Конструювання, виробництво та експлуатація сільськогосподарських машин. Загальнодержавний міжвідомчий науково-технічний збірник.
Permanent URI for this communityhttps://dspace.kntu.kr.ua/handle/123456789/19
Ідентифікатор медіа: R30-03925 (рішення Національної ради України від 25.04.2024 р. № 1418).
Мови видання: українська, російська, англійська, періодичність - один раз на рік.
Browse
4 results
Search Results
Item Оцінка рівномірності розподілу та засміченості зерна при його багаторівневому введенні в пневмосепаруючий канал(ЦНТУ, 2021) Нестеренко, О. В.; Лещенко, С. М.; Васильковський, О. М.; Петренко, Д. І.; Nesterenko, O.; Leshchenko, S.; Vasylkovskyi, O.; Petrenko, D.Одним із важливих показників ефективності роботи пневмосепаруючих каналів є рівномірність поля швидкостей повітряного потоку, яка в свою чергу залежить від розподілу зернового матеріалу в робочій зоні сепарації. В статті приведені результати розподілу зернового матеріалу при багаторівневому способі введення зерна, а також його вплив на засміченість легкими домішками по висоті пневмосепаруючого каналу. В результаті досліджень отримано залежності засміченості очищеного зерна легкими домішками від кількості задіяних рівнів живильного пристрою. The uniformity of grain distribution in a pneumatic separation channel is an important factor and it significantly affects the quality of grain cleaning. Indeed, with uneven feeding, impurities entering the pneumatic separating channel, to a large extent, are located in the middle or lower layers of grain flow, which impairs the possibility of their release into the settling chamber. Feeders are used to create a more uniform distribution of grain in the operating area of the pneumatic separating channel. They provide conditions under which grain material is fed into the air stream by a thin layer of directed jet. This feeding can significantly improve the interaction of the components of the input grain material with air, increasing the likelihood of their release, as well as minimize the contact of particles of the grain mixture, which significantly increases the efficiency of air flow. Based on the review and analysis of feeder designs, we have proposed a feeder for multi-level grain introduction. The use of such a feeder can significantly improve the quality of pneumo-separation, but there is a possibility of light impurities in the upper grain layers, which can affect the completeness of the separation of the purified grain. Experimental studies were conducted to determine the effect of multilevel introduction on the content of light impurities in the purified grain along the height of the pneumatic separation channel, as well as to analyze the distribution of grain mixture in the operating separation area. As a result of the conducted research it is determined that the number of involved levels of introduction of the feeding device influences the degree of clogging of the cleared grain, thus, uniformity of distribution of grain improves at increase in quantity of levels. In particular, when using up to 4 levels of the feeder under load qbi = 350 kg/dm·h at each level, the amount of light impurities entering the purified grain is not more than 3% of their total weight in the source material.Item Дослідження режимних характеристик гравітаційної напрямної кривої живильного пристрою(ЦНТУ, 2020) Нестеренко, О. В.; Васильковський, О. М.; Петренко, Д. І.; Артеменко, Д. Ю.; Nesterenko, О.; Vasylkovskyi, O.; Petrenko, D.; Artemenko, D.; Нестеренко, А. В.; Васильковский, А. М.; Петренко, Д. И.Враховуючи взаємозв’язок між швидкістю введення зернового матеріалу до пневмосепараційного каналу (ПСК) та його питомим навантаженням є необхідним дослідження режимних характеристик пристроїв, які встановлюються безпосередньо перед введенням в ПСК. В статті висвітлені експериментальні дослідження руху зернового матеріалу по гравітаційній напрямній кривій живильного пристрою пневмосепаратора з метою визначення її раціональних параметрів при забезпеченні заданої швидкості введення зерна в канал. Отримані експериментальні залежності, які дозволяють обґрунтувати основні параметри напрямної поверхні живильного пристрою. The rate of the feed velocity and specific load in the air separator are interrelated and require a rational approach to their choice, because reducing the rate of velocity increases grain flow thickness, which adversely affects the efficiency of grain separation in the separation zone, but limits separator performance. Based on the research of many authors, it was concluded that the feed velocity of grain material into the pneumatic separation channel should be in the range of 0.4… 0.6 m/s. Taking into account that using a feeder unit for multilevel grain input, the total thickness of grain flow is divided by the number of the involved levels of input. The main condition is to ensure a single layer of grain feed at the velocity at which the most intense release of light impurities. Therefore, the purpose of the study is to identify rational parameters of the guide gravitational surface of the feeder unit with the provision of appropriate performance characteristics of the grain flow during its multilevel feeding into the pneumatic separating channel. As a result of experimental research, the dependences of the modes of movement of grain material on the gravitational guide curve on its main parameters, namely, the length of the acceleration section Lp, its angle α and the radius of the arcuate section r. On the basis of the carried-out research parameters of a gravitational guide surface at which a single-layer mode of movement of grain material for a range of specific loadings is reached are established qB = 250 – 500 kg/hour. Accordingly, for the conditions of movement of grain material with a thickness of one grain with the velocity of feeding into the pneumatic separation channel vв = 0.5…0.6 m/s, the rational parameters of the guide gravity curve for cereals with the internal friction coefficient φтер = 0.47…0.73 there are: the