Конструювання, виробництво та експлуатація сільськогосподарських машин. Загальнодержавний міжвідомчий науково-технічний збірник.
Permanent URI for this communityhttps://dspace.kntu.kr.ua/handle/123456789/19
Ідентифікатор медіа: R30-03925 (рішення Національної ради України від 25.04.2024 р. № 1418).
Мови видання: українська, російська, англійська, періодичність - один раз на рік.
Browse
9 results
Search Results
Item До розрахунку зубців прямозубих циліндричних передач на згин(ЦНТУ, 2020) Невдаха, Ю. А.; Дубовик, В. О.; Невдаха, Н. А.; Златопольський, Ф. Й.; Nevdakha, Yu.; Dubovyk, V.; Nevdakha, N.; Zlatopolskiy, F.; Дубовик, В. А.; Златопольский, Ф. И.В роботі аналізуються розрахункові схеми циліндричної прямозубої передачі на згин зубців. Розглядається найбільш поширена розрахункова схема злому зубця, де небезпечний переріз злому зуба відбувається у основі ножки вище кола діаметра западини зубців. На практиці реальний же злом зубця лежить нижче діаметра западини зубців і має опуклу форму перерізу. Для більш точного розрахунку зубців на згин досліджували коефіцієнт форми зубців. В результаті встановлено, що коефіцієнт форми зуба зменшується зі збільшенням кількості зубців. The aim of the work is to improve the calculations of spur cylindrical wheels per bend, due to the fact that the existing formulas do not give the actual value of the maximum stress, and the diagram does not correspond to the real law of stress distribution. In order to obtain satisfactory results, it is more correct to calculate the teeth at the maximum local stress. Combining the coefficients and substantiating the calculated dependence to determine the value of the coefficient of the shape of the tooth under load, applied at any point of the working profile of the tooth, to obtain formulas for the bending strength of the teeth of the gear and wheel. When calculating the bending teeth, the calculation is based on the stresses arising at the base of the tooth, under the load applied at the top of the tooth. Consider first the most common calculation scheme. Dangerous section of the tooth as seen from the plot of total stresses indicates that the maximum normal stress occurs on the non-working side of the tooth - the compression side, however, since fatigue cracks occur at the base of the tooth on the stretching side, the calculation is based on tensile stress on the working side. The hypothesis of non-curvature of flat sections is unfair for short beams of variable cross section, so the total diagram does not correspond to the real law of stress distribution. But at the base of the tooth near the transition curve is the place of stress concentration. The actual dangerous cross-section lies below the cross-section of the depression, this is confirmed by the fact that the fatigue cracks form an angle with the load curve close to straight, and the fracture of the tooth has a convex shape. In this case, it is more correct to calculate the teeth at the maximum local stress. Combining the coefficients obtained a calculated dependence to determine the value of the coefficient of the shape of the tooth under load, applied at any point of the working profile of the tooth. As a result of the study it was found that the coefficient of tooth shape decreases with increasing number of teeth. This result was expected because as the number of teeth increases, the angle between the teeth decreases, and neighboring teeth perceive part of the stress that occurs in the loaded tooth. The formulas for checking the bending strength of gear teeth and wheels are obtained. The above refinement calculations of the teeth on the bend reflect the beneficial effect of improving the accuracy of the manufacture of teeth. В работе анализируются расчетные схемы цилиндрической прямозубой передачи на изгиб зубцов. Рассматривается наиболее распространенная расчетная схема излома зубцов, где опасное сечение излома зубьев происходит в основе ножки выше круга диаметра впадины зубцов. На практике реальный же излом зубьев лежит ниже диаметра впадины зубьев и имеет выпуклую форму сечения. Для более точного расчета зубьев на изгиб исследовали коэффициент формы зубьев. В результате установлено, что коэффициент формы зуба уменьшается с увеличением количества зубьев.Item Стендові випробування штанг широкозахватного обприскувача(КНТУ, 2015) Паламарчук, П. В.; Гавриленко, М. П.; Сташків, М. Я.; Бортник, І. М.; Palamarchuk, Petro; Gavrylenko, Mykola; Stashkiv, Mykola; Bortnyk, IgorВ статті описано стендові випробування штанг широкозахватного штангового обприскувача виробництва ПАТ «Богуславська сільгосптехніка». Дослідження проведено на стенді для випробування причіпних обприскувачів на динамічні навантаження. У результаті проведених досліджень отримано значення напружень у найбільш небезпечних перетинах елементів штанг обприскувача, значення прискорень та кутових швидкостей секцій штанг. The objective of investigation is experimental studies of stress distribution in the most dangerous