Конструювання, виробництво та експлуатація сільськогосподарських машин. Загальнодержавний міжвідомчий науково-технічний збірник.
Permanent URI for this communityhttps://dspace.kntu.kr.ua/handle/123456789/19
Ідентифікатор медіа: R30-03925 (рішення Національної ради України від 25.04.2024 р. № 1418).
Мови видання: українська, російська, англійська, періодичність - один раз на рік.
Browse
4 results
Search Results
Item Попередні дослідження пасивного струнного решета(ЦНТУ, 2022) Васильковський, О. М.; Лещенко, С. М.; Петренко, Д. І.; Мороз, С. М.; Нестеренко, О. В.; Vasylkovskyi, O.; Leshchenko, S.; Petrenko, D.; Moroz, S.; Nesterenko, О.У статті викладені результати досліджень роботи моделі оригінального струнного решета. На основі аналізу наукових праць сформульовано гіпотезу щодо підвищення ефективності сепарації зерна і зниження енергетичних витрат шляхом використання струнних пасивних решіт з шнурів Dyneema. Попередні дослідження моделі підсівного решета були проведені шляхом реалізації плану повного факторного експерименту. Встановлено працездатність і виявлені основні показники роботи оригінального решета. Виявлені недоліки конструкції і сформульовані завдання для подальших досліджень. The article presents the results of research into the operation of the model of the original string sieve. The sieve is equipped with synthetic strings made of ultra-small diameter Dyneema braided cord. The purpose of this study is to evaluate the performance and identify the main indicators of the technological efficiency of the proposed fixed sieve installed at an angle to the horizon. Preliminary studies of the sowing sieve model were carried out by implementing the plan of a full factorial experiment. The experiments were carried out on a model of a seed sieve with holes of 2 mm. In the course of experiments, a post-harvest heap of winter wheat with natural clogging was used. The criterion for evaluating the efficiency of separation is the mass of seeding, and the specific feed and the angle of inclination of the sieve are the operating factors. The operational efficiency was established and the main performance indicators of the model were identified. The statistical mathematical model of the process allows us to assert the linear dependence of the criterion on the operating factors and to obtain a quantitative assessment of their influence on the process of cleaning the grain mixture. The surface of the response of the mass of the selected seeding from the specific loading of a unit of the sieve area and the angle of its inclination is constructed. An analysis of the regression equation and the response surface was carried out, during which design flaws were identified and tasks for further research were formulated. The factor that was found to be influential in the course of the previous experiments – the angle of inclination at the minimum value does not fully ensure guaranteed performance, since during the experiments clogging and accumulation of piles on the separating surface were periodically observed. An increase in the mass of the selected seeding is achieved by reducing the angle of the passive sieve to 17º and increasing the specific supply to 160 kg/dm2 ◌ּh. A decrease in feed worsens the sieving process, especially at a small angle of inclination of the sieve, however, according to the Student's test, it is not significant. The resulting non-classical dependence may indicate the imperfection of the layout, the influence of unforeseen factors, etc., and requires further research.Item Обґрунтування конструктивної схеми пневморешітного сепаратора зерна(ЦНТУ, 2021) Васильковський, О. М.; Лещенко, С. М.; Нестеренко, О. В.; Петренко, Д. І.; Якименко, С.М.; Vasylkovskyi, O.; Leshchenko, S.; Nesterenko, O.; Petrenko, D.; Iakymenko, S.Статтю присвячено удосконаленню конструкції відцентрового пневморешітного сепаратора для розділення компонентів зернових сумішей. Базова конструкція задовільно виконує технологічний процес, однак має відносно великі вертикальні габарити за рахунок використання замкненої системи аспірації з подвійним очищенням зернової маси повітряним потоком. В роботі наведено концепцію удосконалення системи аспірації, що дозволить суттєво зменшити висоту, а також викладено методику проектного конструкторського розрахунку параметрів удосконаленої машини. The aim of the article is to improve the design of the original centrifugal grain separator. The separator is designed to separate the components of grain materials by size and aerodynamic properties. The basic design satisfactorily performs the technological process, but has large dimensions vertically. Reducing the size will simplify the design and reduce the cost of the machine. The article proposes to replace the double pneumatic cleaning of grain material with a single one. At the same time the car gets rid of the closed aspiration system. The closed aspiration system has operational advantages, however difficult adjustment reduces indicators of technological efficiency of pneumatic cleaning of grain. The original pneumatic cleaning system allows you to remove light impurities without creating significant air resistance, due to the lack of countercurrent movements. In addition, the use of an inclined pneumatic channel does not require the creation of high-speed airflow. As a result of the proposed improvement simplifies the structure and regulation of the separator, as well as reduces its size and weight. In addition to the modernization of the design of the pneumatic-sieve separator, the article presents the method of design engineering