Конструювання, виробництво та експлуатація сільськогосподарських машин. Загальнодержавний міжвідомчий науково-технічний збірник.
Permanent URI for this communityhttps://dspace.kntu.kr.ua/handle/123456789/19
Ідентифікатор медіа: R30-03925 (рішення Національної ради України від 25.04.2024 р. № 1418).
Мови видання: українська, російська, англійська, періодичність - один раз на рік.
Browse
7 results
Search Results
Item Дослідження зносостійкості сталі 65Г з різними фізико-механічними властивостями при зношуванні в абразивній масі(КНТУ, 2016) Дворук, В. І.; Борак, К. В.; Добранський, С. С.; Dvoruk, V.; Borak, К.; Dobranskyi, S.Досліджено вплив природи, твердості абразивного матеріалу та тиску абразивної маси на зносостійкість сталі 65Г з різними фізико-механічними властивостями при зношуванні в абразивній масі, що імітує ґрунт. The purpose of research – to investigate the influence of nature and abrasive hardness and pressure abrasive wear resistance to steel weight 65Г with different physical and mechanical properties in wear in abrasive mass. The work for predicting the durability of the tillage work reinforced by electrical discharge machining, studies were conducted relative and absolute wearing ability of soils with different fractional composition, and to take account of the impact speed and pressure of the soil surface was made two-factor experiment. The criterion of optimization in the studies were offered: σW - durability km/h. As a result of the research might draw the following conclusions: - increased durability samples at reduced speed, due to the increase of dynamic loads on the surface friction. - surface wear resistance is significantly reduced with increasing pressure on the specific sample is explained by the fact that the increase in pressure may cause such negative processes as mikrorizannya metal surface with abrasive grains. - 65 G enhanced wear resistance of steel during quenching and tempering average of 15 ... 30%, the electrical treatment to 60..80% despite external factors (pressure and speed).Item Дослідження складу забруднень робочої рідини гідросистем дорожньо-будівельних машин, тракторів та автомобілів(КНТУ, 2013) Русских, В. В.; Russkikh, ViktorВ статті розглянуті переваги і недоліки об’ємного гідроприводу перед електричним приводом та механічними передачами, а також переваги та недоліки шестеренних насосів. Визначено, що основним видом зношення деталей шестеренного насосу є абразивне зношення. Наведено, що основна причина виходу з ладу шестеренних насосів є забруднення робочої рідини. Визначено фактичний вміст механічних домішок в робочій рідині гідросистем машин та якісна оцінка забруднень. Purpose of the article determination of actual composition of mechanical admixtures in the working liquid of gidrosistem road – build machines, tractors and cars. Advantages and lacks of by volume gidroprivoda, and also advantages and lacks of cog-wheel pumps, are considered in the article. It is set that the basic type of wear of details of cog-wheel pumps is an abrasive wear, and by principal reason of output them from a line-up is contamination of working liquid. It is set that the basic type of wear of details of cog-wheel pumps is an abrasive wear, and by principal reason of output them from a line-up is contamination of working liquid. The analysis of contaminations and signs of their education and penetration in gidrosistemy of machines is executed. Actual maintenance of mechanical admixtures is certain in the working liquid of gidrosistem. The high-quality estimation of contaminations is executed. The results of researches allow to set the ways of decline of wear of details of cog-wheel pumps, due to the decline of level of contamination of working liquid.Item Вплив експлуатаційних факторів на зношування гільз циліндрів двигунів внутрішнього згорання(КНТУ, 2008) Капелюшний, Ф. М.; Калита, М. М.; Катеринич, С. Є.; Солових, А. Є.Робота присвячена вивченню впливу експлуатаційних факторів на зношування гільз циліндрів двигунів внутрішнього згорання. Досліджено характер розподілу величини спрацювання по твірній деталі в залежності від міри впливу факторів зношування. Work is devoted the study of influence of operating factors on the wear of shells of cylinders of combustion engines. Research of character of distributing of size of спрацювання is on a formative detail depending on the measure of influence of factors of wear.Item Дослідження зношування робочих органів дискових борін(КНТУ, 2008) Герук, С. М.; Борак, К. В.; Нечипоренко, В. О.