sections of elements of barbells of sprayer; determine the size and nature of changes in acceleration and angular velocity of sections barbells of sprayer. The article describes bench tests of barbells of sprayer production of PJSC “Boguslav agricultural machinery”. The study was conducted on the stand for testing trailed sprayers for dynamic loading. As a result of research obtained values of tensions in the most dangerous sections of the elements of barbells of sprayer, meaning acceleration and angular velocity sections of barbells of sprayer. Obtained by conducting bench tests of barbells of sprayer values of stresses in the elements of barbells of sprayer, the size and character of change of acceleration and angular velocity of sections of barbells of sprayer is the basis for simulation modeling in the design of machines for chemical plant protection.Item Фізичні аспекти взаємодії в системі "РОГМ-ґрунт"(КНТУ, 2015) Аулін, В. В.; Тихий, А. А.; Войтов, В. А.; Aulin, Viktor; Tihiy, Andrey; Voytov, ViktorВ статті розроблена функціональна модель процесу взаємодії РОГМ з середовищем ґрунту. Представлені процеси тертя та зношування в ґрунті, які реалізуються на фоні взаємообміну показників самого РОГМ із середовищем ґрунту і являють собою складну сукупність фізико-хімічних явищ. При розгляді закономірностей взаємодії в ТТС "РОҐМ-ґрунт" враховується як зовнішня структура, так і внутрішня будова. Показано зміну елементного складу прилеглих до РОҐМ шарів ґрунту, що свідчить про процеси масопереносу і сегрегації під час взаємодії в ТТС "РОҐМ-ґрунт". Представлені закономірності протікання процесів тертя і зношування РОГМ в залежності від його структурованості та гранулометричного складу. Досліджено стан ґрунту при дії РОҐМ, визначено розподіл його щільності за глибиною оброблюваного шару, за типами ґрунтів виявлено різний характер розподілу щільності, структури, пористості та вмісту гумусу за глибиною, отримано рівняння регресії між щільності ґрунту і вмістом гумусу. The paper developed a functional model of the interaction with the environment WBTM-soil. Presented friction and wear processes in the soil that are implemented against the background of the WBTM interchange indicators of soil and the environment is a complex set of physical and chemical phenomen. When considering the patterns of interaction in TTS " WBTM-soil " takes into account both external structure and internal structure. Shows the change in the elemental composition of the surrounding WBTM-soil layers, indicating that the process of mass transfer and segregation during interaction TTS "WBTM-soil." Presented patterns of processes of friction and wear WBTM depending on its structure and grain size. The state of the soil by the action WBTM, determined its density distribution in the depth of the treated layer of soil types found on the distribution of different density, structure, porosity, humus content and the depth obtained regression equation between the density of soil and humus content.Item Моделювання інтенсивності експлуатації пуансонів холодного видавлювання за допомогою програмного комплексу DEFORM v.10(КНТУ, 2011) Кришкін, Б. Б.; Мірзак, В. Я.; Ставерська, О. Е.; Черпак, А. О.; Kryshkin, B.; Mirzak, W.; Staverskaya, О.; Cherpak, А.У статті наведені результати моделювання температурного стану та напружень в пуансоні для зворотнього видавлювання корпусів спеціальних накидних гайок. На підставі результатів моделювання із застосуванням пакету програм DEFORM v.10 та результатів експериментального визначення навантажень на пуансони запропонована система плинного моніторингу довговічності інструменту. In the article results over of design of the temperature state and stresses of puncheon are brought for the reverse squeezing out of corps of heads of special nuts. On the basis of results of design with the use of package of softwares of DEFORM v.10 and data of experimental determination of loading on puncheons the system of the current monitoring of longevity of instrument is offered.Item Закономірності контактної взаємодії частинок середовища ґрунту з РОГЗМ, зміцненими композиційними матеріалами та покриттями(КНТУ, 2014) Аулін, В. В.; Тихий, А. А.; Карпушин, С. О.; Aulin, V.; Tihiy, А.; Karpushin, S.В статті наведено результати дослідження напружено-деформованого стану ґрунту, як безперервного середовища, під дією робочих органів ґрунтообробних і землерийних машин (РОГЗМ). Експериментально встановлено зв'язок напруження в ґрунті зі зносом РОГЗМ. Наведено теоретичний аналіз напружено деформованого стану локальної області зміцненого поверхневого шару РОГЗМ, в якій розміщено наповнювач, включення або зміцнювальна фаза. За допомогою комп'ютерного моделювання досліджено характер розподілу напруження в зміцненому поверхневому шарі РОГЗМ в області контактної зони в стаціонарних та динамічних умовах. Сформульовано контактну задачу, наведені граничні умови та розв'язок у вигляді складових поля напруження. Враховуючи характеристики наповнювача, їх