Конструювання, виробництво та експлуатація сільськогосподарських машин. Загальнодержавний міжвідомчий науково-технічний збірник.
Permanent URI for this communityhttps://dspace.kntu.kr.ua/handle/123456789/19
Ідентифікатор медіа: R30-03925 (рішення Національної ради України від 25.04.2024 р. № 1418).
Мови видання: українська, російська, англійська, періодичність - один раз на рік.
Browse
9 results
Search Results
Item Структурно-логічна схема автоматичної системи управління замкнутою системою опалення та вентиляції теплиць(ЦНТУ, 2023) Кепко, О. І.; Лісовий, І. О.; Ковальчук, О. Ю.; Kepko, О.; Lisovyi, І.; Kovalchuk, Yu.В процесі проектування автоматичної системи управління замкнутою системою опалення та вентиляції теплиць з регенерацією повітря було обґрунтовано та розроблено структурно-логічну схему управління, яка передбачає управління технологічними параметрами (температурою, вологістю, концентрацією СО2, освітленістю). Структурно-логічна схема була створена на основі технологічної карти вирощування гливи звичайної з урахуванням зміни температури, вологості, концентрації СО2 та освітленості у функції часу. In the process of designing an automatic control system for a closed system of heating and ventilation of greenhouses with air regeneration, a structural and logical control scheme was substantiated and developed, which provides control of technological parameters (temperature, humidity, CO2 concentration, lighting.Item Застосування мехатронних систем в системі машин для тваринництва(ЦНТУ, 2023) Кравченко, В. В.; Войтік, А. В.; Лісовий, І. О.; Kravchenko, V.; Voitik, A.; Lisovyi, I.Розглянуто застосування мехатронних систем при утриманні тварин та птиці, забезпеченні мікроклімату, напуванні, кормороздаванні, видаленні гною та отриманні продукції. Проведені дослідження показують, що майже у всіх механізованих процесах в тваринництві використовуються мехатронні системи, які вже або використовуються на фермах або знаходяться ще на етапах розробки та досліджень. Основним рушієм впровадження мехатронних систем в тваринництві є зменшення затрат праці, покращений контроль за механізованими процесами на фермі, покращення виконання механізованих технологічних процесів та забезпечення комфорту тварин. The purpose of this work is the systematization of research and implementation of mechatronic systems in the system of machines for keeping, caring for and obtaining the primary products of animal husbandry.Item Лазерно-плазмове зміцнення попередньо термооброблених деталей автомобільного транспорту в АПК(ЦНТУ, 2021) Ковальчук, Ю. О.; Лісовий, І. О.; Kovalchuk, Yu.; Lisovyi, I.Наведено результати лазерно-плазмового впливу на структуру та мікротвердість поверхонь звичайної та після термічної обробки гартуванням з низьким та високим відпуском конструкційної сталі 40ХН з різною структурою. В результаті виявлено, що лазерно-плазмова обробка дозволяє проводити зміцнення поверхні даної сталі до високої твердості 9–11 ГПа на глибину близько 0,2 мм. Застосування лазерно-плазмової обробки для зміцнення поверхні можливе на різних етапах технологічного процесу виготовлення або ремонту деталей автомобільного транспорту в АПК. The aim of the work is to determine the laser-plasma effect on the structure and microhardness of surfaces of ordinary and after heat treatment by hardening with low and high tempering steel 40HN with different structure, to study the possibility of laser-plasma treatment to strengthen the surface at different stages of manufacturing or repair transport details in the agro-industrial complex. The article presents the results of laser-plasma exposure to the structure and microhardness of surfaces of ordinary and after heat treatment by hardening with low and high tempering steel 40HN with different structure: normalized or annealed steel immediately after machining, and after volumetric heat treatment with different types tempering for different hardness, determined by the purpose of the workpieces. First, the features of the microstructure and hardness of steel with a ferritic-pearlitic structure during laser-plasma treatment were studied. The highest temperature, which causes melting and evaporation of the material, during laser treatment occurs on the surface of the processed products. During further cooling due to intensive heat dissipation into the cold core of the metal in the melting zone is hardening from the liquid state and the formation of martensite. Adjacent to these areas is the zone of martensite obtained by quenching during cooling from the solid austenitic state. Then the influence of laser-plasma treatment on the features of the microstructure and hardness of steel with the structure of tempering sorbitol and with the structure of martensite was considered. Laser-plasma treatment can be used with high efficiency to strengthen structural steels. It allows to strengthen the surface of structural steel to a high hardness of 9-11 GPa to a depth of about 0.2 mm. The hardening effect is obtained on steels with different structure, characteristic for different stages of the technological process. Therefore, the use of laser-plasma treatment to strengthen the surface is possible at different stages of the technological process of manufacturing or repairing parts of road transport in agriculture.Item Дослідження структури та мікротвердості обробленої лазером поверхні чавунів(ЦНТУ, 2018) Ковальчук, Ю. О.; Лісовий, І. О.; Ковальчук, Ю. А.; Лисовый, И. А.; Kovalchuk, Yu.; Lisoviy, I.