Конструювання, виробництво та експлуатація сільськогосподарських машин. Загальнодержавний міжвідомчий науково-технічний збірник.
Permanent URI for this communityhttps://dspace.kntu.kr.ua/handle/123456789/19
Ідентифікатор медіа: R30-03925 (рішення Національної ради України від 25.04.2024 р. № 1418).
Мови видання: українська, російська, англійська, періодичність - один раз на рік.
Browse
4 results
Search Results
Item Вплив параметрів барабана для подрібнення рослинних решток на надійність протікання технологічного процесу(ЦНТУ, 2021) Сало, В. М.; Лещенко, С. М.; Богатирьов, Д. В.; Salo, V.; Leshchenko, S.; Bohatyrov, D.В роботі проводиться оцінка параметрів барабана для подрібнення рослинних решток на надійність протікання технологічного процесу. Проаналізовано існуючі конструкції котків- подрібнювачів рослинних решток та обґрунтовано взаємозв’язок окремих конструктивних та технологічних параметрів подрібнювачів на якісні показники їх роботи і можливість забивання міжножового простору. Проведені експериментальні дослідження по оцінці впливу кута розхилу між сусідніми ножами та робочої швидкості агрегату на ймовірність забивання міжножового простору. Доведено, що підвищення швидкості руху подрібнювачів та збільшення кута розхилу між ножами сприяють зменшенню забивання міжножового простору рослинно-ґрунтовою масою навіть при підвищеній вологості. The paper presents the assessment of the parameters of a chopping rotor for shredding plant residues for the reliability of the technological process. The general objective of the work is to substantiate the design and experimental identification of rational parameters of crimp-rollers of plant residues based on the condition of preventing clogging of the inter-knife space with plant-soil mass. The existing designs of crimp-rollers of plant residues are analyzed and the interrelation of certain constructive and technological parameters of shredders on qualitative indicators of their operation and possibility of clogging of inter-knife space is substantiated. The design of a large diameter crimp-roller provides simultaneous full contact with soil of two and sometimes three knives, which during the operation of the roller, together with cutting stems, provides them clamping with soil particles between adjacent knives. The probability of clogging between knives with plant and soil mass increases sharply with the humidity level of the material. Experimental studies have been conducted to assess the effect of the angle of inclination between adjacent knives and the operating velocity of the unit on the probability of clogging the inter-knife space. It is proved that increasing the speed of the shredders and increasing the decay angle between the knives help to reduce clogging of the inter-knife space with plant-soil mass, even at high humidity. The introduction of technological processes of effective preparation of plant residues in the production of crop products will allow starting the system of soil conservation at a farm. It is most expedient to grind plant residues with driveless roller shredders, the main operating parts of which are rollers with knives mounted on the cylinder, and depending on the purpose, quantity and type of plant residues, rollers with large and small diameters are practically used. When shredding high-stem plant residues, it is recommended to use crimp-rollers of large diameter with the following parameters: speed of the unit is 7…8 m/s, the decay angle between adjacent knives is 42… 46º. These parameters of the crimp-roller of plant residues reduce the probability of clogging the inter-knife space to 8%.Item Визначення еквівалентної проекції висоти перетину барабана з непарною кількістю ножів(КНТУ, 2016) Богатирьов, Д. В.; Сало, В. М.; Кислун, О. А.; Bogatyrov, D.; Salo, V.; Kuslyn, О.Стаття присвячена теоретичному дослідженню впливу еквівалентної проекції висоти bек на точність визначення сили опору повітря барабану з ножами. Зроблено спробу уточнити площу опору в залежності від кутового положення та кількості ножів барабана котка-подрібнювача. Дослідження впливу еквівалентної проекції висоти на точність опису сили опору повітря барабану з непарною кількістю ножів показали, що відносна похибка зменшується у 1,5 рази, що пояснюється виключенням впливу невизначеності початкового кутового положення барабану. During the last few years Ukraine was filled with nontraditional and in some cases unknown technologies of crop science. The changes started by using imported harvesters which left practically all residues on the field. This practice allowed increasing the productivity of picking processes and to shorten the terms of harvest period but there appeared the problem of further processing of plant residues. The Ukrainian producers chose the simplest way to solve it and used disc equipment for soil cultivation. As a result the structure of surface soil was damaged, valuable agro-technical aggregates were mashed, which led to their transformation into dusty unstructured condition. There was also overtamping of subsoil, disfunction of the processes of aeration and infiltration, decrease of the storage of productive soil water in lower levels. Special machines are usually used in these cases abroad