Конструювання, виробництво та експлуатація сільськогосподарських машин. Загальнодержавний міжвідомчий науково-технічний збірник.
Permanent URI for this communityhttps://dspace.kntu.kr.ua/handle/123456789/19
Ідентифікатор медіа: R30-03925 (рішення Національної ради України від 25.04.2024 р. № 1418).
Мови видання: українська, російська, англійська, періодичність - один раз на рік.
Browse
9 results
Search Results
Item type:Item, Зміна шорсткості поверхні при нанесенні антифрикційних покриттів(ЦНТУ, 2022) Шепеленко, І. В.; Кириченко, А. М.; Магопець, С. О.; Красота, М. В.; Василенко, І. Ф.; Shepelenko, І.; Kyrychenko, А.; Mahopets, S.; Krasota, М.; Vasylenko, І.В роботі розглянуто шорсткість поверхні антифрикційного покриття як основний критерій оцінки якості отриманого покриття. Експериментальні дослідження нанесення антифрикційного покриття фрикційно-механічним методом виконувалися за розробленою методикою на зразках із сірого чавуну СЧ20. В якості матеріалу антифрикційного покриття використано латунь Л63. Встановлені основні закономірності зміни шорсткості поверхневого шару в залежності від параметрів процесу фінішної антифрикційної безабразивної обробки (ФАБО). Отримані дані дозволяють прогнозувати та керувати в процесі ФАБО таким важливим геометричним параметром поверхневого шару, як шорсткість, а отже, підвищити якість отриманого покриття. The analysis of literary sources made it possible to state that the surface roughness obtained by the finish anti-friction non-abrasive treatment (FANT) is one of the main quality criteria of the anti-friction coating and largely determines the process of running-in during the initial period of operation. The purpose of the presented research is to establish the main patterns of changes in the roughness of the surface layer treated by FANT. Application of anti-friction coatings was carried out according to the method developed by the authors using the original device on a vertical milling machine. Special disc-shaped samples made of gray cast iron SCH20 were used as the tested samples. L63 brass was used as the material of the anti-friction coating. Among the technological factors that changed with the selected FANT scheme, the following were selected: the pressure force of the anti-friction bar and the number of rubbing passes. The roughness of the surface was estimated by the average arithmetic deviation of the Rа profile. The average value obtained as a result of three measurements was taken as the value of the roughness parameter Rа. The obtained values made it possible to establish the main patterns of changes in the roughness parameter depending on the technological parameters of FANT. It is shown that with an increase in the initial surface roughness parameter Rа, the value of the change in the average arithmetic deviation of the profile Ra also increases. High initial values of the arithmetic average deviation of the Ra profile do not allow obtaining a continuous, and therefore high-quality anti-friction coating of FANT. Obtaining a high-quality anti-friction coating with the selected FANT scheme became possible with the following processing modes: pressing force of the anti-friction bar P = 164.6 N; the number of rubbing cycles is N = 6. The results of the studies performed on the application of FANT anti-friction coatings make it possible to predict and control such an important geometric parameter of the surface layer as roughness, which largely determines the quality of the treated surface.Item type:Item, Вплив технологічних параметрів процесу розмірної обробки електричною дугою на шорсткість робочої поверхні спряжених пар робочих деталей розділових штампів(КНТУ, 2009) Носуленко, В. І.; Шмельов, В. М.; Nosulenko, V.; Shmelyov, V.В статті описано вплив технологічних параметрів процесу РОД: сили технологічного струму /, що змінюють в межах від 100А до 400А; статичного тиску робочої рідини Ps, що змінюють в межах від ІМПа до 1,4МПа; висоти робочого пояска графітового електрод-інструмента h, що змінюють в межах від 0,5мм до 1,5мм, на шорсткість робочих поверхонь робочих деталей розділових штампів Ra, та доведено можливість застосування способу РОД в сукупності з СКЗ ЕІ для виготовлення спряжених пар робочих деталей розділових штампів. In article influence of technological parametres of process of dimensional processing by an electric arch is described: forces of a technological current /, changing in limits from 100A to 400A; static pressure of the working liquid Ps, changing in limits from IMPa to l,4MPa; heights of a working belt of the graphite electrodetool h, changing in limits from 0,5mm to 1,5mm, on a roughness of working surfaces of working details of dividing stamps Ra, also possibility of application of a way of dimensional processing by an electric arch in aggregate in the way of operated deterioration an electrode-tool for manufacturing of conjugating pairs working details of dividing stamps is proved.Item type:Item, Дослідження мікрогеометрії поверхонь тертя деталей фрактальним методом(КНТУ, 2009) Аулін, В. В.; Лізунов, С. М.; Aulin, V.; Lizunov, S.