Конструювання, виробництво та експлуатація сільськогосподарських машин. Загальнодержавний міжвідомчий науково-технічний збірник.
Permanent URI for this communityhttps://dspace.kntu.kr.ua/handle/123456789/19
Ідентифікатор медіа: R30-03925 (рішення Національної ради України від 25.04.2024 р. № 1418).
Мови видання: українська, російська, англійська, періодичність - один раз на рік.
Browse
4 results
Search Results
Item type:Item, Обробка розмірною електричною дугою шестигранних порожнин пуансонів гарячого пресування(КНТУ, 2016) Сіса, О. Ф.; Sisa, О.Виконано обґрунтування технологічної схеми формоутворення поверхонь шестигранної порожнини пуансонів гарячого пресування головок болтів, способом розмірної обробки електричною дугою з урахуванням особливостей фізичних механізмів їх утворення та гідродинамічних явищ в міжелектродному проміжку. Встановлені аналітичні зв’язки технологічних характеристик процесу розмірної обробки електричною дугою сталі 5ХНМ з режимами обробки і геометричними параметрами. The article is dedicated to the development of technology and accessories of the method for processing of hexagonal cavities of hot-pressing punches by electrical arc, as high-performance alternative to traditional processing methods. An important factor in increasing the carrying capacity of heavy duty bolts is the increasing of the elasticity of the bolt head. This condition is fully met by the high-strength bolts with hexagon head produced by the method of hot pressing. The use of an elastic flange ensures continuous operation under alternating loadings without loss of pre-tightening efforts. When developing equipment and tools, it is necessary to take into account the conditions which ensure the formation of the bolt head. The most important parameter for pressing is the dimensional accuracy, hot impact resistance of the tool, material ductility, burr tool cavity walls, since the pressure force on the transmission side surface is proportional to the pressure in the longitudinal direction. It is found that the optimum parameters hex hot pressing punch cavity walls during the processing performance of M = 610 mm³ / min. by electrical arc, is the roughness Ra = 2,5..6,3 mkm that provides frictional force required to fill the cavity of the bolt head. It is suggested to get the hexagonal cavities of hot pressing punches by dimension electrical arc with the set roughness Ra = 2,5..6,3 mkm of side walls, which allows you to take great allowances material at the lowest cost to the processing time. At the same time the cycle of processing is decreased 2-4,5 times. The objectivation of technological scheme of formation of hexagonal cavities of hot pressing punches by dimension electrical arc was made taking into account features of the physical mechanism of formation and hydrodynamic phenomena in the electrode gap. The analytical processing characteristics of process of sizing by electric arc of steel 5HNM with treatment regimes and geometrical parameters were established.Item type:Item, Вплив технологічних параметрів процесу розмірної обробки електричною дугою на шорсткість робочої поверхні спряжених пар робочих деталей розділових штампів(КНТУ, 2009) Носуленко, В. І.; Шмельов, В. М.; Nosulenko, V.; Shmelyov, V.В статті описано вплив технологічних параметрів процесу РОД: сили технологічного струму /, що змінюють в межах від 100А до 400А; статичного тиску робочої рідини Ps, що змінюють в межах від ІМПа до 1,4МПа; висоти робочого пояска графітового електрод-інструмента h, що змінюють в межах від 0,5мм до 1,5мм, на шорсткість робочих поверхонь робочих деталей розділових штампів Ra, та доведено можливість застосування способу РОД в сукупності з СКЗ ЕІ для виготовлення спряжених пар робочих деталей розділових штампів. In article influence of technological parametres of process of dimensional processing by an electric arch is described: forces of a technological current /, changing in limits from 100A to 400A; static pressure of the working liquid Ps, changing in limits from IMPa to l,4MPa; heights of a working belt of the graphite electrodetool h, changing in limits from 0,5mm to 1,5mm, on a roughness of working surfaces of working details of dividing stamps Ra, also possibility of application of a way of dimensional processing by an electric arch in aggregate in the way of operated deterioration an electrode-tool for manufacturing of conjugating pairs working details of dividing stamps is proved.Item type:Item, Обробка електричною дугою матриць для брикетування(КНТУ, 2015) Сіса, О. Ф.; Sisa, OlehВиконано обґрунтування технологічної схеми формоутворення бічних поверхонь утвору матриць для брикетування способом розмірної обробки електричною дугою з урахуванням особливостей фізичних механізмів їх утворення та гідродинамічних явищ в міжелектродному проміжку. Встановлені аналітичні зв’язки технологічних характеристик процесу розмірної обробки електричною дугою сталі Х12МФ з режимами обробки і геометричними параметрами. The article is dedicated to the development of technology and equipment method of packing dies processing with dimensional electric arc as high-performance alternative to traditional methods of processing. Fuel briquettes are formed by pressing force with the pressure up to 500 kN of pre-shredded waste wood and plant in the hole of matrix, where the process of aggregation goes. In the development of equipment and tools it is necessary to take into account the conditions that will ensure the formation of fuel briquettes. The most important parameter for pressing fuel briquettes is the energy which corresponds to the work of frictional forces against the walls of the die hole, since the pressure force transmitted to the side surface, is proportional to pressure in the longitudinal direction. The optimal parameter of the walls of the die hole is the roughness Ra = 3,2..6,3 mkm, which provides the frictional force when unitizing. It is suggested to get the die hole for briquetting by dimensional electric arc with a given roughness of Ra = 3,2..6,3 mkm of the side walls of the matrix, which allows you to take great allowances material at the lowest cost processing time. In such a case the cycle of matrix processing decreases in 4,1-5,2 times. The objectivity of technological schema of die hole formation by the method of dimensional processing by electric arc with consideration of specialties of physical mechanism of creation and hydrodynamic phenomena in electrode period was performed. The analytical connections of technological processing characteristics of sized processing by electrical arc of steel X12MF were established, with the modes of processing and geometrical parameters.Item type:Item, Оптимізація якісних характеристик поверхонь робочих деталей розділових штампів в умовах розмірної обробки електричною дугою(КНТУ, 2014) Шмельов, В. М.; Shmelyov, V.Виконано оптимізацію якісних характеристик поверхонь робочих деталей розділових штампів в умовах розмірної обробки електричною дугою (РОД). Показано залежність між конструкцією матриці і необхідною шорсткістю її робочої поверхні. Описано залежності якості обробленої поверхні робочих деталей розділових штампів від технологічних характеристик процесу РОД. The paper purpose-optimisation of qualitative performances of a surface of working details dividing ofstamps in the conditions of dimensional processing the electric arc. In a paper the analyzes of a construction of the matrix and a necessary surface roughness of working details of separating dies is carried out, on the basis of this gives recommended roughnesses of surfaces of working details received by methods of a classical electrical discharge machining. On the basis of experimental data derived the mathematical model of a surface roughness of working details dividing of stamps depending on the basic technical characteristics on process of dimensional processing the electric arc. It is shown that the surface roughness of working details dividing of stamps received by a mode of dimensional processing the electric arc, corresponds to the recommended surface roughness of these details received by classical methods of an electroerosion machining. Use of a mode of dimensional handling by an electric arc allows to receive working details of separating dies of the necessary sizes and with necessary indexes of a surface roughness of the worker of a part, and accordingly and to ensure necessary firmness, and lowering of the cost price of their manufacture. Using the method of dimensional processing the electric arc allows to receive of working details dividing of stamps the necessary sizes and with necessary indexes of a surface roughness of the worker of a part, and according to ensure necessary firmness, and lowering of the cost price of their manufacture.