Проаналізовано вплив лазерної обробки на властивості поверхневого шару чавуну. Визначено структуру та мікротвердість зон лазерного впливу для чавуну марок СЧ21 і ВЧ40. Відмічено, що застосування швидкого сканування лазерного пучка поперек напрямку руху забезпечує згладжування поверхневого рельєфу оплавленого шару та поліпшення форми перерізу загартованої смуги, наближаючи її до прямокутної. Досліджено, що для зміцнення чавунів крім потужних СО2-лазерів можуть ефективно використовуватися твердотільні YAG-лазери потужністю від 400 Вт і вище. Проанализировано влияние лазерной обработки на свойства поверхностного слоя чугуна. Определена структура и микротвердость зон лазерного воздействия для чугуна марок СЧ21 и ВЧ40. Отмечено, что применение быстрого сканирования лазерного пучка поперек направления движения обеспечивает сглаживание поверхностного рельефа оплавленного слоя и улучшения формы сечения закаленной полосы, приближая ее к прямоугольной. Исследовано, что для упрочнения чугунов кроме мощных СО2-лазеров могут эффективно использоваться твердотельные YAG-лазеры мощностью от 400 Вт и выше. The purpose of this work is to study the method of surface laser treatment regarding the effect of laser radiation on the structure and microhardness of laser influence zones in the surface layer of cast iron to improve performance characteristics such as hardness and wear resistance of the corresponding parts of agricultural machinery. The ratio of austenitic and martensitic components in SCh21 cast iron in the structure of the hardened layer is significantly affected by the duration of the radiation effect. With its increase in the near-surface layer and in the depth of the laser-impact zone, separate areas of residual austenite with microhardness H100 = 500-560 kgf/mm2 appear. In the deep areas of the hardened layer, austenite is localized around phosphide eutectic inclusions, that is, in the most carbon-rich areas. Due to laser hardening of high-strength HF40 cast iron with the parameters specified in the work, the microhardness of the bleached layer was 7•103...8.7•103 MPa, and in the laser hardening zone from the solid state for austenitic-martensitic structure - 6•103...7 5•103 MPa. The choice of the hardening mode of cast iron SCh21 and the corresponding structural state in the zone of laser influence should be carried out taking into account the operating conditions of a particular part, since austenite may have a different effect on the wear resistance. For example, with respect to the friction pair of an engine cylinder – a compression ring, residual austenite may contribute to a better running-in of these parts. The use of fast scanning of a laser beam across the direction of motion provides smoothing of the surface relief of the melted layer and improving the shape of the hardened strip, bringing it closer to a rectangular one. In addition to high-power CO2 lasers, solid-state YAG lasers with a power of 400 W and more can be effectively used for hardening cast irons. Thus, surface laser treatment can also be successfully applied to cast iron, used by domestic manufacturers of agricultural machinery parts. This will ensure a significant increase in the performance characteristics of the respective products and will create prerequisites for the replacement of significantly more expensive steels with cast irons in certain cases.Item Особливості застосування поверхневої лазерної обробки деталей сільськогосподарських машин з чавуну(ЦНТУ, 2017) Ковальчук, Ю. О.; Лісовий, І. О.; Kovalchuk, Y.; Lisoviy, I.