В статті мікрогеометрію поверхонь деталей, зміцнених та модифікованих сучасними технологіями, запропоновано досліджувати за допомогою фракталів. Показано, що механічні і сучасні методи обробки робочої поверхні деталей створюють принципово різні елементи топографії. In clause microgeometry of a surface of details, hardening and the updating by modem technologies, is offered to investigate with the help fractals. Is shown, that the mechanical and modem methods of processing of a working surface of details form essentially different elements of topography.Item type:Item, Виробничі технології як альтернатива обкатування деталей ДВЗ(КНТУ, 2013) Ошовський, В. Я.; Oshovsky, ViktorРозглядаються технології обробки в умовах виробництва як альтернатива обкатування для підвищення ресурсу деталей двигуна внутрішнього згоряння (ДВЗ). Проаналізовано недоліки обкатування та запропоновано метод збільшення ресурсу рухомих спряжень. Доведена можливість збільшення ресурсу рухомих спряжень ДВЗ притиранням і шаржуванням алмазними пастами.Technologies of treatment in the conditions of production are examined as an alternative to rolling for the increase of details resource of internal-combustion engine (ICE). The lacks of rolling-off are analysed and the method of increasing the resource of mobile interfaces is offered. Possibility of the increasing of resource of mobile interfaces by the ICE grinding and caricaturing by diamond pastes is proved.Item type:Item, Оптимізація якісних характеристик поверхонь робочих деталей розділових штампів в умовах розмірної обробки електричною дугою(КНТУ, 2014) Шмельов, В. М.; Shmelyov, V.Виконано оптимізацію якісних характеристик поверхонь робочих деталей розділових штампів в умовах розмірної обробки електричною дугою (РОД). Показано залежність між конструкцією матриці і необхідною шорсткістю її робочої поверхні. Описано залежності якості обробленої поверхні робочих деталей розділових штампів від технологічних характеристик процесу РОД. The paper purpose-optimisation of qualitative performances of a surface of working details dividing ofstamps in the conditions of dimensional processing the electric arc. In a paper the analyzes of a construction of the matrix and a necessary surface roughness of working details of separating dies is carried out, on the basis of this gives recommended roughnesses of surfaces of working details received by methods of a classical electrical discharge machining. On the basis of experimental data derived the mathematical model of a surface roughness of working details dividing of stamps depending on the basic technical characteristics on process of dimensional processing the electric arc. It is shown that the surface roughness of working details dividing of stamps received by a mode of dimensional processing the electric arc, corresponds to the recommended surface roughness of these details received by classical methods of an electroerosion machining. Use of a mode of dimensional handling by an electric arc allows to receive working details of separating dies of the necessary sizes and with necessary indexes of a surface roughness of the worker of a part, and accordingly and to ensure necessary firmness, and lowering of the cost price of their manufacture. Using the method of dimensional processing the electric arc allows to receive of working details dividing of stamps the necessary sizes and with necessary indexes of a surface roughness of the worker of a part, and according to ensure necessary firmness, and lowering of the cost price of their manufacture.Item type:Item, Шляхи зниження втрат робочої рідини у гідросистемах при експлуатації сільськогосподарських машин(КНТУ, 2011) Посвятенко, Е. К.; Будяк, Р. В.; Posviatenko, E.; Budiak, R.