calculation of its basic geometric parameters. Depending on the specific capacity of the upper (ear) sieve and the characteristics of the grain mixture is determined by its length and angle. The remaining geometric parameters are derived from the above. Based on preliminary calculations, the following conclusions can be drawn. The use of the proposed scheme will reduce the height and weight of the centrifugal pneumatic sieve grain separator. Replacing the double air cleaning with a single one will simplify the adjustment of the machine. Experimental establishment of indicators of technological efficiency of the proposed separator will theoretically determine the dimensions and automate the design process of grain cleaning machines created by a similar scheme.Item До створення концепції «ідеального» решета зернового сепаратора(ЦНТУ, 2020) Васильковський, О. М.; Лещенко, С. М.; Мороз, С. М.; Нестеренко, О. В.; Молокост, Л. А.; Vasylkovskyi, O.; Leshchenko, S.; Moroz, S.; Nesterenko, O.; Molokost, L.; Васильковский, А. М.; Лещенко, С. Н.; Мороз, С. Н.; Нестеренко, А. В.У статті викладені міркування щодо створення умов для інтенсифікації процесу сепарації зерна за геометричними ознаками. Проведено огляд конструкцій і аналіз роботи відомих решітних поверхонь з позиції можливості забезпечення високих показників технологічної ефективності за рахунок прискорення орієнтації часток відносно отворів решета. Встановлено, що найбільш сприятливі умови орієнтації забезпечують поверхні, утворені повздовжніми елементами малого перерізу обтічної форми, що мінімізують можливість розташування на них часток в положеннях стійкої рівноваги. Виявлено теоретичні можливості збільшення площ живого перерізу та коефіцієнтів живого перерізу решітних полотен, що не мають поперечних перетинок. Наведені залежності сумарної ширини повздовжніх перетинок і коефіцієнта живого перерізу решіт від ширини повздовжніх перетинок для різних решіт. Це дає можливість візуальної оцінки необхідності збільшення живого перерізу решіт шляхом зменшення ширини повздовжніх перетинок, які їх утворюють. Суттєве зменшення ширини перетинок стає можливим завдяки використання нових матеріалів – плетених шнурів з надвисокомолекулярних поліетиленів типу Spectra/Dyneema, що забезпечують високі показники механічної міцності і зносостійкості при «абсолютній» нерозтяжності. The article presents considerations for creating conditions for the intensification of the process of grain separation by geometric features. The review of constructions and the analysis of work of known sieve surfaces from a position of possibility of maintenance of high indicators of technological efficiency at the expense of acceleration of orientation of particles concerning sieve apertures is carried out. It is established that the most favorable orientation conditions are provided by the surfaces formed by longitudinal elements of small cross-section of streamlined shape, which minimize the possibility of placing particles on them in positions of stable equilibrium. Theoretical possibilities of increasing the living cross-sectional areas and live cross-sectional coefficients of sieve canvases without cross-sections are revealed. The dependences of the total width of the longitudinal sections and the coefficient of the living cross section of the sieves on the width of the longitudinal sections for different sieves are given. This makes it possible to visually assess the need to increase the living cross section of the sieves by reducing the width of the longitudinal sections that form them. A significant reduction in the width of the partitions is possible due to the use of new materials - braided cords made of ultra-high molecular weight polyethylene type Spectra / Dyneema, which provide high mechanical strength and wear resistance with «absolute» inextensibility. В статье изложены соображения по созданию условий для интенсификации процесса сепарации зерна по геометрическим признакам. Проведен обзор конструкций и анализ работы известных решетных поверхностей с позиции возможности обеспечения высоких показателей технологической эффективности за счет ускорения ориентации частиц относительно отверстий решета. Установлено, что наиболее благоприятные условия ориентации обеспечивают поверхности, образованные продольными элементами малого сечения обтекаемой формы, которые минимизируют возможность расположения на них частиц в положениях устойчивого равновесия. Выявлены теоретические возможности увеличения площади живого сечения и коэффициента живого сечения решетных полотен, которые не имеют поперечных перегородок. Приведены зависимости суммарной ширины продольных перегородок и коэффициента живого сечения решет от ширины продольных перегородок для различных решет. Это дает возможность визуальной оценки необходимости увеличения живого сечения решет путем уменьшения ширины продольных перегородок, которые они образуют. Существенное уменьшение ширины перепонок становится возможным благодаря использованию новых материалов - плетеных шнуров их сверхвысокомолекулярных полиэтиленов типа Spectra/Dyneema, обеспечивающих высокие показатели механической прочности и износостойкости при «абсолютной» неростяжимости.Item Аналіз сучасного стана повітряної сепарації зерна(КНТУ, 2006) Васильковський, М. І.; Гончарова, С. Я.; Лещенко, С. М.; Нестеренко, О. В.В статті розглянуто сучасний стан повітряної сепарації зерна найбільш розповсюдженими зерноочисними машинами загального призначення. In article the modern condition of air separation of a grain by the most widespread graincleaning by general purpose machines is considered