Проаналізовано внутрішні процеси в результаті впливу лазерного випромінювання на поверхню деталей сільськогосподарської техніки з чавуну. Визначено залежність мікротвердості досліджуваних зразків від потужності лазерного випромінювання. Відмічено, що збільшення швидкості обробки призводить до помітного зниження середніх значень мікротвердості чавуну. Досліджено, що поєднання лазерної обробки із подальшим поверхневим пластичним деформуванням може забезпечити значне підвищення зносостійкості деталей із чавуну. Determine the effect of laser treatment on the structure and properties of cast iron for improving the operational characteristics of the relevant agricultural machinery parts is the goal of the work. Internal processes as a result of the effect of laser radiation on the surface of samples from cast iron are analyzed. The dependence of the microhardness of the investigated samples on the laser radiation power is determined. Increasing the processing speed leads to a noticeable decrease in the average values of the microhardness of the cast iron. Combining laser treatment with further surface plastic deformation can provide a significant increase in wear resistance of parts from cast iron. Cast iron can be effectively processed by laser radiation, which will ensure high performance characteristics of the relevant agricultural machinery parts.Item Визначення відстані відкидання ґрунту щітковим робочим органом при розкритті кореневої системи маточних рослин(КНТУ, 2015) Войтік, А. В.; Кравченко, В. В.; Лісовий, І. О.; Павленко, І. І.; Voytik, Andriy; Kravchenko, Vasyl; Lisovoy, Ivan; Pavlenko, IvanВ статті розглянуто технології та технічні засоби для розкриття кореневої системи маточних рослин клонових підщеп. Встановлено, що раціональним варіантом є використання комбінованого пристрою з пасивними відгортачами та активними циліндричними щітками з вертикальними осями обертання і гнучкими робочими елементами. Проаналізовано робочий процес одного прутка ворсу щітки та визначено сили, які на нього діють. В результаті аналізу попередніх досліджень, що стосуються відстані відкидання частинок при роботі циліндричних щіток, з використанням теорії розмірності і подібності виведено рівняння для визначення відстані відкидання частинок ґрунту або субстрату, який вкриває кореневу систему маточних рослин. Встановлено, що для забезпечення умов залишення ґрунту в межах рядка, з якого він видаляється, на машині для розкриття кореневої системи маточних рослин необхідно встановлювати додаткові щитки. Improvement brush the working bodies of machines for disclosure of the root system of the mother plant with the aim of increasing the degree of removal of soil. The article considers technologies and technical means for the disclosure of the root system of the mother plant clonal rootstocks. Found that the rational option is the use of the combined device with passive and active working element cylindrical brushes with vertical axes of rotation and flexible working elements. Analyzed the workflow of one rod lint brush and determined forces that are not. As a result of analysis of previous studies relating to the distance of the drop particles when working cylindrical brushes using the theory of dimensions and similarity of the equation to determine the distance of the drop of soil particles or soil that covers the root system of the mother plant. It is established that to ensure the abandonment of the land within its range from which it is removed, vehicles for disclosure of the root system of the mother plant, you must install additional shields.Item Аналіз кінематики руху і обґрунтування конструктивних параметрів зубчастого диска-очисника для прямого посіву(КНТУ, 2008) Лісовий, І. О.В статті розглянуто кінематику руху зубчастого диска-очисника, встановлено залежність кута входження зуба у ґрунт від глибини його ходу і радіуса обертання, залежність розрахунку кута установки зуба з метою реалізації його раціональної взаємодії з ґрунтом. In the article the kinematics of motion of toothed disk is considered, dependence of corner of entrance of tooth in soil from the depth of his motion and radius of rotation is set, dependence of computation of corner of setting of tooth with the purpose of realization of his rational co-operation with soil.Item Дослідження енергетичних показників і встановлення раціональних параметрів зубчатого робочого органу сошника прямого посіву(КНТУ, 2011) Бойко, А. І.; Свірень, М. О.; Лісовий, І. О.; Bojko, A.; Sviren, N.; Lisovij, I.В статті розглянута взаємодія зуба з ґрунтом, встановлена залежність впливу кута установки зуба на енергетичні показники руйнування ґрунту при різних рівнях заглиблення і радіусах обертання зуба. The article discloses interaction of a tooth with soil. The dependence of the influence of the corner of a tooth on energy indicators of soil destruction in different levels of deepening and the radius of tooth rotation has been established.Item Енергетика процесу перерізання рослинних решток комбінованим сошником для прямого посіву(КНТУ, 2012) Лісовий, І. О.; Бойко, А. І.; Свірень, А. І.; Пашинський, В. А.; Lisovij, I.; Bojko, A.; Sviren, N.; Pashinskiy, V.В статті розглянуто дослідження раціональної форми ріжучого елемента при виконанні прямого посіву та виявлення мінімальних затрат на перерізання рослинних решток і направлення їх на бокові сторони борозни. The article discloses the research of rational form of cutting element during direct sowing and detection of minimal costs on cutting plant leftovers and directing them onto sideways of the furrow.