В статті визначено напрямки зниження втрат робочої рідини в гідросистемах сільськогосподарських машин шляхом підвищення якості поверхні глибоких отворів гільз циліндрів технологічними методами. Описано ресурсозберігальний процес обробки глибоких отворів за схемою «наскрізне деформуюче протягування – різальне протягування – розкочування роликовим інструментом». Подано принципи розробки комбінованого протяжного інструменту. Наведено геометричні та фізико-механічні характеристики поверхні та поверхневого шару отвору гільз. In article directions of decrease in losses of a working liquid in hydrosystems of agricultural cars at the expense of improvement of quality of surfaces of deep apertures of sleeves of cylinders by technological methods are defined. It is described resource-saving process of machining of deep apertures under the scheme «through deforming pulling - cutting pulling - rolling by the roller tool». Principles of creation of the combined lingering tool, geometrical and physicomechanical characteristics of a surface and a blanket of apertures of sleeves are resulted.Item type:Item, Дослідження взаємодії деформуючого елемента протяжки із оброблюваною поверхнею деталей із графітовмісних чавунів(КНТУ, 2014) Єрьомін, П. М.; Чернявський, О. В.; Студенець, С. Ф.; Eryomin, Р.; Chernyavskiy, А.; Studenets, S.Із застосуванням верстатного та допоміжного обладнання розроблена оригінальна методика дослідження впливу деформуючого протягування на стан обробленої поверхні. Результати дослідження дозволять розробити високоефективні конструкції деформуюче-ріжучих протяжок для обробки отворів в деталях із графітовмісних чавунів. An original technique to study the influence of deforming broaching on the condition of the treated surface. The purpose of the study - the impact on the state of the deforming broaching machined surface of the samples with a graphite cast irons. The possibility to reach the peeling of the surface layer details from cast iron during processing deforming broaching, and the required number of cycles of deformation is much smaller than for the processing of carbon steel. Results of the study will help to develop a highly efficient design deforming - cutting broaches for holes in the details of the graphite cast irons.Item type:Item, Проектування інструменту для різних методів обробки пластично-поверхневим деформуванням(КНТУ, 2010) Мажейка, О. Й.; Mazheyka, А.Запропонована методика проектування інструменту для обробки ППД. Приведені методи обробки та можливі схеми їх реалізації. Визначені основні чинники, що впливають на параметри інструменту. A design technique instrument is offered for treatment of PPD. The methods of treatment and possible charts of their realization are resulted. Basic factors, influencing on the parameters of instrument are certain the choice of proper material is offered for an instrument, developed flow-chart of algorithm of planning of instrument for PPD.Item type:Item, Технологічні характеристики процесу поділу пруткового металу на мірні заготовки способом розмірної обробки електричною дугою(КНТУ, 2010) Носуленко, В. І.; Великий, П. М.; Гаращенко, Ю. М.; Nosulenko, V.; Velikiy, P.; Garashenko, Y.Описано технологічні характеристики процесу поділу пруткового металу на мірні заготовки способом розмірної обробки електричною дугою тонкостінним видовженим пластинчатої форми електродом-інструментом, зокрема продуктивність, шорсткість обробленої поверхні і знос електрода-інструмента. Визначено вплив змінних факторів, таких як сила струму, статичний тиск рідини і робоча напруга, на продуктивність процесу, шорсткість обробленої поверхні, знос електрода-інструмента, та визначено основні керуючі фактори. Побудовано математичні моделі та графіки залежності технологічних характеристик від основних керуючих факторів, якими є сила струму І та статичний тиск рідини Ps. Technological descriptions of process of division metal of small twig are described on the measured purveyances by the method of dimensional arc treatment thin-walled extended plate form by an electrodeinstrument, in particular the productivity, roughness of the treated surface and tearing down of electrodeinstrument. Certainly poured in variable factors, such as strength of current, static pressure of liquid and working tension, on the productivity of process, roughness of the treated surface, tearing down of electrode-instrument, and certainly basic managing factors. Mathematical models and graphic arts dependence of technological descriptions from basic managing factors, which strength of current I and static pressure of liquid of Ps, are built.