Конструювання, виробництво та експлуатація сільськогосподарських машин. Загальнодержавний міжвідомчий науково-технічний збірник.
Permanent URI for this communityhttps://dspace.kntu.kr.ua/handle/123456789/19
Ідентифікатор медіа: R30-03925 (рішення Національної ради України від 25.04.2024 р. № 1418).
Мови видання: українська, російська, англійська, періодичність - один раз на рік.
Browse
10 results
Search Results
Item Оцінка механічних характеристик матеріалів при лазерному термозміцненні деталей сільськогосподарської техніки(КНТУ, 2016) Мажейка, О. Й.; Mazheyka, О.Проведені випробування сталей і чавунів на характеристики опору втомі після лазерної обробки деталей сільськогосподарської техніки. Встановлено зв’язок потужності лазерного випромінювання та швидкості обробки для досягнення якісних показників процесу лазерного термозміцнення деталей. Доказано, що лазерне термозміцнення дозволяє збільшувати значення меж витривалості. Разом з тим показано, що обробка лазером може призводити до зниження характеристик опору втомі. The aim of this work was to study the strength characteristics of agricultural machinery parts after laser strengthening of the recovery, which enhances their life. Past studies testing steels and cast irons on the characteristics of fatigue resistance after laser treatment in respect of parts of agricultural machinery. The connection laser power and processing speed to achieve yakystnyh laser process parameters thermal hardening details. Proved that laser thermal hardening allows to increase the value limits of endurance. However, it is shown that laser treatment can lead to a decrease in fatigue resistance characteristics. Significant influence on the performance characteristics of materials, residual stresses, hardness, micro-structure and surface modes provide treatment. Locality laser treatment allows processing of hard-surface areas, so we can talk about the significant benefits this type of consolidation of the processing stress concentrators. The study found that laser thermal hardening allows to increase the value limits of endurance. However, it is shown that laser treatment can lead to a decrease in fatigue resistance characteristics. Fatigue resistance change with laser treatment is associated with structural changes in the treated area, its hardness, residual stress generated, micro surface. These properties associated with processing technological parameters - type of laser radiation power, speed processing, strengthening geometry drawing paths.Item Конструкція головки для нанесення зносостійких електродугових покриттів на внутрішні поверхні деталей сільськогосподарської техніки(КНТУ, 2009) Мажейка, О. Й.; Маркович, С. І.; Рябоволик, Ю. В.; Mazheyka, О.; Markovich, S.; Ryabovolik, Y.В статті здійснено розрахунок струмознімних направляючих електродугового розпилювача для нанесення зносостійких покриттів на внутрішні поверхні корпусних деталей сільськогосподарської техніки. При цьому отримано рівняння, що описують оптимальну форму кривизни направляючих з урахуванням фізико-механічних властивостей і розмірів порошкових та суцільнотягнутих електродних дротів. The calculation of sending arc nebulizer for causing of wear proof coverages on the internal surfaces of cabinet-type details of agrarian technique is carried out in the article. Equalizations which describe the optimum form of curvature sending taking into account physical and mechanical properties and sizes of powder- like and continuous electrodes are thus got.Item Лазерне наплавлення та термомеханічна обробка композиційних матеріалів з пам'яттю форми(КНТУ, 2009) Головко, Л. Ф.; Мажейка, О. Й.; Маркович, С. І.; Golovko, L.; Mazheyka, A.; Markovich, S.В статті викладені положення концепції лазерного наплавлення композиційних покриттів з пам'яттю форми, досліджено особливості структуроутворення і властивостей матеріалів з поверхнево- модифікованим шаром із сплаву з пам'яттю форми на основі ТІМ , сформованим при лазерній дії. Розроблено технологічний процес поверхневого модифікування з поетапною термічною обробкою і термомеханічним тренуванням шляхом поверхневої пластичної деформації з обтисканням або обкаткою. In the articles the expounded positions of conception of the laser causing of composition coverages are with memory of form, the features of gelation and properties of materials are investigational with the