, В. М.; Лук`яненко, О. Г.; Маркович, С. І.; Студент, М. М.; Задорожна, Х. Р.; Моцола, Н. З.The purpose of this work is to study the influence of the components of the composition of powder wires on the surface characteristics of sanded electric arc coatings. For the application of coatings used electric spray and powder wires with a diameter of 1.8 mm containing powders FeSi, FeTi, FeMn, pure metals Al and Cr and carbide B4C with a filling factor reached 24%. Spray parameters: current – 150 A, voltage – 32 V, air stream pressure – 0.6 MPa, spray distance – 120 mm. The surface topography revealed the plate structure of the coating with slats of different chemical composition. In coating are presence of carbides and borides, a significant amount of iron oxides and oxides of alloyed elements at the slats. Provisions from a considerable height contribute to intense wear due to reducing the friction steam surface. The interaction is regulated by the ratio of the depth of the projections (H) to the radius of its sharp tip (r). When H/r <0.02, there is only elastic interaction, with the material of counteraction elastic. In the range of 0.02 < H/r <0.7, the projections induce plastic deformation of the counter-body. If H/r > 0.7, sharp projections are cut to the surface, generating micro -cutting. Reducing the number and size of inclusions and increasing their rounding radii are critical for improving wear resistance etc. Робота присвячена дослідженню впливу компонентів складу порошкових дротів на поверхневі характеристики відшліфованих електродугових покриттів. Для нанесення покриттів застосовувався електродуговий розпилювач та порошкові дроти діаметром 1,8 мм, що містять порошки FеSі, FеTі, FеMn, чисті метали Al і Cr та карбід B4C з коефіцієнтом наповнення досяг 24%. Параметри розпилення: струм – 150 А, напруга – 32 В, тиск повітряного струменя – 0,6 МПа, відстань розпилення – 120 мм. Топографія поверхні виявила пластинчасту структуру покриття з ламелями різного хімічного складу і мікротвердості, наявність карбідів та боридів, значну кількість оксидів заліза та оксидів легованих елементів на межах ламелей. Виступи з значної висоти сприяють інтенсивному зносу через зменшення поверхні пари тертя тощо.Item Розмірна обробка електричною дугою ступінчастих стержнів(КНТУ, 2015) Шмельов, В. М.; Shmelyov, VitaliyЗапропоновано технологію виготовлення ступінчастих стержнів розмірною обробкою електричною дугою (РОД). Визначено вплив технологічних характеристик на показники процесу РОД. Отримані математичні моделі продуктивності процесу РОД ступінчастих стержнів, бічного міжелектродного зазору (МЕЗ), відносного лінійного зносу електрод-інструменту (ЕІ), шорсткості бічної поверхні стержня, відносної шорсткості торцевої поверхні стержнів. The paper purpose - the development of manufacturing techniques step rods of dimensional processing the electric arc. In a paper the analyzes the impact of the technical characteristics on process of dimensional processing the electric arc on its index. Identified the main factors influencing the performance of dimensional processing the electric arc. The received mathematical models of productivity of the manufacturing process of step rods, side-electrode gap, the relative linear wear of the electrode-tool, the roughness of the side surface of the rod, the relative roughness of the end surface of the rod. Using the method of dimensional processing the electric arc step rods allow their manufacture with high productivity and quality of the treated surface.