which are debris pulverisers. In Ukraine these machines are not well known, expensive and perceived by agricultural producers as part of the technological process which needs extra costs and not obligatory. Besides, according to the special design of every of these machines they do not provide necessary pulverization in the traditional for Ukraine production technologies. In order to determine the accurate draught of the crimp-roller it is necessary to take into account the force to overcome air resistance. The article presents theoretical research of the influence of introduction of equal-area projection of the height on the accuracy of calculation of the resistance power of the air of the cylinder drum with blades. The effort was made to specify the area of resistance depending on the angle setting and the number of blades of the crimp-roller. Research of introduction of the equal-area projection of the height on the accuracy of description of the power of air resistance of the crimp-roller showed that the fractional error decreases in 1,5 times. This is explained by the absence of the influence of uncertainty of the initial angle setting of the cylinder drum.Item Аналіз господарських випробовувань котка-подрібнювача рослинних решток соняшника(КНТУ, 2013) Богатирьов, Д. В.; Сало, В. М.; Bohatyrov, Dmitry; Salo, VasilyНапрям розробки та удосконалення сільськогосподарських машин для подрібнення рослинних решток в Україні є маловивченим але дуже актуальним. Представлено аналіз результатів польових випробовувань котка-подрібнювача вітчизняного. Основним показником роботи даної машини обрано співвідношення розмірів решток стебел соняшника після подрібнення. Наведені результати випробовувань свідчать про доцільність використання даного типу сільськогосподарської техніки. Agrarian economy of Ukraine and the global trend of environmentally friendly crop production leads to the search for new technologies of crop growing and developing the necessary technology. The need for fertilizers feed plants is always topical issue. Over the past decade, making huge quantities of mineral fertilizers significantly degrade the organic component of topsoil . Also, use of chemicals in agriculture leads to environmental pollution. There are many cases where fertilizers and other chemicals made ill-conceived and sometimes irresponsible. This leads to the accumulation of chemicals in soil, groundwater, excessive content of their crop production , and a food - and food of animal origin. This man-made pollution of fertile soil affects the quality of agricultural products , which can lead to increased morbidity. Widespread use of pesticides has created and specific problems associated with the acquisition of weeds, pests and pathogens resistance to them. Direction of development of agricultural machinery for crushing plant residues in Ukraine is a little known but very important. The analysis of the results of field testing of the roller-crusher. The main indicator of this unit size selected residues of sunflower stalks after shredding. The results of the tests indicate the feasibility of using this type of agricultural machinery.Item Експериментальні дослідження впливу швидкості руху котка-подрібнювача на якість подрібнення рослинних решток соняшнику(КНТУ, 2014) Богатирьов, Д. Б.; Сало, В. М.; Мачок, Ю. В.; Bohatyrov, D.; Salo, V.; Machok, Y.Наведений напрям розробки та удосконалення сільськогосподарських машин для подрібнення рослинних решток в Україні є новим та дуже актуальним. Представлено аналіз результатів польових випробовувань котка-подрібнювача вітчизняного виробництва. Основним показником роботи даної машини обрано співвідношення розмірів решток стебел соняшнику після подрібнення в залежності від швидкості руху агрегата. Наведені результати випробовувань свідчать про доцільність використання даного типу сільськогосподарської техніки. Agrarian economy of Ukraine and the global trend of environmentally friendly crop production leads to the search for new technologies of crop growing and developing the necessary technology. The need for fertilizers feed plants is always topical issue. Over the past decade, making huge quantities of mineral fertilizers significantly degrade the organic component of topsoil . Also, use of chemicals in agriculture leads to environmental pollution. There are many cases where fertilizers and other chemicals made ill-conceived and sometimes irresponsible. This leads to the accumulation of chemicals in soil, groundwater, excessive content of their crop production , and a food - and food of animal origin. This man-made pollution of fertile soil affects the quality of agricultural products , which can lead to increased morbidity. Widespread use of pesticides has created and specific problems associated with the acquisition of weeds, pests and pathogens resistance to them. Direction of development of agricultural machinery for crushing plant residues in Ukraine is a little known but very important. The analysis of the results of field testing of the roller-crusher. The main indicator of this unit size selected residues of sunflower stalks after shredding. The results of the tests indicate the feasibility of using this type of agricultural machinery.