superficially modified layer from an alloy with memory of form on the basis of TiNi, formed at a laser action. The technological process of the superficial retrofitting is developed with stage-by-stage heat treatment and thermo mechanical training by a superficial flowage with a preload or rolling.Item Розробка комплексу обладнання для відновлення та зміцнення деталей сільськогосподарських машин класу «круглий стрижень» з застосуванням комбінованої технології(КНТУ, 2015) Маркович, С. І.; Мажейка, О. Й.; Дмитренко, О. В.; Markovich, Sergey; Mazheyka, Oleksandr; Dmitrenko, OleksandrВ статті розроблено комплекс обладнання для відновлення та зміцнення деталей сільськогосподарських машин класу «круглий стрижень» з застосуванням комбінованої технології. Розроблено конструкцію вертикальної камери, електродугового розпилювача з незалежним приводом електродних дротів та оптимальною формою направляючих, механізм приводу подачі мікроплазмотрона зі схемою теристорного управління. In the article the question of implementing the idea of thermal influence on arc spraying using microplasma concomitant treatment in the recovery of parts of the "round core". Thus using arc spray coating deposited on the surface of the workpiece to be rotated. Simultaneously held microplasma spray finishing first base material, and each layer of the coating. To address the problems developed arc spraying chamber with concomitant treatment with micro plasma processed vertical shaft. Electric-spray developed with independent variable speed feed wire patented in Ukraine. Designed guide optimal form of electric wires. Designed for precision equipment supply and stepless speed regulation regarding the movement of micro plasma arc torch spray. Founded equipment allows to investigate the effect of related micro plasma treatment at arc spraying on adhesion, cohesion, microstructure uniformity, porosity, wear resistance of coatings and implement the idea of creating a composite coating with refractory fillers, allowing to implement in production the proposed manufacturing process of restoring parts of the "round core" , to expand the scope of application of arc spraying and improve the quality of renewable parts.Item Features a combined laser processing of titanium-nickel alloys(КНТУ, 2015) Mazheyka, Aleksandr; Мажейка, О. Й.The article describes a study of the combined laser processing (CLP) for coating of titanium-nickel alloy. The structural phases that are inherent in shape memory alloys, for a considerable time by X-ray analysis. The dependence of the volume fraction of martensite, depending on the depth. It was determined that the main mechanism of relaxation during the laser treatment is combined partial martensitic transformations in phase B2 in B19. The studies confirm the effectiveness of CLP. Метою роботи було визначення параметрів структур нікель-титанових сплавів при комбінованій лазерній обробці. В статті описано дослідження технології комбінованої лазерної обробки (КЛО) для отримання покриттів з титан-никелевих сплавів. Досліджені структурні фази, яки притаманні сплавам з пам’яттю форми, на протязі значного часу за допомогою рентгеноструктурного аналізу. Встановлена залежність об’ємної долі мартенситу в залежності від глибини залягання. Визначено, що основним механізмом релаксації при проведенні комбінованої лазерної обробки є часткові мартенситні перетворення фази В2 у В19. Деформаційні зміни структур сплавів TiNi при комбінованій лазерній обробці призводять до загартування поверхневих шарів і може бути використовано при зміцненні деталей сільськогосподарської техніки.Item Вплив поруватості на трибологічні характеристики електродугових покриттів з порошкових дротів(КНТУ, 2014) Студент, М. М.; Ступницький, Т. Р.; Гвоздецький, В. М.; Маркович, С. І.; Мажейка, О. Й.; Student, М.; Stupnickiy, Т.; Gvozdeckiy, V.; Markovich, S.; Mazheyka, А.