Наведено результати досліджень зношування робочих органів дискових борін та встановлено особливості характеру їх спрацювання для вітчизняних і зарубіжних машин. It is presented results of researches of wear process of working organs of disk harrows and it is established features of character of their deterioration for domestic and foreign machines.Item Зміна форми леза ґрунтообробних знарядь при зношуванні(КНТУ, 2015) Козаченко, О. В.; Шкрегаль, О. М.; Каденко, В. С.; Kozachenko, Oleksiy; Shkrohal, Alexander; Kadenko, VolodimirВ статті розглянуто напрямки підвищення технічного рівня робочих органів ґрунтообробних знарядь, зокрема культиваторів для міжрядного та суцільного обробітку ґрунту. Визначено напрямки удосконалення і підвищення довговічності культиваторних лап при застосуванні локального зміцнення твердосплавними матеріалами, встановлено можливість формоутворення зубчастого леза при експлуатації. The aim of this work is to study the dynamics of work wear tillage implements the example cultivators paws with curved shape and impact assessment geometrical parameters of local strengthening the interaction blade with an abrasive environment In the article the ways of raising the technical level of the working bodies of tillage implements, including cultivators for inter-row cultivation and continuous. Directions improved and durability cultivators paws when using local hardening carbide materials The possibility of forming toothed blades during operation Research deterioration of working with different types of cultivators strengthening indicates the feasibility of gear cutting surfaces can be formed during operation.Item Дослідження ефекту самозагострення монометалевих і зміцнених двушарових лез прорізаючого робочого органу(КНТУ, 2014) Павлюченко, І. С.; Pavlyuchenko, І.Наведено проблему забезпечення підвищення надійності агрегатів прямого посіву. Розглянуто використання різних видів зміцнення лез прорізаючого робочого органу. Визначено методику дослідження процесу зношування. Наведено результати випробування дослідних зміцнених зразків зубів прорізаючого робочого органу. Охарактеризовано умови досягнення явища самозагострення лез. The aim is to study the reliability of direct sowing seeders and self sharpening effect monometallic and reinforced double-layer blades cutting through the working body. Research and wear blunt blades cutting through the working body drills conducted on the basis of educational management. The survey provided the characteristic types and causes of failures of business seeders direct sowing. Defined relationship between blunt and self-sharpening blades working body. Schedules dynamics wear different types of blades and their results matched the best material for surfacing hardening effect self sharpening blades. Depicted forming monometallic profiles and dual-layer reinforced blades working body during wear. Characterized sharpening blades need to exploitation. According to experimental data determined in the same way that longevity depends exacerbation of linear wear blades that for steel material composition Steel 5 + manual arc surfacing electrode T-590 has the smallest value.Item Трибологічна надійність важконавантажених пар тертя сільськогосподарських машин. Метод дослідження(КНТУ, 2010) Гупка, Б. В.; Gupka, B.В роботі досліджено можливість використання синтезатора металів "Форсан" в системі важконавантажених пар тертя сільськогосподарських машин з позиції структурно-енергетичної теорії тертя та зношування для управління процесами активації і пасивації. Проведені експериментальні дослідження триботехнічних властивостей пар тертя на стенді МТ-1. Показано, що найбільша ефективність застосування "Форсан" проявляється при введені його в ЛИТОЛ. Possibility of the use of synthesizer of metals of "Forsan" is in-process investigational in the system of heavy loaded pair of friction of agricultural machines from position structurally to the power theory of friction and wear for a management the processes of activating and passivation. Experimental researches of tribotehnical properties of pair of friction are conducted on the stand of MT-1. It is rotined that most efficiency of application of "Forsan" shows up at entered it in LITOL.