length of the acceleration section Lp = 0.2 m, the angle of its inclination α = 33° and the radius of the arcuate section r = 0.15 m. Учитывая взаимосвязь между скоростью введения зернового материала в пневмосепарационный канал (ПСК) и его удельной нагрузкой, существует необходимость исследования режимных характеристик устройств, которые устанавливаются непосредственно перед вводом в ПСК. В статье освещены экспериментальные исследования движения зернового материала по гравитационной направляющей кривой питательного устройства пневмосепаратора с целью определения её рациональных параметров при обеспечении заданной скорости введения в канал. Получены экспериментальные зависимости, которые позволяют обосновать основные параметры направляющей поверхности питательного устройства для многоуровневого введения зерна.Item Аналітичні дослідження контактного руху легких домішок у пневмосепаруючому каналі(ЦНТУ, 2017) Нестеренко, О. В.; Петренко, Д. І.; Павленко, І. І.; Лещенко, С. М.; Гончарова, С. Я.; Nesterenko, О.; Petrenko, D.; Pavlenko, I.; Leschenko, S.; Honcharova, S.Враховуючи складність та випадковість пневмосепараційного процесу, на який впливає значна кількість факторів, є необхідним вирішення наукового завдання щодо встановлення закономірностей контактної взаємодії легких домішок з зерном в зоні пневмосепарації. В статті розглянуто контактний рух легких домішок через багатошаровий зерновий потік в вертикальному пневмосепаруючому каналі (ПСК) при їх багаторівневому одношаровому введенні. Отримані теоретичні залежності, які дозволяють встановити закономірності впливу основних конструктивно-технологічних параметрів ПСК на якість процесу сепарації. The separation of grain materials in the air separation channel occurs in rather difficult conditions, since light impurities, which are located in the lower cereal layers for the separation into the sediment chamber, require, with a minimum change in trajectory, to cross all above-placed seed moving in a downward direction. As a result of this movement there is a contact between light impurities and grain, which significantly affects the quality of cleaning. Therefore, a very important task is the analytical research aimed at investigating the contact interaction of light impurities with grain in the air separation channel and its effect on the quality of separation. Taking into account the multilevel feeding of the material in the PSC it is necessary to determine its influence on the qualitative parameters of the separation process and the establishment of the basic laws of the interaction of light impurities with grain material in the working area of the PSC. As a result of the theoretical analysis, the regularity of the contact motion of light impurities is established at the multilevel feeding of grain material in the PSC, which allows to obtain the averaged trajectories of impurities after interaction with grain layers during aerodynamic separation. It is determined that the allocation of light impurities depends on their time and velocity through the grain layers, which vary depending on the angle of contact of impurities with grain, as well as from the place of installation of the upper point of the output of grain hɠ.ɜ.. With six-level introduction of the material with the placement of grain particles in the direction of movement in the PSC with an interval equal to their size (2R) the place of installation of the upper point of the output of grain hɠ.ɜ. must be at a height hɠ.ɜ.= 0,05 ... 0,055 m relative to the level I of the input. The purpose of further researches should be to determine the qualitative characteristics of pneumatic separation in the contact interaction of grain material with air flow at its multilevel introduction into the PSC.Item Дослідження безконтактного руху легких домішок у вертикальному пневмосепаруючому каналі(КНТУ, 2016) Нестеренко, О. В.; Лещенко, С. М.; Петренко, Д. І.; Гончарова, С. Я.; Мельник, Ю. В.; Nesterenko, О.; Leshchenko, S.; Petrenko, D.; Goncharova, S.; Melnik, Y.В статті розглянуто безконтактний рух легких частинок в вертикальному ПСК при їх багаторівневому одношаровому введенні. При прийнятих допущеннях отримані закономірності безконтактного руху легких частинок в ПСК, які дозволяють визначити раціональні параметри живильного пристрою. В результаті теоретичного аналізу визначено час перебування легких частинок в ПСК при їх безконтактному русі та зону їх виділення під час розділення зернової суміші повітряним потоком. Rational use of air flow during the separation of the grain mix is one of the main problems in pneumatic separation. Thus, it is necessary to ensure appropriate quality cleaning performance while increasing grain cleaning machines (GCM). In greater degree it concerns pneumatic GCM, who have somewhat lower rates than specific performance sieve. Therefore, improvement and development of new pneumatic structures is an important and urgent task. Taking into account the insufficient analytical scrutiny process at pneumatic separation multilayer material in grain movement pneumatic separating channel (PSC) is necessary tasks to establish patterns of airflow interaction with light impurities during their flight in contactless PSC. As a result of analytical study examined contactless movement of light impurities when entering multigrain single layer material, ie flow, in which crops are layers PSC each other with a certain interval and have the same kinematic characteristics. Based on the theoretical analysis established pattern of interaction of light particles of grain mixture with air flow during flight of contactless multi-grain placing a single layer of material in PSC. Established that the contactless movement of light impurities in the PSC, regardless of the input area of selection is in the range 0.015 ... 0.05 m, depending on their coefficient of sails. The goal of future research should be to establish contact interaction of light impurities from the grain mixture and air flow in the multilayer material placed in the PSC.