В статті досліджено вплив поруватості на трибологічні та механічні характеристики еллектродугових покриттів. Визначено, що структурою покриття з порошкових дротів є композит, де чергуються металеві ламелі та ламелі із оксидів, а також пори. Із ростом тиску повітряного струменю розмір структурних складових поверхні покриття та розмір пор зменшується. Встановлено позитивний вплив поруватості на трибологічні характеристики покриттів при терті за граничного мащення. Influence of porosity is investigational the article on mechanical properties of arc coatings. Exposed to research of coatings from different types powder-like. A structure, phase composition, porosity, resistance to the friction, cohesion of coatings depending on pressure of transporting gas, was studied. Determination of coefficient friction of coatings is exposed to research in the conditions of dry friction and border greasing It is set, that from powder-like wires the structure of coatings there is a compo, where metallic lamels and lamels alternate from oxides and also pore. With growth of pressure of air-blast the size of structural constituents of surface of coatings and size of pores diminishes. Positive influence of porosity is set on mechanical properties of coatings in the conditions of border friction. Аrc coatings of gradient type provide high mechanical properties of coatings at to the low level of remaining tensions of in them.Item Дослідження впливу вмісту легуючих елементів в шихті порошкового дроту на придатність до обробки електродугових покриттів(КНТУ, 2011) Черновол, М. І.; Мажейка, О. Й.; Маркович, С. І.; Chernovol, М.; Mazheyka, O.; Markovich, S.В статті приведено результати дослідження впливу легуючих елементів в шихті порошкового дроту на вміст кисню в електродуговому покритті та його придатність до обробки лезовим інструментом. In the article a method and results of research of influence is resulted С, Cr and Al in the charge of powder-like wire on composition and fitness to tooling of coverages. The method of determination of fitness is given to treatment on composition of powder-like wire.Item Дослідження трибологічних характеристик модифікованих поверхонь з регулярним мікрорельєфом(КНТУ, 2010) Мажейка, О. Й.; Маркович, С. І.; Савченко, О. П.; Mazheyka, А.; Markovich, S.; Savchenko, О.В статті розглянуто проблему підвищення трибомеханічних характеристик поверхонь завдяки створенню регулярного мікрорельєфу з послідуючим нанесенням мідного покриття. Проведено огляд методів нанесення регулярного мікрорельєфу. Приведено технологію платовершинного хонінгування та нанесення покриття, результати дослідження трибологічнічних характеристик покриття та експлуатаційні випробування гільз циліндрів ДВЗ, оброблених по пропонованій технології. In the article the problem of increase of tribe of mechanical descriptions of surfaces is considered due to creation regular мicro relief with the subsequent causing of copper coverage. Technology of plateau of the vertex honing and overcoating, results of research of tribologichnoy descriptions of coverage and operating tests of shells of cylinders of engines, treated on the offered technology, is resulted.Item Зміцнення деталей сільськогосподарських машин сучасними технологіями(КНТУ, 2010) Мажейка, О. Й.; Чайковський, О. Б.; Лутай, А. Н.; Mazheyka, А.; Тсhaykovski, А.; Lutay, A.Проаналізовані відомі методи підвищення зносостійкості робочих органів (деталей) сільськогосподарських машин. Запропонована нова технологія зміцнення деталей сільськогосподарських машин лазерною наплавкою композиційних матеріалів з термомеханічною обробкою Наведені результати порівняльних випробувань найбільш ефективних твердих наплавлень. Намічені подальші дослідження стосовно грунтово-кліматичних умов Кіровоградської області. The known methods of increase of wearproofness of workings organs (details) of agricultural machines are analysed. New technology of consolidating of details of agricultural machinesis offered laser welding of composition materials with termo-mechanical treatment. Results of comparative tests of most effective hard weldings . The ways of research adapted to soil-climatic conditions of Kirovograd regions are outlined.Item Проектування інструменту для різних методів обробки пластично-поверхневим деформуванням(КНТУ, 2010) Мажейка, О. Й.; Mazheyka, А.Запропонована методика проектування інструменту для обробки ППД. Приведені методи обробки та можливі схеми їх реалізації. Визначені основні чинники, що впливають на параметри інструменту. A design technique instrument is offered for treatment of PPD. The methods of treatment and possible charts of their realization are resulted. Basic factors, influencing on the parameters of instrument are certain the choice of proper material is offered for an instrument, developed flow-chart of algorithm of planning of instrument for PPD.