вміст в композиційному матеріалі і покритті, встановлено зв'язок між напружено-деформованим станом і зносом. The paper presents the results of the study stress-strain state of the soil as a continuous medium, under working parts of cultivation and digging machines (WPCDM). Experimentally established relationship stress in soil with demolition WPCDM. Theoretical analysis of stress strain state of the local area, hardened surface layer WPCDM that contains filler inclusion or strengthens phase. Using computer simulation investigated the distribution of stresses in a reinforced surface layer WPCDM in the contact zone in stationary and dynamic conditions. Formulated contact problem given boundary conditions and the solution in the form of components of the field strain. Given the characteristics of the filler, their content in the composite material and the coating, the connection between the stress-strain state and wear.Item К вопросам определения напряженно-деформированного состояния при отрезке деталей в штампах(КНТУ, 2014) Хорольский, В. Л.; Khorolskyi, V.В работе рассмотрены вопросы определения нормальных и касательных нагрузок, действующих на режущие кромки отрезных штампов, получены уравнения для определения произвольных постоянных нагрузки. Выполнены экспериментальные исследования определения направления течения отрезаемого металла. У роботі розглянуті питання визначення нормальних і дотичних напружень, що діють на різальні кромки відрізних штампів, отримані рівняння для визначення похідних постійних навантаження. Виконано експериментальні дослідження визначення напрямку течії металу, що відрізають. The purpose of this research is to determine the stresses arising at the cutting edges of the working tool of cutting forces on the stress state of the working parts of cutting dies. The paper discusses the issues of determining the normal and tangential forces acting on the cutting edge of the cutting dies, there are derived the equations to determine the arbitrary constant load. Experimental studies determine the direction of flow of the cut metal. Conclusions. The studies identified the loads acting on the contact surfaces of the cutting tool with cut material without considering the influence of other factors on the state of stress of the working parts of cutting dies. Fulfilled experimental studies confirmed the theoretical conclusions about the predominant direction of flow of the cut metal from the gap when cutting without clamp with the available small area of the metal flow in the gap.Item Розподіл напружень у сипкому середовищі обмеженому стінками споруди силосного типу(КНТУ, 2010) Ковбаса, В. П.; Ярошенко, В. В.; Kovbasa, V.; Yaroshenko, V.На основі теорії пластичності розв’язана задача про розподіл компонентів напружень зв’язного сипкого середовища у спорудах силосного типу. Встановлено зв’язки механічних властивостей сипкого середовища, геометричних параметрів силоса з напруженнями у споруді та умовами граничної рівноваги матеріала, крім визначення форм ліній ковзання при порушенні граничної рівноваги. On the basis of plasticity theory the the problem about distribution of components of pressure of the coherent loose environment in a construction of silage type is solved. The copulas of mechanical properties of friable environment, geometrical parameters of silosa are set with tensions in building and terms of maximum equilibrium of materiala, except for determination of forms of sliding lines at violation of maximum equilibrium.Item Трибофізичне обґрунтування зміни напружено-деформованого стану ґрунту під час дії РОГМ(КНТУ, 2012) Аулін, В. В.; Aulin, V.В статті дано теоретичне обґрунтування трибофізичного підходу до закономірностей взаємодії в системі "РОГМ-ґрунт". При цьому отримано рівняння стану ґрунту у векторній формі, а також через поле напружень і деформацій. In the article the characteristic changes of properties and tensely-deformed state of soil are considered during the action of operative parts of tillage machines. Their influence is educed on conformities to law of friction and wear in soil. The basic methods of decline of friction, wear and power-hungryness of till of soil are set forth.Item Технологія наплавлення отворів зі зменшеними температурними похибками(КНТУ, 2010) Заболотний, С. А.; Zabolotny, S.Обґрунтовано доцільність керування потужністю зварювальної дуги в процесі наплавлення покриттів на поверхні деталей складної конфігурації. Показано, що така технологія наплавлення дозволяє зменшити перепади температур та вирівняти поле напружень в деталі, які є причиною спотворення її геометрії. Reasoned arguments concerning the control over the power of welding arc in the procedure of surfacing coating on the surfaces of the details having complicated configurations are well-founded here. It is also shown that such a technology of surfacing permits to reduce over falls of temperature and to even the field of tensions in the detail which is the reason of distortion of its geometry.