Конструювання, виробництво та експлуатація сільськогосподарських машин. Загальнодержавний міжвідомчий науково-технічний збірник.
Permanent URI for this communityhttps://dspace.kntu.kr.ua/handle/123456789/19
Ідентифікатор медіа: R30-03925 (рішення Національної ради України від 25.04.2024 р. № 1418).
Мови видання: українська, російська, англійська, періодичність - один раз на рік.
Browse
6 results
Search Results
Item Техніко-економічне обґрунтування геометричних параметрів біонічних культиваторних лап на основі морфології риб(ЦНТУ, 2023) Теслюк, Г. В.; Алієв, Е. Б.; Теслюк, Ю. В.; Tesliuk, H.; Aliiev, E.; Tesliuk, Yu.Метою досліджень є проведення геометричного розрахунку біонічних культиваторних лап на основі морфології риб та побудова їх тривимірних моделей. У результаті аналізу морфології і локомоції риб та обробки їх фотозображення з використанням розробленого програмного забезпечення в середовищі Visual Studio C++ і бібліотеки OpenCV та методів зворотного інжинірингу (Reverse Engineering) проведено апроксимацію зовнішнього і внутрішнього контурів хвостового плавника деяких риб. У результаті аналітичних досліджень проведено геометричний розрахунок рівнянь регресії опуклого і увігнутого зовнішнього контуру біонічних культиваторних лап на основі морфології хвостового плавника риби та побудовані їх тривимірні моделі в SolidWorks. Therefore, the challenge of aligning the morphology of terrestrial and aquatic fauna with the surface of soil cultivation implements is relevant and requires attention. The research objective is to perform geometric calculations for bionic cultivation tines based on fish morphology and create their three-dimensional models. The analysis of fish morphology and locomotion, along with image processing using developed software in the Visual Studio C++ environment, OpenCV library, and reverse engineering methods, facilitated the approximation of the outer and inner contours of the tail fin of certain fish species. Through analytical investigations, the geometric calculations for the regression equations of convex and concave outer contours of bionic cultivation tines based on the morphology of fish tail fins were conducted, and their three-dimensional models were built using SolidWorks. The analysis of tail fin morphology allowed for the application of rays (radials) to cultivation tines. These rays are aligned along the axial line of the tail fin with displacement toward the outer contour. A general regularity in their arrangement was established and represented as a system of equations. Corresponding models of cultivation tines with guiding rays were constructed using software packages such as Wolfram Cloud and SolidWorks. From a technical and economic perspective, the implementation of the developed bionic cultivation tine shapes can reduce the equipment's drag resistance by 5–10%, leading to a higher economic benefit upon their adoption.Item Проектування та результати випробувань робочого органу для глибокого розпушення міжрядь цукрових буряків(КНТУ, 2009) Ветохін, В. І.; Кутя, П. О.; Vetohin, V.; Kutya, P.У статті запропонована загальна методика проектування безполицевих грунтообробних робочих органів. Проаналізовані недоліки відомого робочого органа знаряддя для глибокого розпушення міжрядь цукрових буряків. Визначені теоретичні основи та описано проектування нового робочого органу. Наведено данні порівняльних польових досліджень показників роботи знарядь, у тому числі з визначенням врожайності культури. In the article the described general method of projecting of mold boardless soil loosening working tools. The disadvantages of working tools dip loosening of row-spacing of sugar beet. The theoretical bases were specified and the projecting of new working tool was described. The data of comparative field research of characteristic, including the ones with the determination of crop productivity were citedpositions.Item Методика експлуатаційних досліджень зношування робочих органів дискових ґрунтообробних знарядь(КНТУ, 2009) Герук, С. М.; Борак, К. В.; Geruk, S.; Borak, K.Наведена методика експлуатаційних досліджень зношування робочих органів дискових грунтообробних знарядь. Розроблена методика дозволяє досліджувати закономірності та характер процесу зношування, динаміку зношування, вплив експлуатаційних факторів на зносостійкість та ресурс дискових робочих органів. The method of operating researches of wear of workings organs of disk soil instruments is resulted. The developed method allows to probe conformities to the law and character of process of wear, dynamics of wear, influence of experimental factors on wearproofness and resource of disk workings organs.Item Експериментальні дослідження процесу транспортування зернового матеріалу шнеком(КНТУ, 2015) Куликівський, В. Л.; Палійчук, В. К.; Боровський, В. М.; Kulykivskyi, Vladimir; Palіychuk, Vladimir; Borovskyi, VictorНаведена методика та результати експериментальних досліджень ефективності роботи гвинтових робочих органів транспортерів. Представлені стенди для проведення досліджень зі встановленими на них необхідними пристроями, механізмами і приладами для зміни, регулювання та вимірювання конструктивно-кінематичних параметрів гвинтових транспортерів. Визначені критерії оптимізації, а також фактори, що впливають на них. Experimental studies of the transportation of grain materials screw working body carried out in order to create an effective and reliable design of the screw. The method and results of experimental studies the effectiveness of the work of screw conveyors. The stands for research fitted with the necessary devices, mechanisms and instruments for change, management and measurement of structural and kinematic parameters of screw conveyors. Well the criteria of optimization as the factors influencing them. To study the effect of vibration elements screw feeder to transport efficiency. Experiments with vibration screw feeder found in all cases, a decrease in the circulation of the transported material, increasing the productivity of the screw.Item Визначення точного геометричного положення виконавчого органу просторової системи приводів(КНТУ, 2011) Струтинський, С. В.; Strutinsky, S.Розроблено спеціальні пристрої для вимірів точного просторового положення виконавчого органу просторової системи приводів. Пристрої мають вигляд трьох точних сфер розташованих на виконавчому органі. Виведені аналітичні залежності для визначення просторового положення виконавчого органу. Наведено результати апробації запропонованого пристрою при експериментальних вимірах. Порівняння експериментальних вимірів із теоретичними розрахунками підтвердили ефективність розроблених пристроїв та запропонованої методики вимірів просторового положення виконавчого органу. The special devices are worked out for measuring of exact spatial position of executive branch of the spatial system of occasions. Devices have the appearance of three exact spheres located. Located on an executive branch. Shown out analytical dependences for determination of spatial position of executive branch. Results over of approbation are brought, offered device at the experimental measuring. Comparing of the experimental measuring to the theoretical calculations confirmed efficiency of the worked out devices and offered methodology of measuring of spatial position of executive branch.Item Методика експериментальних досліджень ефективності роботи та довговічності гвинтового робочого органу транспортера(КНТУ, 2011) Куликівський, В. Л.; Kulikivskiy, V.Наведена методика експериментальних досліджень ефективності роботи і довговічності гвинтового робочого органу транспортера. Представлена лабораторна установка для проведення досліджень зі встановленими на ній необхідними пристроями, механізмами і приладами для зміни, регулювання та вимірювання конструктивно-кінематичних параметрів експериментального гвинтового транспортера. Визначені критерії оптимізації, а також фактори, що впливають на них. The method of experimental researches of work and longevity of spiral working organ of conveyer is resulted. A laboratory fluidizer is presented lead through of researches with the necessary devices mechanisms and devices set on it for a change, adjusting and measuring of structurally kinematics parameters of experimental spiral conveyer. The criteria of optimization, and also factors which influence on them, are certain.